Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Paul Churchill
2019-03-24 00:21:36

This is running on older printer whilst i await new printer main board... this is with the new firmware... its so much quieter and also the timings on the screen are much closer to real time now... Anycubic White..

This is 1:148 Scale..

翻譯年糕

Vincent Bogers
2019-03-24 01:17:10

Paul Churchill
2019-03-24 01:30:55

David Weller
2019-03-24 01:45:23

Mihai Cernatescu II
2019-03-24 06:51:32

Mitchell Kruik
2019-03-24 19:09:09

Richard Wilson
2019-03-24 19:19:07

Paul Churchill
2019-03-24 21:39:07

Richard Wilson
2019-03-24 22:20:56

Paul Churchill
2019-03-24 22:40:18

原文網址 Paul Churchill
2019-03-22 01:46:09

I just received this through the post.... all my other bottles have been a brown colour, is this old stock does anyone know?
Thanks

翻譯年糕

Giuseppe La Capra
2019-03-22 01:50:11

Jarrod Smith
2019-03-22 01:50:55

Kieran Winsper
2019-03-22 01:50:56

Paul Churchill
2019-03-22 01:53:59

Jarrod Smith
2019-03-22 01:57:22

Giuseppe La Capra
2019-03-22 02:01:39

Jarrod Smith
2019-03-22 02:03:39

Giuseppe La Capra
2019-03-22 02:04:32

Giuseppe La Capra
2019-03-22 02:05:02

Jarrod Smith
2019-03-22 02:07:53

Sen Kun
2019-03-22 02:28:20

Mike Michaels
2019-03-22 02:56:58

原文網址 Paul Churchill
2019-03-18 03:00:06

Can anyone tell me why autosupport in the photon slicer is just putting these puny supports on pls? :)

翻譯年糕

Glenn Mcfadden
2019-03-18 03:03:36

Paul Tyer
2019-03-18 03:15:25

原文網址 Paul Churchill
2019-02-22 20:04:04

Question for you...
So tried to perform the resin test this morning,
Followed instructions and enabled the test gcode file it bleeped and said complete then tried to run the 005 resin curing test file from gib hub, it just bleeps and does nothing! Where am i going wrong ?

翻譯年糕

Che Fielding
2019-02-22 20:36:01

Paul Churchill
2019-02-22 21:14:08

Paul Churchill
2019-02-23 00:47:53

Paul Churchill
2019-02-23 02:33:21

Paul Churchill
2019-02-23 02:34:58

原文網址 Paul Churchill
2019-02-20 17:04:01

Has anyone ever returned to the printer when its finished a job to find a load of resin has somehow cured itself to the top of the build plate!??? Never seen that before!...

翻譯年糕

陳彦廷
2019-02-20 17:52:30

原文網址 Paul Churchill
2019-02-18 07:09:43

Hi all, what would cause models that have printed well before (same file) to now end up with holes in the walls when printed? Is this a screen issue and if so how would i check please?
Thanks

翻譯年糕

Paul Churchill
2019-02-18 07:11:45

Peter Ede
2019-02-18 07:14:35

Paul Churchill
2019-02-18 07:15:25

Peter Ede
2019-02-18 07:17:14

Paul Churchill
2019-02-18 07:17:50

Peter Ede
2019-02-18 07:20:38

Paul Churchill
2019-02-18 07:21:12

Peter Ede
2019-02-18 07:26:01

Paul Churchill
2019-02-18 07:26:20

Paul Churchill
2019-02-18 07:27:28

Alex Vee
2019-02-18 15:48:45

Paul Churchill
2019-02-18 16:13:58

原文網址 Paul Churchill
2019-02-01 21:56:46

Hi from a relatively new owner!... can someone point me to a fix for small models curling up at the edges when printed please, tried a few different support types but still get the same unevenness

Many thanks

翻譯年糕