Anycubic Photon Printer Owners 造訪社團 » SOP

Hi guys,

I printed some square flat pieces of 3mm thickness (anycubic red resin) and some corners are slightly bent, do you know why?. I cleaned them with isopropylic alcohol and also did U/V bath to harden.

Exposure time was 9 seconds per layer, every print was completed in only 20 minutes or so.

I tried to immerse pieces in hot water (really hot) and they became soft so I pushed them against flat surface and wait to cool but no success, after some time corners bend again.

My printer platform is flat, I printed other pieces without problem.

翻譯年糕

Hi all. Just ordered my Photon and am curious, how much Isopropyl alcohol do you usually spend?
It's quite expensive here in Sweden, about $20 per liter.

翻譯年糕

So I accidentally spilled some resin on my right half of my right hand. Cleaned it off immediately with paper towel and 99%isopropyl alcohol, then washed my hands a couple of times then soaked my hands in isopropyl alcohol while rubing the areas of the spill and washed off my hands again. I have a 1/10 burning ish sensation but nothing serious. Will this get worse ? is there anything I can do ? It was the Anycubic photon black resin.

翻譯年糕

hi ,one noob question the vat is cleaned also with alcohol isopropil or similars?

翻譯年糕

Hi Everyone. Took Delivery of a Photon on the weekend, coming from the world of PLA, the quality on this thing is mind blowing.

My first print with the turquoise resin was awesome. I did a second print using the grey resin that came with it, and it was a little disappointing.

Full disclosure, I couldn't get hold of isopropyl alcohol, so I used what showed as the closest thing on Google which was Boots Sterilising liquid. It was fine on the first print, but the second print looks like it has pitting in a few spots on the surface. I didn't notice if it was there before I cleaned the print, so now I'm at a loss as to whether it came off the printer like it, or if the cleaning solution I used caused it.

Generally, what causes pitting in resin prints? Do I have to really, REALLY, shake the resin before I fill the bath, or is a gentle shake enough?

翻譯年糕

What is IPA, im assuming its isopropyl alcohol? and whats the difference between that and Monocure's ResinAway? Are they 2 completely different substances? or is it just tomahto , tomayto?

翻譯年糕

Ok, so im going to pull the trigger and order me a photon, any extras i should get with it? like anything that is good to have that doesnt come with it? (the amazon one looks like it comes with a bunch of little stuff, scrapers, gloves and some resin) also going to order a 1L bottle of monocure clear, 1L bottle of Isopropyl (resinaway is not available), a uv lamp to cure the prints and and a 6pack of fep film 5mil thick. Anything else that one would suggest for a first SLA printer?

翻譯年糕

After 5 or 6 months of storage in the vat, covered in a thick jacket and red windows (completely out of contact with light ). My white resin has begun to curing and and it is split into two parts, the top is transparent resin and the bottom is white. It still prints well, but just very difficult to clean the model with isopropyl.
So I think it might be that the air has caused my resin to cured ?

翻譯年糕

Which product can I replace isopropyl alcohol in the cleaning of the parts?

翻譯年糕

Hi everyone. Been amazed with the printer. Printing last night. Didnt print .took tray out and resin all over glass.Theres a small split in the film any ideas what could cause it. Not been caught or dropped.got nearly all resin of glass with isopropol and tissue.

翻譯年糕