Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Peter Lynn
2019-07-06 09:22:03

Just updated firmware on the photon what is a good setting for anti aliasing to remove layer lines more.

翻譯年糕

Timmo Hellemann
2019-07-06 09:32:03

Trea Cotton
2019-07-06 14:47:29

Michael Van Kesteren
2019-07-07 17:07:46

Michael Van Kesteren
2019-07-07 17:08:24

原文網址 Peter Lynn
2019-07-04 07:31:06

Inkbird 308 and two x 5 watt heat pads.

I'm doing things a bit differently just seeing your thoughts before I purchase.

Like doing mods so trying to figure out on how I'm gonna get it all in there is a challenge I'm up to.

Do you think x2 5 watt heat pads would be enough to make 30 degree for printing temps.

翻譯年糕

Neil Ramsay
2019-07-04 09:31:46

Peter Lynn
2019-07-04 09:38:05

Stephen Farrell
2019-07-04 10:33:26

Peter Lynn
2019-07-04 11:05:58

原文網址 Peter Lynn
2019-07-02 08:56:19

Hi guys where can I purchase a heater setup for the photon to monitor and heat up temps accordingly. Cheers thanks.

翻譯年糕

Chris Wilander
2019-07-02 09:04:58

原文網址 Peter Lynn
2019-06-29 18:37:33

Is it normal to run high exposure times with different grade resins. 19 sec sound normal. Still tweaking but getting better results running higher times. Its winter here around 10 to 11 degrees.

翻譯年糕

Stephen Farrell
2019-06-30 07:38:36

原文網址 Peter Lynn
2019-06-23 15:56:04

Has anyone used dragon resin.

翻譯年糕

Niall Forrester
2019-06-23 16:31:26

Andrew Burton
2019-06-23 16:39:31

Peter Lynn
2019-06-23 16:40:19

Peter Lynn
2019-06-23 16:41:21

Andrew Burton
2019-06-23 16:43:57

Andrew Burton
2019-06-23 16:44:24

Andrew Burton
2019-06-23 16:44:28

Andrew Burton
2019-06-23 16:44:38

Peter Lynn
2019-06-23 17:11:51

Fadi Ashush
2019-06-23 19:57:42

Andrew Burton
2019-06-23 20:06:39

Fadi Ashush
2019-06-23 20:12:34

Andrew Burton
2019-06-23 20:13:24

Micah Vestal
2019-06-23 20:40:03

Fadi Ashush
2019-06-23 20:50:54

Fadi Ashush
2019-06-23 20:51:37

Wayne Rogers
2019-06-24 04:18:51

原文網址 Peter Lynn
2019-06-23 14:21:21

Printed with warm resin and warm photon on the inside to start with.

I honstley think this resin is hard to work with no matter what temp.

Here are some of my results

The surrport side still struggles.

翻譯年糕

原文網址 Peter Lynn
2019-06-23 08:35:33

Hello is there any resin tests and surrports settings for the anycubic photon I can download of thingiverse. I have done this one but looking at others i can do.

Is there a way to monitor print temps as it -1 in NSW goulburn.

Not gonna let monocure3d grey get to me I'm gonna nail this before I go back to work tomorrow ?

翻譯年糕

Vinicius Silva
2019-06-23 08:38:47

Robert Fliege
2019-06-23 08:43:34

Robert Fliege
2019-06-23 08:46:45

Georgina Cleaver
2019-06-23 09:53:23

Peter Lynn
2019-06-23 10:33:26

原文網址 Peter Lynn
2019-06-23 06:15:37

Update. A little better. The surrports kill it.

Running out of ideas.

To show difference

Anycubic green printed chairs space marine

Monocure3d grey cannon.

翻譯年糕

Stephen Farrell
2019-06-23 06:43:47

Jason Howe
2019-06-23 06:51:09

Peter Lynn
2019-06-23 07:19:43

Peter Lynn
2019-06-23 07:20:26

Jason Howe
2019-06-23 08:00:17

原文網址 Peter Lynn
2019-06-22 11:21:47

Can get this in the AU.

Has anyone used it. Reviews please

翻譯年糕

Ethan Brown
2019-06-22 11:25:16

Eric Jorgensen
2019-06-22 11:26:53

Peter Lynn
2019-06-22 11:34:21

Ethan Brown
2019-06-22 11:49:49

Ethan Brown
2019-06-22 11:50:50

Ethan Brown
2019-06-22 11:51:11

Ethan Brown
2019-06-22 11:51:43

Peter Lynn
2019-06-22 12:27:36

Ethan Brown
2019-06-22 12:33:11

Ethan Brown
2019-06-22 12:33:48

Peter Lynn
2019-06-22 12:51:08

Ethan Brown
2019-06-22 12:52:16

James Cachia-Garrett
2019-06-22 14:19:02

Azam Idris
2019-06-24 17:34:56

原文網址 Peter Lynn
2019-06-22 06:07:01

This is my problem. Prints nice but it does not matter what angle I print on or the cleanest ipa I use or the clean up I do I always end up with the surrport side looking horrible.

Monocure3d rapid resin grey.

Never had this problem with anycubic stock green.

Do you you guys thinks surrport settings could contribute to this.

翻譯年糕