Anycubic Photon Printer Owners 造訪社團 » SOP

原文網址 이재열
2019-05-03 15:03:41

Not long ago, unfortunately, the Notre Dame Cathedral was burned.
I printed out 3D with a heart of regret and love for the beautiful Notre Dame Cathedral.

Recently, a sophisticated stl file was uploaded to myminifactory, so I downloaded it and printed it out with gratitude.

The downloaded stl file consists of three files.
facade, nave, roof

The output was carried out in the following process.

First, I scaled it so that I could print as large as possible with a photon printer.

To save the resin, each section was hollowed to 1.8 mm.
I made as many drain holes as I could.

I did not rotate each part from the horizontal plane. Because each part does not have a large area attached to the platform, it seems that the main body will not be separated from support.

Support is placed between 1.5 mm ~ 2 mm apart.

The output was very good and the details were very well represented.
I'm very satisfied.

Looking at this 3D model, I hope the Notre Dame Cathedral will be rebuilt as soon as possible.

翻譯年糕

Kelly Rinaldi
2019-05-03 15:20:03

Mikko Asikainen
2019-05-03 15:26:36

이재열
2019-05-03 15:42:33

이재열
2019-05-03 15:42:54

Jacques Abbeels
2019-05-03 16:22:48

이재열
2019-05-03 16:25:29

Roger Miron
2019-05-03 16:39:26

이재열
2019-05-03 16:40:02

Yannick Roget
2019-05-03 17:28:16

Fernanda Carolina Aguiar
2019-05-04 14:24:37

이재열
2019-05-04 16:12:38

Yannick Roget
2019-05-05 01:22:45

Sen Kun
2019-05-05 02:07:16

Jacques Abbeels
2019-05-06 04:54:25

Jacques Abbeels
2019-05-06 05:35:46

Morgan Pierce
2019-08-12 21:40:26


原文網址 Gregorey Savieo
2019-05-01 06:42:49

So I just printed the test lattice cube. It came out really nicely the only thing that sort of bugs me is that it has sort of a white film on it after I cleaned it with isopropyl. Not sure what that's all about

翻譯年糕

Hector Felix
2019-05-01 06:54:13

Gregorey Savieo
2019-05-01 06:54:54

Gon Garcia
2019-05-01 06:55:03

Travis McGeathy
2019-05-01 07:00:15

Gregorey Savieo
2019-05-01 07:01:00

Phillip Burris II
2019-05-01 07:05:35

Wayne Rogers
2019-05-01 07:06:11

Wayne Rogers
2019-05-01 07:37:08


原文網址 Sean Howard
2019-04-30 07:20:41

Anycubic green resin. What is all the white stuff? What did I do wrong?

1) standard print setup in new photon s. Result was pretty green transparent model.

2) rinsed parts in 95% isopropyl. Result was pretty green transparent model. Slightly less sticky.

3) placed in reverse osmosis filtered water in sun for 4 hours. Result is seen below.

