Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Chris LaRose
2019-11-08 06:39:16

Im ether going to cry or throw this machine out the window if I can't figure this out soon. The last photo is the FEP after I put my scraper through it, so likely the latter. I've run a bunch of calibration tests that came out great, not a settings issue. Different orientation and models all come out the with the same sheet of cured resin on the fep but no part of the print actually failed. This only seems to happen to prints over 30mm in Z, the calibration tests and one short print I did at 27mm looked great. I had an S with v2.9.9 I believe. I've updated to V5 firmware and that's made no difference.

Things that have changed since my last good print.

FEP- two of them, no I didn't leave the film on. Again the prints under 30mm are fine.

Resin (new bottle not different type)- if I got shit resin I would think even the small prints would fail.

Weather- it's winter now and it's colder on the room I print in then before.

LCD cooling and exhaust fans replaced- the exhaust fans didn't last two weeks and the cooling fan wasn't far behind. But even with the exhaust fan disconnected and the old cooling fan making a bunch of nosie it printed fine. The new ones are moving air fine.

I'm thinking this has to be ether it's too cold in the room I print in or my LCD is ether over heating or just having a glitch mid print and periodically curing a huge layer accross the whole screen. I feel like the butterfly pattern looks to confirm this, as it would pull that layer in to the middle as the print continued and the edges of that layer are super thin and flappy and it gets thinker as it gets closer to were the model was printing.

翻譯年糕

Evan Boone
2019-11-08 06:44:22

Chris LaRose
2019-11-08 07:17:55

Evan Boone
2019-11-08 07:19:05

Chris LaRose
2019-11-08 07:21:18

Evan Boone
2019-11-08 07:21:57

Chris LaRose
2019-11-08 07:27:14

Chris LaRose
2019-11-08 07:31:51

Patrick Stark
2019-11-08 09:04:48

Dave Dewees
2019-11-08 09:07:56

Chris LaRose
2019-11-08 09:20:44

Patrick Stark
2019-11-08 09:21:42

Chris LaRose
2019-11-08 09:22:22

Chris LaRose
2019-11-08 09:25:13

Kelly Thibodeau
2019-11-08 09:46:49

Greg Miller
2019-11-08 15:23:23

Chris LaRose
2019-11-08 20:56:40

Davy Struyf
2019-11-08 22:04:16

Chris LaRose
2019-11-08 23:29:44

Davy Struyf
2019-11-08 23:42:23

Chris LaRose
2019-11-09 00:07:16

Nicholas Taylor
2019-11-09 00:20:24

Nicholas Taylor
2019-11-09 00:22:25

Charlie Brett
2019-11-09 00:25:11

Nicholas Taylor
2019-11-09 00:26:16

Charlie Brett
2019-11-09 00:40:21

Chris LaRose
2019-11-09 00:48:05

Nicholas Taylor
2019-11-09 00:52:25

Nicholas Taylor
2019-11-09 00:54:25

RIcardo Castillo
2019-11-09 00:55:14

Mike Nye
2019-11-10 12:44:41

Mike Nye
2019-11-10 12:45:31

Matt Olsen
2019-11-17 01:14:34

Nicholas Taylor
2019-11-17 02:34:46

Matt Olsen
2019-11-17 03:17:43

Nicholas Taylor
2019-11-17 12:50:27

原文網址 Lex Toother
2019-11-08 06:08:20

There’s a couple small circles in my LCD screen that aren’t producing light and printing. Are these dead pixels or something else?

翻譯年糕

Elle Heilig
2019-11-08 06:13:14

Josh Ujak Lijewski
2019-11-08 06:16:28

Paul Joseph
2019-11-08 06:17:38

Ramon SG
2019-11-08 06:25:26

Lex Toother
2019-11-08 07:08:09

Joshua Byerly
2019-11-08 13:56:16

原文網址 Chris LaRose
2019-11-08 05:45:50

LCD cooling fan on the S, is it supposed to blow at the heat spreader or out of the machine?

