Anycubic Photon Printer Owners 造訪社團 » USB

It seems like all my printing problems were caused by the USB ?

Now just a question...I read that everyone here talks about the green resin that comes with the printer... Well, I bought the Photon on black Friday offer with an additional 500 ml grey resin. I received the grey resin and the printer with 2 distinct spedition (I received first the resin, so thanks for the heart attack), but in the printer package I found no resin. Is It correct or I should have received also the green one?

翻譯年糕

I received my Photon S today but is not reading the USB memory, when in it flashes but noting is shown on the Print screen . Any advice ?

翻譯年糕

Requesting some advice please. Photon S using 3d builder to fix any errors, resize and hollow and Chitubox to add supports followed by photon workshop (PW) to slice. Due to my machine i need to use PW to slice as a pws type file. My first thoughts were that i was adding supports in PW for all the failed prints. One of my issues with PW us that it doesnt refresh back to default slice settings (i.e. loads up slice settings from the previous print). This is making it hard to work off a reference point to tune the slice settings.

After printing the test cube and a small bust successfully, all of my prints are turning out to be pancakes on the bottom of the vat. side note, ive been carefully removing the pancakes by pressing lightly under the FEP at the edge of the print.

The first fail after the successful bust was the deadpool keychains, angled and supported. Settings as per the pic.

The next 2 or 3 failed prints was a lithopane, i must not have saved the stl just before slicing. This is where i started tweaking exposure times, bottom layer and layer thickness. Refer to the pic without the stl.

Following that i tried to print a resin funnel. I opened up the test cube to check its settings because i know that thing prints. Copied the settings and bam, another failed print.

So, last night i relevelled using the flint read method and gave the printer a clean with IPA. Went back to square one and printed the test cube. it was printing so i cancelled and loaded up the funnel again (which was raised about 5mm from the supports). The funnel failed but instead of a pancake, it had about 5mm of supports and what looks like the first 10 or so layers (will add a pic of failed print and pws settings when i get home from work).

Just before leaving for work, i went back to the bust that worked (which i must have sliced to the usb instead of to the project folder) and started printing that again to see if i can actually print anything at the moment.

Has anyone else had a similar experience with the Photon S, and what worked for you?

翻譯年糕

I suspect I know the answer, but somebody tell me if I'm completely screwed with this error. My print job froze with "Memory Error Code: M_11000. Please Try to Replug the USB disk and continue printing." I have done so, multiple times, and even switched flash drives and overwritten the existing file, just in case it was corrupted, and it always does the same thing... after returning to the proper level, it displays a solid blue screen while the flash drive LED flickers like mad. I've left it to do it's thing for a couple of hours, and it never advanced. The Pause and Stop menu options are completely unresponsive. All I can do is physically pull out the USB, which returns me to the same Memory Error Code above.
Is this print a lost cause? Of course it would have to happen 60% of the way through a large scale print job, when I just poured the last drop of Elegoo White into the machine this morning. (I've been putting off buying more since Amazon is currently asking $45 a bottle)

翻譯年糕

most of users here it will not affect, but anyway: dont use any diacritic or special symbols in name of file ?
just spent 1 hour investigating why my photon doesnt read usb ?

翻譯年糕

Question for the collective...

Has anyone had a print job come out half done/half pillars? I removed the print, ran the screen test, and it showed the half pillar. I reset the device and ran it again and came up fine. Not using the usb that came with device... but could it be a bad file or bad usb?

Sorry I didn’t take a photo because I wasn’t thinking and too grumpy... thankfully the models were hollowed though!

翻譯年糕

Ok I've been having a few issues the past few days. I have not had a successful print since Friday. I have included all relevant pictures. I have changed the USB to a new one, re-leveled the build plate, ran UV light test to make sure the screen is working. The only thing I feel I have not done is change the fep film. Would errors like these be caused by the fep film? I have included a picture of it as well.

翻譯年糕

Really weird print error. Is this the USB connection issue?

翻譯年糕

FYI I got my usb working, I had to read the photon slicer Manuel and it answered my question

翻譯年糕

Ok I have looked on thingyverse and can't see anything that is close to a mod to rotate the usb slot so it no longer stick straight out sideways
Is there such a mod out there to have the usb stick stick up so it can't be knocked etc

翻譯年糕