Anycubic Photon Printer Owners 造訪社團 » LCD

Update: The Blob Chronicle woes culprit was not resin related nor was it caused by defective LCD. It turns out my main board was faulty, giving intermittent output and variable results. Some times good prints but mostly failed prints including the blobs, making it extremely difficult to diagnose the problem and caused a lot of confusion on my part and to the very kind photonsters who were very nice to help me with my problem. I got my main board from Anycubic and although, I haven’t had the time to test it out thoroughly yet, my first 3 prints since the main board replacement have been successful ?? .

Flex100 + Anycubic Gray 25:75 ratio = Epic Fail Blob ?

翻譯年糕

Does anyone have experience with the sparkmaker resin range on the photon? Particularly the LCD-N.

翻譯年糕

Newbie here, just got my photon and only printed a few times. I have a quick round of questions and I though you might be able to help me with some answers.

1. How do you prevent air bubbles from creating inside the resin from the build platform going down into the resin ? I've seen them form on the edges of the build platform a couple of times when printing starts.

2. I saw after each print that a thin layer of moisture is forming between the LCD and the FEP film. Am I assuming correct that it is because of the temp difference between the room temperature and the hot LED area below ? Do I need to remove the VAT each time and clean it or can I go printing without issues ? Btw my room temp is 25C and relative humidity is 45%.

3. How do you safely dispose of the nasty chemicals resulting from washing the printed objects ? I assume they need to be handled like car oir or other nasty stuff. Does this relate to local country/city regulations ?

4. I ordered some Monocure 3D Rapid resin. How does it compare to the Anycubic resin in terms of quality/ease of use and also does it smell less or more ?

5. My DIY arduino based VOC counter is at max while printing and goes down only after two hours from the printing end while the 4x4m room is with the door / windows open and continuously ventilated with a big and powerful HEPA/carbon filter, as I don't have yet an enclosure which I suppose is the best way of dealing with the fumes ?

翻譯年糕

Hi, anybody can help with this ?
z motor stops moving at mid print, LCD keeps exposing resin, no error message, stopping print and moving z via menu works.

翻譯年糕

Trying to update firmware. While clicking on 255.lcdimg
it shows unknow file format

翻譯年糕

ALL 3DP - 25 Best Resin (LCD/DLP/SLA) 3D Printers of Fall 2018

https://all3dp.com/1/best-resin-dlp-sla-3d-printer-kit-st…/…

翻譯年糕

I thought my LCD screen was cracked after a levelling botch. As I was removing the old one to replace it, I realized the screen is actually Ok but the glass below it is actually cracked (not sure how it got cracked but not the screen). Anyway. do you know where I can find a spare for that part? I don't see it at FEPShop.

翻譯年糕

any reliable place in the states that sell the lcd with glass already assembled for sale for the photon?

翻譯年糕

Hello guys, got a kind of a silly question, is it safe to stare at the lcd screen (while illuminated) without the uv protection?

翻譯年糕

Guys check this out! Especially you Jack . I’ve tried my best to get this on camera, so please bear with me. (Bare?)

I’ve recently encountered the same problem a few of us have been having. Islands on my prints. Nothing but an annoyance, the prints themselves come out fine. These islands are in the same spot each time... and looky here! These spots are on the LCD screen. I can’t clean them off, they seem to be inside the machine itself. Time for a new screen? Gonna relevel and see if it goes away, but it’s worth mentioning that these dots are NOT random.

The other picture is from the slice of my print that I’ve been doing over and over recently. Notice anything? My hypothesis is that I’ve been leveling TOO close and damaging the screen just a little. Enough to make it a problem.

翻譯年糕