Anycubic Photon Printer Owners 造訪社團 » resin

I’ve been having issues with support settings for miniatures using siraya blu resin, anyone using it what settings are you using?

翻譯年糕

Has anyone used yellow transparent resin in a photon s? I cannot, for the life of me, figure out the correct exposure settings, and it's not on the photon s spreadsheet.

翻譯年糕

Help !
I just had a resin leak in my fep...
Changed everything cleaned up, got the baked resin off the lcd. Re-leveled and everything was working fine.

Now the touch screen is unresponsive...
Lit up but nothing is pressing.
And my plate is in the resin, i can't raise it.

翻譯年糕

Had my first failed print and unfortunately some resin is cured to the FEP. What the best way to save the existing resin and remove the cured resin without damaging the FEP. Thanks!!!

翻譯年糕

Quick question. I am printing on fauxton, firmware 5.x.x. I originally started with Anycubic clear, no issues. I have bought Monocure 3d rapid grey. Dialed the settings in normal 8s, bottom 80s, 5 bottom layers with .03 layer height. Prints are coming out perfect, a few support issues I have been ironing out by watching 3d pro videos. BUT ever since switching to the grey I end up with layers of random resin stuck to FEP, while no affect to model.

I should mention using Chitubox then file validator. Also a lexar usb. Leveling is perfect, I even leveled the machine with a laser (carpenter).

So is it exposure settings?

Attached is primed with grey, also needed a little more cleanup.

翻譯年糕

Well, I printed 4 pieces as soon as the printer arrived, no calibration and chitubox with default settings. They were ok, but poor details.
Yesterday I spent the day making tests to improve the quality. These pictures are from now, after the tests.
Now I am using 7 bottoms layers with 60 exposure, and the layers are 0.5 / 5.

Can you guys tell me if the quality is ok? I don’t know if the pictures are good enough, but I think they show them well.
The resine is Anycubic White... maybe with a crystal resine I could get more detais?

The last 2 miniatures are not ok, I have to check the supports, because the damage was in the same side.

翻譯年糕

So I did an exposure finder test with the dice masters I was trying to print with the new resin. The numbers in blue are the exposure seconds.

Interestingly enough, they start getting printed at 8sec, but I did print a full bed at 9sec and I was missing detail. I feel I should be printing more towards 5, but it’s not until 8 that it prints (at least the support hang) correctly.

What are your thoughts? Should I thicken the primary support and print at lower exposure, or should I print at 8sec? Or maybe a mid term? Any ideas are welcome ?

翻譯年糕

Question.
So far I have used successfully Anycubic translucent resins (about 5 litres) and I could hear the pop off the fep only 4-5 times at the beginning of each print.
I have just switched to Anycubic Skin and I can hear the pop after every single lift off the fep.
Is this normal or is my fep about to give up?
I am about 4 hours in a 5 hour print.

翻譯年糕

Does anyone have a really lound screeching noise from the Z axis? Its absolutely terrible, sounds like a firealarm when it moves in certain areas. Its only 2 weeks old and ive done less than 20 hours worth of printing.

I know The question are going to come: there is no resin on The z axis. Its not dropped or forcefully twisted

翻譯年糕

Is anyone here using their Photon to make jewelry molds .. any certain type of resin that should be used .. had my fun making mini characters and stuff but now to put it use for the reason I got it

翻譯年糕