Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Will Koone
2019-06-08 21:27:25

Had a thought after I didn't tighten down one side of the vat.

More expensive SLA printers have a peel mechanism, usually just tilting the vat as the bed peels away. Thus reducing peel forces.

With a little mod like hinging one side of the vat and a stop on the other to allow it to lift a little, it'd create the same kind of incremental peel a tilting vat has as the bed pulls away. Probably need to increase the lift distance a little, but that's the only software change I can think of, and the only hardware would be the two fingers the vat slides under being swapped out.

Obviously overfilling the vat would be an exceptionally bad idea with that setup. It *shouldn't* effect print accuracy if everything returns to its original position.

Good idea or waste of effort?

翻譯年糕

Stefan Giudici
2019-06-08 21:30:38

Ben Price
2019-06-08 22:15:19

Richard Shapiro
2019-06-08 22:20:15

Stefan Giudici
2019-06-09 03:12:30

原文網址 Will Koone
2019-05-26 08:57:30

I was thinking zwob but the lines are only on the flat surface. The cylinders seem to be unaffected. Any ideas?

翻譯年糕

Jarrod Smith
2019-05-26 09:15:11

Will Koone
2019-05-26 09:31:15

Will Koone
2019-05-26 09:36:38

Vinicius Silva
2019-05-26 09:41:56

Will Koone
2019-05-26 09:43:10

Sen Kun
2019-05-26 14:26:35

原文網址 Will Koone
2019-05-26 06:30:54

Well that sucks.

嗯, 那糟透了.

· 查看原文 · 為此翻譯評分

原文網址 Will Koone
2019-05-24 21:56:18

After disassembling and cleaning the ball joint of my build plate and squaring my zrail it seems my 0 position is above my home position. Shouldn't it be blow the home position? Because now when I start a print it'll home, put some pressure on the LCD and fep enough to torque the z rail back slightly then go to zero and print just fine. (3 prints like that so far)

翻譯年糕

Philippe Maegerman
2019-05-24 22:04:15

David Nicholls
2019-05-24 22:54:00

Will Koone
2019-05-24 23:01:05

原文網址 Will Koone
2019-05-19 21:52:14

Question swelling of parts on long exposure time. The swelling would only occur in x & y yes? Giving the classic "elephants foot" on initial layers but shouldn't affect z because it's constrained by the plate and the fep. Am i thinking about that correctly?

翻譯年糕

Devin Wallace Simonsen
2019-05-19 21:55:50

Will Koone
2019-05-19 22:02:18

Fred Breton
2019-05-19 22:06:19

Devin Wallace Simonsen
2019-05-19 22:09:17

Will Koone
2019-05-19 22:12:13

Richard Shapiro
2019-05-19 23:04:18

Will Koone
2019-05-19 23:10:35

原文網址 Will Koone
2019-05-19 09:45:22

I think my build plate shifted just a little. Second time in a row.

翻譯年糕

Richard Shapiro
2019-05-19 09:52:11

Michael Szita
2019-05-19 09:57:51

Will Koone
2019-05-19 10:05:30

Adam Musgrove
2019-05-19 10:09:19

Will Koone
2019-05-19 10:26:49

Daniel Velarde Kübber
2019-05-19 10:27:52

Chad Elstad
2019-05-19 10:27:55

Daniel Velarde Kübber
2019-05-19 10:28:12

Will Koone
2019-05-19 10:32:58

Steven Tooze
2019-05-19 10:58:41

Patrik Olsson
2019-05-19 13:26:51

Robert Becke
2019-05-19 13:59:05

Robert Becke
2019-05-19 14:01:14

Alexander Mihailov
2019-05-19 18:43:52

Sébastien Guilbaud
2019-05-19 20:05:35

Derek Reihe
2019-05-19 21:24:53

Tiago Duarte
2019-05-19 21:26:05

Sébastien Guilbaud
2019-05-19 21:33:14

Chris McGowen
2019-05-20 14:57:04

Jose Elizondo
2019-05-21 08:33:40

原文網址 Will Koone
2019-05-13 04:38:54

Probably ought to check my support settings but, it worked.

翻譯年糕

原文網址 Will Koone
2019-05-10 10:31:37

Anyone have good settings for Straya Blu at .01mm?

翻譯年糕

Richard Shapiro
2019-05-10 10:33:07

Bob Deblier
2019-05-10 10:33:55

Richard Shapiro
2019-05-10 10:34:01

Richard Shapiro
2019-05-10 10:35:07

Milton Maxson
2019-05-10 10:37:25

Will Koone
2019-05-10 10:38:52

Chris Rees
2019-05-10 10:41:45

Richard Shapiro
2019-05-10 10:43:37

Chris Rees
2019-05-10 10:50:07

Richard Shapiro
2019-05-10 10:51:56

Richard Shapiro
2019-05-10 10:52:04

Will Koone
2019-05-10 10:56:03

Richard Shapiro
2019-05-10 11:20:32

Will Koone
2019-05-10 11:27:30

Richard Shapiro
2019-05-10 11:38:42

Guti Gutmann
2019-05-10 14:49:23

Robert Thorhauer
2019-05-10 17:06:37

Richard Shapiro
2019-05-10 21:29:43

Robert Thorhauer
2019-05-11 00:27:30

原文網址 Will Koone
2019-05-03 00:21:03

Rando pie in the sky thoughts:
Would it be possible, perhaps with a firmware and file format change, to pause a print and change exposure times on the fly? Like for swapping vats to print in another color the way we've done with swapping filaments onFDM printers.

Obviously resins with similar times wouldn't need the time change but if say I wanted a strong base in Blu but a flexible top out of Flex? (Or flex in the middle with Blu end caps) Could open up a whole new world of designed products.

翻譯年糕

Jarrod Smith
2019-05-03 00:35:28

Milton Maxson
2019-05-03 00:39:11

Will Koone
2019-05-03 00:40:22

原文網址 Will Koone
2019-04-30 08:38:13

First print with Siraya tech blu, and The 3D club FEP.

翻譯年糕