Anycubic Photon Printer Owners 造訪社團 » LCD

Hi everyone! I'm new at lcd printing, but I've read a lot of the groups experiences and I've learned a ton.
But... I would like to know if there is a way to print flat on the plate. I have a few waterline ships and printing them at an angle leaves a really messy bottom...
But my attemps have been unseccesfull.
It's at 1:2400 scale. Printed at 100 microns (test prints). In wanhao grey.
Does anyone has a suggestion to printing flat?
Thanks!!

翻譯年糕

2 prints in a row have stopped randomly in mid print. Part is stuck to FEP, looks like occurs in mid exposure. The printer LCD is at the normal screen. Doesn’t show the normal print completed message. I can navigate the LCD menu normally. 1st time failed around 94% into print. I cycled power and cleaned FEP and plate, restarted same print file on same usb stick, 2nd attempt failed around 30% into print making me think it’s not the slice itself. The usb is a Sandisk I’ve bought that has worked well for weeks. What is the most likely problem ?

翻譯年糕

Bad LCD or something else? Two perfect lines that cut across the LCD.

翻譯年糕

So technical advice guys, put the new screen that finally arrived in the Photon that was giving screen errors out of the box. Now it doesn't send anything to the screen when running the test and gives error tones on startup. Any ideas? Is it a main board fail out of the box? Could it be a dodgy lcd connector on the main board?

It seems a bit of a strange error to be presenting after something as simple as an lcd replacement.

Edit: Please note that the new screen was a warranty replacement as this unit had issues out of the box.

Edit 2: Ok so flashed the firmware and got rid of the other errors, but the problem with the screen persists. Looks like it's time to email support back again.

翻譯年糕

Day 2, still receiving lcd error code t-100 straight out of the box

翻譯年糕

Okay folks, how am I doing/what am I doing wrong?
Left to right, first print, failure to adhere.
Second print... I dunno, dingleberries, I guess you guys call them artifacts?
Thrid print, some errors in layers, an obvious break in the continuity of the layers.
On paper towels are the artifacts scrapes off the fep. Just peeled some resin off my lcd. Dunno how it got there.

翻譯年糕

Do the replacement LCDs from Anycubic tend to have a plastic cover on the shiny underside that needs removing? It _looks_ like there's a little white tab in one corner as if it's there so something can be peeled away, but it also looks like the tab _might_ be attached to part of the actual screen :p

翻譯年糕

Just received my printer, leveled fairly easily, wont even let me start the test print as it has an lcd 100 error. After updating it now has lcd 88 error. Yay

翻譯年糕

sorry for the crude quick video but I spotted some thing interesting to night while doing a print with clear resin during the exposher the lamp seems to be changing in intensity up and down it never goes out but it drops down to like %50 then back up the lcd its self is fine but i can see its the led panel its self, now i amuse its been doing this for a while print quality seems to be unaffected for now but im wondering if this is going to be a ishue to the point where i shod replace the leds and driver unit or let it go till thay stop working completely. so if any one has some guidance on this drop me a comment.

翻譯年糕

Another post, related to my n00bness: thoughts on why I might be getting.. "dingleberries" ? Extra, globshape resin not related to the item, in random layers. The second print had a big one, mid program, and my third one started one on like the fifth layer. what do you all recommend/use to clean your LCD screen, and your film? how often should I be straining/filtering for solids? 翻譯年糕