Anycubic Photon Printer Owners 造訪社團 » PID

Two questions for you all with more experience.

1: Is there a resin that cures a little closer to say forgeworld/gw resin models? A little more soft when going at it with an xacto?

2:Can some of you share your support settings? I am using Chitubox(I know Prusa is highly recommended but I have yet to figure it out haha). I was tinkering with my settings and now my supports seem to be leaving a little bit larger marks to clean up, hoping someone has some good suggestions. I mainly use Elegoo 3d rapid Grey(is this also what everyone refers to as Elegoo Grey or are there two versions?) and have two bottles of Siraya Tech Blu to try, if the resin types matter.

Thanks!

翻譯年糕

any good reviews for the anycubic rapid resin skin .. or any other color?

翻譯年糕

Conception to finish.
Making some parts for a Star Wars Nerf Blaster mod Using the power pack model from an E11 (Flywheel cover for a Nerf Rapidstrike)

STL was based a couple of heavily modified files from Thingiverse.
(E11 Stormtrooper Blaster and a Rapidstrike motor cover)

Printed in Siraya Blu.
Then Primed, sprayed in car body work silver, then resprayed in Matt Black using Copydex to mask off where the paint chips should be.

翻譯年糕

So... Stupid me forgot to remove supports of previous print (just pulled the printed part off) and well it punctured my vat. With result I got a little print on my LCD screen that is quite thin and doesn't come off that easily.

Any one else had a similar problem? And what to do so I don't damage my screen in the process?

翻譯年糕

Test with the last of the black, clear, and a touch of the Monocure rapid flex was a complete success.

Giving it a few minutes in front of the lamp, and will check that out does have a little flex to it.

翻譯年糕

28mm Panzer I A tank printed with Monocure Rapid Grey. Haven't decided which turret I'll use yet. Also sneak peak of the diorama base it'll live on.
https://www.wargaming3d.com/product/panzer-1-a-28mm/ 翻譯年糕

I'm stumped. I keep getting this mass on the build plate side of my print. It's like its curing just that area the whole way up. But I did a dry run with paper and did not see anything that would have made this cure like this. I've tried 3 different d20 files. Please help. As you can see the rest of the print comes out flawlessly.

Also I've moved this to multiple locations on the build plate with the same results. I just dont understand.

Monocure rapid 3D clear

翻譯年糕

Looking for some resin recommendations. I have so far used the Anycubic Clear Green and the Elegoo Grey rapid 3d. Loved the green but it was a bit brittle. The Grey has been a bit touchy still working on settings. But I am doing an Amazon order for some other stuff figured I would add some more resin to the arsenal.

翻譯年糕

Has anyone used the Elegoo 3d rapid blue resin? What were your settings on your photon if you've had success? It doesnt seem to be on the usual google doc spreadsheet that i can see

ELEGOO ABS-Like 3D Printer Rapid Resin LCD UV-Curing Resin 405nm Standard Photopolymer Resin for LCD 3D Printing 500Gram Blue

翻譯年糕

Hi All,

Bought my Photon in November last year from AnyCubic's eBay store. It sat in its box in my office until this last weekend when an opportunity presented itself to create something.

Unboxed it, set it up following the instructions and all was well apart from the plate not tightening up and when I tried to use it the USB port wasn't working.

Contacted Anycubic, Then found this site and the comments about the plug falling out of the motherboard during transit. Opened her up and sure enough that was the issue. Plug back in and USB stick is readable. So cancelled that ticket with Anycubic :-)

Dismantled the print plate to find the reason the grub screw was't working was there was already one deep in the hole.! Using that one the head could be levelled and locked in place. :-)

However. Now the unit wasn't working at all. Z-axis jammed stationary but making a motor drive noise like it was trying, fans not working and main LCD dead.

Contacted Anycubic (again) and their customer support have been extremely rapid and helpful. Sent me a print to run that generates a diagnosis file. When I sent it to them they assessed it as a faulty motherboard.

Asked for my delivery details for a replacement which I gave them and got a message today saying its on its way to me.!! The tracking info they gave me suggests its coming from local so fingers crossed unit will be all fixed and running very soon.

Bob

翻譯年糕