Anycubic Photon Printer Owners 造訪社團 » 用戶發文

My last two prints have resulted in no print whatsoever. I believe it is still level (using Flint Read s video) and used the correct settings ( per flints suggestions which were working at one point) for the resin that comes with the printer. Any idea what the issue is?

The screen still seems to be working, but the resin was sitting in the vat for a few days.

It was printing fairly well and now is just not sticking to the build platform

翻譯年糕

Alright, so life got busy for a bit so I had to take a break from learning how to properly use my Photon.

So I am doing some more test prints with multiple pieces on the build plate at the same time. Some of my prints are sticking while some are not. I can't figure out what the problem is, any likely issue I am entirely missing?

**the build plate is level**

翻譯年糕

One of my last prints was with some tokens. Per some suggestion from others here I printed the tokens without supports which did fix the bubbling support issue. However, I have now noticed that the tokens are not completely straight when you hold them up to your eye. Is this from the Z axis wobbling, the machine itself not being level, or possibly the build platform off level? I followed Flint's vid about leveling which appeared to fix the issue for other prints and it feels firmly in place so I am thinking it is more the machine itself is off tilt because of the dumb apartment I live in. Any possible insight from others running into the same problem?

翻譯年糕

Hey everyone, so I am trying to print some tokens but I am really running into problems. I am attempting to print 12 tokens but only the middle row is sticking on the supports. The four however are also coming out warped and not flat as they were designed. I have attempted this twice thinking there was a problem the first go around.

I have cleaned the vat, but it still keeps happening. Any clues?

翻譯年糕

This is the results of my 8th print I think. Second successful lol. I possibly had an issue with my screen so I strategically placed everything you see here so that I could see where the problem may have been.

I can see a few imperfections but overall I am happy to have so many things printed all at once.

翻譯年糕

Maybe this is silly, but when the preview of your print is yellow is it bad? I noticed the print in the top left failed earlier, yet the one on the right was successful completely. The difference being the design is blue while the supports are yellow, yet the top left is entirely yellow. Does this mean anything?

翻譯年糕

Finally got my first print successfully made last night thanks to Flint Read . So I decided to try another small print of something else but didn't change my settings at all. This was the unfortunate result...the whole front half just didn't print. It was a complete clean cut up the front half and only printed the back. Anyone know why?

翻譯年糕

Is there a good guide about how long we are to cure our prints?

翻譯年糕

Hey everyone,
So I am on my fourth attempt at a print today. The first attempt had supports on the build platform, but not my build. The last three attempts have produced nothing. Zero. Nada. There is nothing in the build platform, however, I did take out the resin chamber to adjust the build platform as I noticed it wasn't completely straight when I looked down on it. I saw that there was a small pool formed on the very bottom of of the resin chamber that resembled the raft but it was super thin and my gloved finger couldn't really feel it.

As for my prints, I have adjusted settings to what other members have suggested such as Flint Read which makes me think the issue is me. 3 of the four prints were a small miniature I found on thingiverse while one of the prints was the cube that comes on the flash drive (that was my second attempt). I am at a loss for what I am missing, would really appreciate someone pointing me in the right direction...

翻譯年糕

Alright, so continuing to learn from my failed first attempt.

I am using Anycubic Green and these are my settings that I have adjusted after speaking with a different user here in the group. Does anyone see anything that is wrong before I start to print?

翻譯年糕