Anycubic Photon Printer Owners 造訪社團 » 用戶發文

Makers,

I just recieved a batch of new resins since I was fed up with my Monocure Rapid Clear I just could not get to work...

Can anybody point me to a good "Benchy'esque" model for the Photon? To etermine whether the settings are on spot before I start a 7 hr print just to fail?

Cheers

翻譯年糕

Makers, I need help.
For ages I couldn't get a working print out of my machine anymore.
I use Monocure Rapid Clear, a new Fep and the bed has been perfectly leveld a minute before starting the print. The Screen works flawless also, at least the test triangle I was checking jesterday, prior to the print.

I was Slicing with ChiTu Box for the first time here, but my attemts with the original slicer didn't work any better lately. I was orienting my settings on this Video:
https://www.youtube.com/watch?v=9H3unWZZKjM&t=170s

Layer Hight: 0,05
Bottom Layer: 10
Exposure Zime 14
Bottom Exp. 90

Before that I tried different values on the Excel ( https://docs.google.com/…/1crvzMnt_8NJXAsABinoIhcOjE8…/edit… ).

Non really worked. Sometimes it was just a flat mass on the fep, sometimes the print looked good to a certain point but then looked like an deflated baloon. Simmilar to the Pillar mini below.
This time I had one good model (which showed some wired kind of flash thoug, I never experienced that before) and one messed up (The pillar Model).

Please can somebody tell me what I am doing wrong???

翻譯年糕

A few days ago I saw somebody post a picture of a very full buildplate, stating they used a program that would by itself place the parts on the build plate and orient it.
Can somebody point me to that programm?

翻譯年糕

Guys 'n Gals,
I have a problem. Its been a while that I got a good print out of my photon. Right at the start it worked like a charm, now it just doesn't and almost every print has some failure on it.

Current print is attached below.
Its Monocure Rapic clear.

Settings:
-------------
Layer: 0,025
Norm. Ex.: 9,7
Bottm Ex.: 65,5

Resin on Room temperature.

Slicer had the Model angled, Medium Support (Full) and manual support added where islands where probable.

Fep was changed yesterday, printer was leveled last print.

Can you make out any solution from these data and pictures guys? My misprints are starting to become very costly... :-(

翻譯年糕

Anybody capable of felting we what my issue is and how I can fix that? :(
Monocure Rapid Clear, Spreadsheet Settings for 0.05 mm.

翻譯年糕

Goup, I'm getting a bit frustrated.
First 2 Pictures where my first aatempt (0,02). Since it failed I tried again with 0,05 Layer thickness, using the numbers from the spread sheet (Monocure Rapid Clear):
norm. exp.: 1, Bottom 40. Bottom Layers 10. As you can see in the latter pictures, it still failed. Last pic is how it SHOULD look. I'd rather use 0,02 than 0,05, but I can't get anything to work anymore :-(
Can you please help me adjust my settings?

翻譯年糕

What is causing this loosening from the build plate? I am pretty sure my leveling is spot on. Over- / undercuring?

翻譯年糕

Guys, I was using the Monocure Rapid Clear on a current print. I used Anycubic's Auto Support (Middle-Strenght) but can not give you the exact (!) Settings I used.
I was going for 0,02 layers (Anycubic Photon) having an exposure time between 9 and 10 Secondsfor the normal layers and between 40 - 60 sec. on the 8 Bottom layers. Which shall be irrellevant for the bottom Layer was ok.

HERE is my problem:

This morning I woke up to a failed print. The Bottom Layer was stiking to the plate nicely but ON the Bottom layer where only some supports growing. The main print however, must have fallen off the plate and layed in the basin. This must have happened pretty early for it was but a flat surface on the basins ground. Not a partial Print.

I wonder whether you could give me advice how to adjust my times.

I was using pretty much the data from the Document (excel)

However, I had a rest of anycubic green in the basin which mixed like 50/50 with the Rapid Clear. I DID have successfull prints with this exact mixture in the basin, though smaler.

Thank you for your help

翻譯年糕

Question time. I mixed an approx. equal amount of Monocure Rapid Clear with the remaining Anycubic Green, the photon comes with.
In my slicer I used the same properties as I did with the (pure) green.
I woke up to a failed print (photo). It's the biggest print I attempted so fast though. The slide solid have been as higher than than that also.

A) why didn't the printer complete the full print, or art least go through the file as if it would work. It stopped midway through

B ) should I change settings (how) if I mix Anycubic Green to Rapid Clear? How so, compared to the profiles for either green or clear?

Thank you

翻譯年糕

I am shure all of you have noticed that second screw hole on the Building Platform, right in front of the hole for the big red tightening screw...

Any ideas what that little **** is for? I Accidentally screwed the Tightener in that hole which resulted in an horribly failed print since the Platform just slid off the axis.

---Edit---
I've been thinking about this question for a few moments and I can now fully comprehend how stupid it was. I thought maybe I should delete the post (against the background of the love you swung at me) but then decided to leave it for the groups general amusement and as an example for the occasional cognitive obfuscation of some users (a.k.a.: me).

Have a great day ?

翻譯年糕