• #maker+t=market
  • 3D列印服務
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Michael Muir
2019-02-09 23:19:25

I didn’t waste a single millimeter on this print

翻譯年糕

Günter Praschberger
2019-02-09 23:26:04

Joel Le Noir
2019-02-09 23:38:46

Richard Shapiro
2019-02-09 23:39:22

Erdian Madskin
2019-02-10 00:12:28

Jamie Joules
2019-02-10 00:17:12

Tim Grünewald
2019-02-10 00:24:26

Michael Muir
2019-02-10 00:29:26

Tim Grünewald
2019-02-10 00:29:56

Michael Muir
2019-02-10 00:33:51

Tim Grünewald
2019-02-10 00:35:45

Tim Grünewald
2019-02-10 00:36:16

Tim Grünewald
2019-02-10 00:39:42

Michael Muir
2019-02-10 00:42:40

Chris Sutherland
2019-02-10 00:46:20

Jeffrey Rodriguez
2019-02-10 03:15:59

Michael Muir
2019-02-10 03:17:03

Jeffrey Rodriguez
2019-02-10 06:31:12

Michael Muir
2019-02-10 08:06:22

Matt Mason
2019-02-10 08:49:13

Peter Ede
2019-02-10 12:24:28

Brian Petersen
2019-02-10 15:43:07

Michael Muir
2019-02-10 22:35:55

Michael Muir
2019-02-10 22:36:17


原文網址 Michael Muir
2019-02-02 00:15:39

I’m looking for some help with filtering the resin fumes from someone who knows more about the photon than I do. I’d like to build an acrylic cover to set over the printer with a fan, duct, and filter built in to vent out the window. My question is, will this affect the internals of the printer? Some people have mentioned some filtering setups work against the internal fan for the LCD/motherboard. Also what is the best type of filter for this setup, just a standard activated carbon filter?

翻譯年糕

Dylan Hancox
2019-02-02 00:16:39

Nick Porterfield
2019-02-02 00:20:08

Tony Luong
2019-02-02 12:30:21

Nick Porterfield
2019-02-02 23:07:47


原文網址 Michael Muir
2019-02-01 06:14:42

I recently switched to chitubox and I’m loving the quality of my prints and how much easier support clean up is with contact spheres. These parts require minimal clean up, especially after filler primer

翻譯年糕


原文網址 Michael Muir
2019-01-25 07:27:20

Okay I give, I have to consult the hive mind on this one. I’ve had my photon for a few weeks and have got some good prints off it but I have a small reoccurring problem, my FEP seems to get just a layer or two of a small section of my prints every time I run the printer. Area that gets this is completely random. I’ve been through three FEP films and each time the same thing happens. The layer is too thin to actually get off of the FEP, I’ve tried everything from soaking isopropyl in it to gently scraping at it with a palette knife. It’s happened with the green included with the printer and with the maroon and black AC resins. I’ve also ran the exposure test on all of the resins and I’m fairly confident I have the exposures set right otherwise I’d assume my issue is under exposure. After my third FEP replacement I decided to ignore it and it backfired, the FEP tore on my last print right on the spot of one of these “layers” and leaked resin onto the screen. Anyone had issues like this or have any advice as to what this is? Setting for the print that caused the rip:0.025mm, 14s, 95s in the black AC resin

翻譯年糕

Michael Muir
2019-01-25 07:30:59

Ken Pooley
2019-01-25 07:54:54

Richard Shapiro
2019-01-25 08:05:13

Terry Reed
2019-01-25 08:52:34

Ken Pooley
2019-01-25 10:32:27

Ken Pooley
2019-01-25 10:35:04

Ken Pooley
2019-01-25 10:40:19

Sen Kun
2019-01-25 16:35:14

Sen Kun
2019-01-25 16:40:54

Michael Muir
2019-01-25 20:15:29

Michael Muir
2019-01-25 20:48:09

Sen Kun
2019-01-25 21:58:21

Michael Muir
2019-01-25 23:15:34

Philippe Maegerman
2019-01-26 02:24:12

Philippe Maegerman
2019-01-26 02:25:10

Michael Muir
2019-01-26 02:27:07

Ken Lim
2019-01-26 09:17:24

Ken Pooley
2019-01-26 11:24:32


原文網址 Michael Muir
2019-01-23 08:33:46

Mikko Asikainen
2019-01-23 14:33:06


原文網址 Michael Muir
2019-01-08 05:22:08

The results of my first few days with the photon, I’m impressed. The left was printed with Anycubic black and the right was Anycubic maroon. I noticed the maroon was more prone to air bubbles forming in some of the layers which was a little strange but otherwise both resins worked pretty well. Both models also have a layer of primer over them

翻譯年糕


 

討論主題

全不選 常用關鍵字