Anycubic Photon Printer Owners 造訪社團 » EX

原文網址 Carlos Pilonieta
2020-01-23 22:48:57

I did this to my self ? ? ? . I had my photon for over a year. I had never had a fail print but I decided I need it to update the firmware to get better results. I never did any changes to the print settings or anything just send to print and get next day my print job. Now is been three times and just failures. What did change? First picture is my last work before failure.

翻譯年糕

Oleksandr Panforov
2020-01-23 22:52:22

Jlee Usn
2020-01-23 22:53:45

Paul Dodd
2020-01-23 22:55:07

Carlos Pilonieta
2020-01-23 23:35:33

Oni Cron
2020-01-23 23:46:33

Oni Cron
2020-01-23 23:49:20

Aaron McCommon
2020-01-24 10:54:57

Carlos Pilonieta
2020-01-24 12:26:35

原文網址 Sean Smith
2020-01-23 22:39:48

Ok so after doing some more research and trial and error, I think I managed to get the build plate leveled and zero’d correctly!!

I set the exposure time at 10 seconds, and the plate is moving!

Didn’t fill it too high this time either!!

Learning new things that are tedious and time consuming are always fun for me!!!

Hopefully this test will come out good then I can start printing all the models I downloaded!!

Now I know that some builds require adding some supports if you build stuff at angles or that have thin areas that could sag during building, and if anyone can let me know the names of any user friendly programs it would be greatly appreciated!!

翻譯年糕

Sean Smith
2020-01-23 22:43:16

Sean Smith
2020-01-23 22:43:33

Renato Gelmini
2020-01-23 22:49:44

Jonathon James Karafa
2020-01-23 22:51:57

Sean Smith
2020-01-23 22:53:44

Sean Smith
2020-01-23 22:56:12

Jonathon James Karafa
2020-01-23 23:14:32

Sean Smith
2020-01-23 23:14:55

Sean Smith
2020-01-24 00:18:01

Sean Smith
2020-01-24 00:18:11

James Swan
2020-01-24 00:35:57

James Swan
2020-01-24 00:36:01

Sean Smith
2020-01-24 00:46:01

Renato Gelmini
2020-01-24 00:46:16

Sean Smith
2020-01-24 00:46:16

Sean Smith
2020-01-24 00:56:22

Sean Smith
2020-01-24 01:18:12

Harold Crossley
2020-01-24 01:39:10

Logan Newbanks
2020-01-24 01:41:46

Matt Houghton
2020-01-24 01:42:27

Matt Houghton
2020-01-24 01:44:47

Jonathon James Karafa
2020-01-24 02:23:27

Jonathon James Karafa
2020-01-24 02:25:12

Matt Houghton
2020-01-24 02:26:23

Logan Newbanks
2020-01-24 02:27:24

Jonathon James Karafa
2020-01-24 02:30:04

Coleman Woody
2020-01-24 02:31:14

Jonathon James Karafa
2020-01-24 02:32:56

Coleman Woody
2020-01-24 02:34:03

Sean Smith
2020-01-24 03:43:03

Sean Smith
2020-01-24 03:47:57

Sean Smith
2020-01-24 03:48:10

James Swan
2020-01-24 03:48:37

Renato Gelmini
2020-01-24 03:49:11

Sean Smith
2020-01-24 03:49:27

Sean Smith
2020-01-24 03:49:45

James Swan
2020-01-24 04:04:30

Alex Vee
2020-01-24 04:07:59

Sean Smith
2020-01-24 04:31:28

Erwin Kauwenberg
2020-01-24 18:56:06

Rob Walker
2020-01-24 19:00:17

Sean Smith
2020-01-24 22:43:28

Alex Vee
2020-01-24 23:07:34

原文網址 Tom Cross
2020-01-23 22:15:49

I am having trouble with printing. When ever I print a model and the model itself is touching the base the print comes out looking like it is melting. But when I raise the model 3mm with supports the model turns out fine. Can anyone explain this?

翻譯年糕

Nipuna Gunarathne
2020-01-23 22:22:39

Mike Roof
2020-01-23 22:40:33

Stefan Giudici
2020-01-23 23:00:34

原文網址 Joel Bates
2020-01-23 22:03:29

Just finished my first print. 80 percent Anycubic black, 20 percent Monocure Flex 100. It seems pretty durable with a nice bit of flex in it.

Looks good to me, although it might have spent a minute too long in the curing chamber.

Settings:

Thickness: 0.05

Normal Exposure Time: 15

Off time: 5

Bottom exposure time: 60

Bottom Layers: 10

Any suggestions welcome

翻譯年糕

Richard Humble
2020-01-23 22:29:44

Marcin Bocis
2020-01-23 22:58:22

Richard Humble
2020-01-23 23:16:13

原文網址 Herllon Alves
2020-01-23 21:34:04

Any thoughts on what may have caused this? The arm came out flat, and the base got warped.