翻譯年糕

Paul West
2019-11-08 05:52:04

Chris LaRose
2019-11-08 05:54:13

原文網址 Carlos Aguilar
2019-11-08 04:39:13

hey guys does anyone on this group have a tutorial for changing the lcd screen?

翻譯年糕

原文網址 Benjamin Kantor
2019-11-08 02:39:45

Anyone seen an error like this? I'm thinking it's a failing LCD screen, but it's strange that it's semi-symmetrical across the axis that the models were at to each other on the screen, and not symmetrical across the overall XY area of the screen. I also thought it might be under-supported models, but this one was a hollowed version of the same model.

翻譯年糕

Paul West
2019-11-08 02:40:45

Rob Gootz
2019-11-08 02:41:14

Adrian Carter
2019-11-08 02:41:35

Benjamin Kantor
2019-11-08 02:42:51

Adrian Carter
2019-11-08 02:43:50

Gary Houser
2019-11-08 02:49:34

Benjamin Kantor
2019-11-08 03:12:10

Derek Johnston
2019-11-08 03:20:45

原文網址 Ben Thompson
2019-11-07 12:00:30

I was having frame shearing problems and when I updated the firmware my Photon’s screen started acting funny and not producing the rectangle when doing the UV detection. I opened a ticket with Anycubic and they sent me a new motherboard. I just installed the new motherboard and the lcd screen problem is still happening. Any ideas appreciated, thank you!

翻譯年糕

原文網址 Mike Nye
2019-11-07 10:41:42

Hi Photonsters,

I'm still troubleshooting the failed prints on my photon with Anycubic support. They've asked me to disassemble the printer to check the LCD cable connection.

While I'm happy to do this, I don't think the LCD screen has problems - I've been able to print the resin exposure test plates just fine. I'd imagine that if the screen was faulty these exposure test plates wouldn't print properly...

The more I look into this, the more I think the problems are related to the "Eco Resin" that I bought with the unit.

I'd like to purchase some non-anycubic resin and try some test prints prior to disassembling my unit.

What are everyone's recommendations for resin? I'm in Western Australia so I don't have too much choice... It looks like I can get Monocure 3D Rapid locally - is this a good choice? What are people having success with?

Thanks!

翻譯年糕

Robert James
2019-11-07 10:45:25

Mike Nye
2019-11-07 10:46:13

Damo Cramp
2019-11-07 10:48:27

Robert James
2019-11-07 10:51:43

Mike Nye
2019-11-07 11:56:44

Mike Nye
2019-11-07 12:01:37

John Leonard
2019-11-07 12:25:07

Mike Nye
2019-11-07 13:05:50

Noah Belveal
2019-11-07 13:11:28

Damo Cramp
2019-11-07 13:12:01

Robert James
2019-11-07 13:18:18

Mike Nye
2019-11-07 13:18:45

Mike Nye
2019-11-07 13:19:29

Damo Cramp
2019-11-07 13:23:49

Mike Nye
2019-11-07 13:24:28

原文網址 Krunoslav Zlomislic
2019-11-06 20:47:27

where in europe on cheap side i can buy replacement for lcd to have spare ?

翻譯年糕

原文網址 Krunoslav Zlomislic
2019-11-06 14:53:59

and fun begins ,this morning after 1litre of resin printed lcd dont work any more , i isolated him with kepton tape like suggested ,did not have any leaks just print finished overnight with nothing in or out of it ,when i did test on lcd nothing .... crap ... do we have any warranty on lcd or it's gone in to wind after 1 litre of resin ?

翻譯年糕

Janne Sjöström
2019-11-06 15:19:03

Sam Davey
2019-11-06 15:35:29

原文網址 YH Ha
2019-11-06 13:01:35

Hi. This video is timelapse sculpting and painting of battle damaged Terminator T-800 from Movie 'Terminator Dark fate'. I am not used this for Photon but I used a similar lcd resin printer for this work. I think you guys interest it. You can see full video in here. https://youtu.be/yPuSkhGCanQ Thank you for watching :) 翻譯年糕