Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Evan Hedges
2019-02-06 01:49:42

Hey. So I’m about to use ChiTuBox for the first time. Is light off delay the same as off time in the anycubic slicer?

翻譯年糕

Sen Kun
2019-02-06 02:04:22

Evan Hedges
2019-02-06 02:19:24

Alwin Chan
2019-02-06 03:17:46

Sen Kun
2019-02-06 03:27:14

谢信福
2019-02-06 17:42:35

Sen Kun
2019-02-06 18:10:52

谢信福
2019-02-06 18:29:43

谢信福
2019-02-06 18:29:51

Sen Kun
2019-02-06 18:31:36

谢信福
2019-02-06 18:37:15

原文網址 Evan Hedges
2019-02-02 10:38:07

Came out nice!

翻譯年糕

Nic Lim
2019-02-02 19:46:57

原文網址 Evan Hedges
2019-01-29 02:04:15

Hello again. So I have had this problem. The my screen ratio just doesn’t seem to work no matter what settings I try on my display.

翻譯年糕

Sen Kun
2019-01-29 02:13:28

Aiden Sone
2019-01-29 02:16:33

Kevin Rank
2019-01-29 02:20:00

Evan Hedges
2019-01-29 02:21:26

Marcello Ganzerli
2019-01-29 02:25:33

Evan Hedges
2019-01-29 02:41:00

Aiden Sone
2019-01-29 02:44:16

Kevin Rank
2019-01-29 02:45:25

James Twohey
2019-01-29 06:00:17

Stephen Burrows
2019-01-29 11:49:13

谢信福
2019-01-29 12:48:55

谢信福
2019-01-29 12:49:05

James Twohey
2019-01-29 13:44:35

Jawad Abuasabeh
2019-01-30 20:17:11

谢信福
2019-01-30 20:40:48

Jawad Abuasabeh
2019-01-30 21:05:49

原文網址 Evan Hedges
2019-01-08 21:56:24

Hey everyone. So last night I had a little leak. There is some cured resin on the lcd glass. Is it possible to remove it? Or do I need to replace the glass?

翻譯年糕

Dániel Vœlkel
2019-01-08 21:57:13

Susan Sioux Mercer
2019-01-08 21:57:25

Peter Ede
2019-01-08 21:57:45

Dániel Vœlkel
2019-01-08 21:58:38

Evan Hedges
2019-01-08 22:00:25

Chris Marshall
2019-01-08 22:04:18

Peter Ede
2019-01-08 22:06:44

Evan Hedges
2019-01-08 22:14:31

Ivo Mavrodinov
2019-01-08 22:24:06

Sen Kun
2019-01-08 22:27:50

Mike Cousins
2019-01-08 22:39:10

Mark Wardle
2019-01-08 23:06:50

Ricardo Sebastian Ibacache Guerr
2019-01-09 03:42:50

Patrick Smith
2019-01-09 04:30:04

Kevin Rouviere
2019-01-09 04:38:34

Kevin Rouviere
2019-01-09 04:38:49

原文網址 Evan Hedges
2018-12-10 11:36:46

Hello everyone. Just got the anycubic photon. It’s a great printer. But I’ve been have this new issue after 3 very successful prints. I have tried everything. Re level new fep film different exposure settings etc. it prints the raft and supports fine. However the model never seems to stick to the supports. Could this be a usb issue?

翻譯年糕