Anycubic Photon Printer Owners 造訪社團 » Google

I found this google doc for all the recommendations of different resins worth using and the recommended settings. Apologies if it’s been posted before:

翻譯年糕

Random question about Chitubox 1.5. I messed with the hollow option early on, but now it's like, "stuck" on. I used it before my third print, and it did hollow... but it's like that config is now the default. Every time I slice, the hollow popup happens. I've set it to internal hollow at some crazy depth (like 1m) to try to ensure it never happens, but still annoying that it tries. Can't find any documentation talking about this, nor can I find a text config anywhere that defines this particular behavior. No one else seems to mention this online, or my google results are very skewed. Considered uninstalling outright just to get back to default.

Any advice on this? Any preferred alternate slicers? I've been pretty happy with it besides this hiccup.

翻譯年糕

Every print in red is failing like this. Can anyone help? I am using the settings for monocytes red off the Google doc

翻譯年糕

Hi everyone, I have a question: does anyone know what is max temperature of exploitation for FunToDo resin (not IB)

I'm going to print a part that placed close to hot end of FDM printer.

Thanks.

P.S. google didn't help (only provides info about IB)

翻譯年糕

Hi, everyone. I picked up an AnyCubic Photon S this week and I'm running into some failures during my initial prints. Both attempts used the green resin that the printer came with.

The first attempt used settings reported by Daniel Perez on the community exposure settings Google Sheets. ~11 hours.

Layer: 0.02
Normal Exposure Time: 7.5
Off Time: 1.5
Bottom Exposure: 40
Bottom Layers: 8

The second attempt used the default settings. These prints came out slightly better. ~5 hours.
Layer: 0.05
Normal Exposure Time: 8
Off Time: 1
Bottom Exposure: 60
Bottom Layers: 3

Both attempts ended with a small layer of hardened resin on the FEP film. I cleaned everything and re-leveled the build plate in between the two attempts.

Photos shown are from the second attempt. Any advice?

翻譯年糕

Is there a user friendly way/program for adjusting poses on 3D models? I’m google searching but I feel like I’m not using the right words or something in my searches. I have MeshMixer, but either I don’t understand the right tool? Or it’s not mean to move whole limbs and stuff. YouTube tutorials would also be awesome. My Googlefu just seems to be off today. Thanks!

翻譯年糕

Long time listener, first time caller. I am a prop maker in the entertainment industry. I am trying to make a miniature pint glass that is transparent. I have referenced the google spreadsheet for how best to print with the anycubic clear. I have not used IPA to clean and just used soapy water. Then I have sanded to about 2000 grit. I have also tried coating with a clear UV protectant aerosol spray to prevent discoloration. I am struggling with 2 separate issues here. One is the transparency of the print, the second is the yellowing. I have kept them out of sunlight. Any advice is appreciated. Thank you in advance hive mind.

翻譯年糕

Would be grateful if anyone using Anycubic grey would share their exposure settings for 0.05 layer height.

I'm sure it will be suggested, so yes I have tried the resin settings spreadsheet on Google Drive. Although I started off with those settings I found that the normal exposure time of 18 seconds was way to high. I'm working my way through some AmeraLabs calibration files and I'm currently down to a normal exposure of 6 seconds.

Although this does fit a lot better with the suggested exposure times printed on the bottle it does seem rather strange that it's so much lower than those in the spreadsheet.

翻譯年糕

I'm using the Google Doc with the print settings but I'm not sure how much of a difference .35 makes over .5 other than print time. Will you see great detail at lower numbers or less issues etc? I'm looking to maximize the small details on the models I print. As well, do different resins offer different levels of detail? Would other printers (the more expensive ones that use lasers as opposed to the LCD) offer higher levels of detail?

翻譯年糕

Anyone have good settings for Monocure Rapid clear? I tired the top line in the Google sheets and other than the base layers nothing cured. It was a blood bath....

I tried...

.025 layers

9.7 exposure

1.5 off

65.5 base exposure

8 base layers

Epic fail...

翻譯年糕