I'm using Anycubic clear resin, printing with 45° orientation using these settings:

layer 0.025

exposure time 8

off time 1

bottom exposure 100

bottom layers 8

翻譯年糕

Dyllon Baldock
2020-01-23 21:35:39

Dyllon Baldock
2020-01-23 21:36:46

Gary Bishop
2020-01-23 21:39:28

Herllon Alves
2020-01-23 21:44:51

Gary Houser
2020-01-23 21:52:15

Bob Deblier
2020-01-23 21:53:09

Dyllon Baldock
2020-01-23 21:59:40

Johnny Grant
2020-01-23 22:04:25

David Collinson
2020-01-23 22:50:49

Pataki Ábris
2020-01-23 22:58:17

Ante Ravlić
2020-01-24 00:35:17

Herllon Alves
2020-01-24 00:50:30

Ante Ravlić
2020-01-24 00:57:46

Aaron McCommon
2020-01-24 10:33:19

Herllon Alves
2020-01-25 06:16:19

Herllon Alves
2020-01-25 06:16:47

原文網址 Nicolai Lorenzen
2020-01-23 18:21:39

How does layer thicknes correspon to the rest of the settins with exposure and stuff?

翻譯年糕

Sander van Deijl
2020-01-23 18:25:52

Nicolai Lorenzen
2020-01-23 18:56:45

Nicolai Lorenzen
2020-01-23 19:00:18

Sander van Deijl
2020-01-23 19:10:27

Nicolai Lorenzen
2020-01-23 19:15:55

Sander van Deijl
2020-01-23 19:16:22

Nicolai Lorenzen
2020-01-23 19:16:24

Nicolai Lorenzen
2020-01-23 19:16:31

Nicolai Lorenzen
2020-01-23 19:17:00

Sander van Deijl
2020-01-23 19:18:19

Sander van Deijl
2020-01-23 19:18:39

Nicolai Lorenzen
2020-01-23 19:20:11

Sander van Deijl
2020-01-23 19:22:02

Nicolai Lorenzen
2020-01-23 19:37:43

Nicolai Lorenzen
2020-01-23 19:39:44

Sander van Deijl
2020-01-23 19:41:03

Sander van Deijl
2020-01-23 19:41:21

原文網址 Nicolai Lorenzen
2020-01-23 17:43:40

I own an ender3, and for that machine there are som extensive troubleshooting documents, listing known issues, and ways to try to fix them.

Do we have somthing similar for the Photon?

翻譯年糕

Nipuna Gunarathne
2020-01-23 17:47:29

Nicolai Lorenzen
2020-01-23 17:48:05

原文網址 Jennifer Dawn
2020-01-23 11:16:16

Well, nothing Earth shattering by any means...but I finally made the test print today. I've had this printer for about 2 weeks now. I was so excited to get it and then it came in and I was feeling overwhelmed and intimidated. It was surprisingly easy to setup and get going! I used the Anycubic clear plant-based resin for this.

翻譯年糕

Mike Fatchett
2020-01-23 11:30:14

Jennifer Dawn
2020-01-23 11:34:47

Roldan Kreais
2020-01-23 11:37:20

Brett Vertigan
2020-01-23 11:37:57

Roldan Kreais
2020-01-23 11:39:35

Brett Vertigan
2020-01-23 11:40:32

Roldan Kreais
2020-01-23 11:40:50

Julius EM
2020-01-23 14:45:34

C.K. Lai
2020-01-23 15:03:19

Loren Smith
2020-01-23 15:14:26

Jennifer Dawn
2020-01-23 21:03:59

Alex M Cruz
2020-01-24 00:08:45

Jennifer Dawn
2020-01-24 04:56:21

原文網址 Ben Garbutt
2020-01-23 11:03:49

First print done, detail is a bit rounded, try again with the same model but thinner layers and shorter exposure.

翻譯年糕

Tucker Edward Loper
2020-01-23 12:04:45

Ben Garbutt
2020-01-23 12:10:21

Tucker Edward Loper
2020-01-23 12:10:55

原文網址 Mike Rea
2020-01-23 10:38:57

Anyone have solutions for Chitubox crashing when you try to add a support? I've seen it on a couple of random files, and it doesn't seem to always be on big, complex files.

翻譯年糕

Eric Becker
2020-01-23 10:39:41

Michael Tetreau
2020-01-23 10:40:48

Scott Ball
2020-01-23 10:42:02

Joel Mendoza
2020-01-23 10:48:02

Kevin A Thompson
2020-01-23 10:49:11

Mike Rea
2020-01-23 10:54:55

Michael Tetreau
2020-01-23 10:56:32

全不選發文排行