• 3D列印服務
  • COSPLAY 3D 建模
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Kyle Standring
2019-07-25 08:38:33

Anyone have the link to proper replacement screens handy?

翻譯年糕

Bob Deblier
2019-07-25 17:11:40

Bob Deblier
2019-07-25 17:13:28

Kyle Standring
2019-07-26 01:01:35


原文網址 Kyle Standring
2019-07-10 06:34:16

Trying Danny Lloyd ’s 85/15 elegoo grey and mono cure flex, any thoughts on exposure would be great, hope the pics are ok, they’re all of same test just different angles and flash/no flash

翻譯年糕

Bob Deblier
2019-07-10 14:21:26

Kyle Standring
2019-07-10 14:28:36


原文網址 Kyle Standring
2019-07-07 10:53:24

My front panel doesn’t seem to want to go back on flush and line up with screws, any tips or tricks for this

翻譯年糕

Spencer Bartley
2019-07-07 11:00:46

Kyle Standring
2019-07-07 11:03:18

Chad Elstad
2019-07-07 22:12:28


原文網址 Kyle Standring
2019-07-07 09:34:01

Hey all, my z rod came off during a print ? trying to get it back into place, anyone know the procedure here?

翻譯年糕

Trevor McIntosh
2019-07-07 09:35:43

Derek Reihe
2019-07-07 09:55:28

Kyle Standring
2019-07-07 10:48:56

Derek Reihe
2019-07-07 11:00:17


原文網址 Kyle Standring
2019-06-06 10:13:06

Had to mess with something inside the photon and the lcd display ribbon came loose, and I can’t seem to get them back in. In a video I watched it looked like you press the sides of the clips to get them back in but I can’t seem to get it. Any help would be great

翻譯年糕

Dylan Sawatzky
2019-06-06 10:36:07

Dylan Sawatzky
2019-06-06 10:38:20

Kyle Standring
2019-06-06 11:15:40

Kyle Standring
2019-06-06 11:43:36

Dylan Sawatzky
2019-06-06 12:09:24

Kyle Standring
2019-06-06 12:52:11


原文網址 Kyle Standring
2019-02-28 11:46:36

Has anyone looked at the Mayku Form Box as an alternative to normal RTV?

翻譯年糕


原文網址 Kyle Standring
2019-01-10 06:31:52

looking for some advice on orientation/supporting this model, ive tried printing it flat to bed but got some warping, and printed at angle and got warping along the bottom closest to bed. The back will not be seen so heavy supports on the back side are a possibility, thanks for any help!

翻譯年糕

Eric Jensen
2019-01-10 06:48:01

Ricky Chavez
2019-01-10 09:43:16

Mark Wardle
2019-01-10 15:19:05

Mark Wardle
2019-01-10 15:19:37

Kyle Standring
2019-01-10 15:45:41


原文網址 Kyle Standring
2018-07-06 12:17:32

Any idea what causes cracks like this? This is pre cured

翻譯年糕


原文網址 Kyle Standring
2018-06-29 08:06:38

So Ive been advised by Anycubic to loosen the Z motor screws 1/2 - 1 turns as a fix for Z Wobble. Are these the same screws i messed with for the Z Wobble fix? Or different? any tips, pics or info would be great, thanks!

翻譯年糕


原文網址 Kyle Standring
2018-06-28 07:09:59

Hey everyone,

I keep getting this on my prints, it looked like Z Wobble so I did the fix from Anycubic on YouTube and reassembled and the problem persists. Should I attempt the fix again or could it be something else? The Resin is monocure rapid grey

翻譯年糕


 

討論主題

全不選 常用關鍵字