翻譯年糕

Dan Hjulberg
2019-04-30 07:42:02

Stefan Giudici
2019-04-30 07:45:06

Nick Williams
2019-04-30 07:49:11

Jon Lamkin
2019-04-30 08:00:46

Sean Howard
2019-04-30 08:07:33

Nick Williams
2019-04-30 08:17:12

Sean Howard
2019-04-30 08:18:47

Nick Williams
2019-04-30 08:19:15

Nick Williams
2019-04-30 08:19:30

Justin Ragsdale
2019-04-30 08:56:35

Nick Williams
2019-04-30 09:06:21

Mark Wardle
2019-04-30 09:19:08

Sean Howard
2019-04-30 09:35:46

Nick Williams
2019-04-30 09:42:46

Ryan Napolitano
2019-04-30 10:05:55

William Charles Chamberlin
2019-04-30 10:44:59

Chris Hunt
2019-04-30 10:55:27

Chris Hunt
2019-04-30 10:57:59

Chris Hunt
2019-04-30 10:58:08

Chris Hunt
2019-04-30 11:00:25

Nick Williams
2019-04-30 11:01:26

Sean Howard
2019-04-30 11:26:33

Chris Hunt
2019-04-30 11:29:03

Chris Hunt
2019-04-30 11:30:38

Sean Howard
2019-04-30 11:31:14

Chris Hunt
2019-04-30 11:31:41

Sean Howard
2019-04-30 11:32:52

Chris Hunt
2019-04-30 11:32:57

Chris Hunt
2019-04-30 11:33:20

Chris Hunt
2019-04-30 11:35:40

Eric Wilfreesboro
2019-04-30 11:57:26

Jaco Norchie Nortje
2019-04-30 12:48:09

David Rodrigues Matos
2019-04-30 13:16:03

Sean Howard
2019-04-30 13:16:26

Robert Cvengros
2019-04-30 14:54:32

Alex Vee
2019-04-30 15:13:34

Alex Vee
2019-04-30 15:14:03

Alex Vee
2019-04-30 15:25:40

Tyson Ryan Valdes Granger
2019-04-30 21:51:03

Eric Wilfreesboro
2019-04-30 22:02:24

Joseph Kason
2019-05-01 08:38:19

Sean Howard
2019-05-01 13:12:09

Sean Howard
2019-05-01 13:12:22


原文網址 Jamie Joules
2019-04-27 19:35:31

Has anyone else noticed a difference in the z axis position calibration needed for various resins?
Previously I was printing with anycubic grey pretty much willy nilly, getting away with build plates that were uneven front to back and with a lot of margin.
When I started working with siraya blu I found I had to have that plate down against the paper to the point where i can't even push the paper in with my fingers right at the point where the paper meets the plate.
I got the technique down with blu so I can print every time now but when I use that same technique for grey I'm getting fails every time.
Could very minor isopropanol contamination and not shaking the bottle on early prints have ruined my grey?

翻譯年糕

Vinicius Silva
2019-04-27 19:40:37

Jamie Joules
2019-04-27 19:41:08

Bob Deblier
2019-04-27 19:44:29

Jamie Joules
2019-04-27 19:45:12

Vinicius Silva
2019-04-27 19:48:51

Jamie Joules
2019-04-27 19:52:13

Richard Shapiro
2019-04-27 20:42:13

Jamie Joules
2019-04-27 21:30:01

Vinicius Silva
2019-04-27 21:36:37

Jamie Joules
2019-04-27 22:27:16


原文網址 Jared Zadorozny
2019-04-15 03:40:44

I think I'm not going to buy clear ever again.

I have great results with it but that's not the problem. The problem is it's invisible I can't tell the difference between resin water or isopropyl droplets on my desk what I really liked about the green is it was very obvious if you got it on anyting. Just feels like a safety hazard especially with how accident prone I am lol

翻譯年糕

Neil Ramsay
2019-04-15 03:43:57

Jared Zadorozny
2019-04-15 03:49:04

Jared Zadorozny
2019-04-15 03:50:12

Neil Ramsay
2019-04-15 03:52:15

Neil Ramsay
2019-04-15 03:53:12

Jared Zadorozny
2019-04-15 03:53:37


原文網址 Victoria Cordani
2019-04-13 11:56:52

Hi, I’m getting my printer on Sunday and I was making sure I have everything ready to go.

As for post processing, is 91% isopropyl alcohol okay to use or is 99% better to use? Thank you!

翻譯年糕

Robert Silvers
2019-04-13 12:00:27

Justin Ragsdale
2019-04-13 12:01:46

Victoria Cordani
2019-04-13 12:02:12

Victoria Cordani
2019-04-13 12:02:16

Dave Smith
2019-04-13 12:44:17

Paul Churchill
2019-04-13 19:03:49

Robb Nunya
2019-04-13 22:32:39

Robb Nunya
2019-04-13 22:32:57

Dominick Trascritti
2019-04-14 06:25:17

Mark Bolding
2019-04-14 11:37:19


原文網址 Wm Kuch
2019-04-07 09:21:49

Hey I made my first print today and I am really happy with this printer. There were a few small issues but I am very happy. But I wanted to share a tip. I got a spray bottle from the hardware store for about $1. I filled it up with IPA ( 90% Isopropyl Alcohol), and to clean the vat I placed the vat above a plastic container are just sprayed it with the sprayer, using a fairly powerful stream. It rinsed ALL of the resin very effectively with no danger of scratching the FEP film. This technique is really good and I plan to re-use the IPA by low-temperature distillation somehow, I'll share those tips when I get it ironed out. Spray bottle is your friend !! Peace :D

翻譯年糕

Richard Humble
2019-04-07 18:31:29


原文網址 Andrew Fudge
2019-04-06 09:16:21

Isoproyl Alcohol. What percent (if it matters) and what's the life like after using it? Can it be re used or is it one bath and done?

翻譯年糕

Richard James Sanchez
2019-04-06 09:18:23

Reynald Lorenzo Dalangin Ilagan
2019-04-06 09:42:03

Ryan Napolitano
2019-04-06 09:46:18

Marnie Jefferson
2019-04-06 09:48:47

Justin Ragsdale
2019-04-06 10:07:24


原文網址 Geoffrey Knoll
2019-03-31 11:04:03

So newbie (just got mine today) question. For cleaning the resin parts when they are done can you use 91% isopropyl alcohol or is something else better?

In addition, are there compiled newbie FAQ for questions like these??

翻譯年糕

Vinicius Silva
2019-03-31 11:06:19

Vinicius Silva
2019-03-31 11:09:03

John Boyington
2019-03-31 11:11:15

Alex Varley
2019-03-31 19:40:21


原文網址 Nick Cassar
2019-03-28 10:22:30

How long should you bathe your print in isopropyl after printing and how long should you cure for under UV Light?

翻譯年糕

Job Moolenaars
2019-03-28 10:26:17

Matthew Brown
2019-03-28 10:42:44

Mark Wardle
2019-03-28 11:00:44


 

全不選 發文排行