Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Jim Brown
2019-05-28 10:56:13

Primed resin vs unprimed FDP (last one I promise :)

翻譯年糕

Sebastian Hennekes
2019-05-29 19:45:23

Jim Brown
2019-05-29 23:47:32

Keith Barnett
2019-05-29 23:51:59

Keith Barnett
2019-05-29 23:53:12

Jim Brown
2019-05-30 01:37:01

Greg Kourakos
2019-06-02 00:51:25

Jim Brown
2019-06-02 01:28:54

原文網址 Jim Brown
2019-05-28 09:26:32

Hmm. Last print came out really nice - but it looks like my tray now isn’t square to the resin bath. Any ideas?

翻譯年糕

Richard Shapiro
2019-05-28 09:30:14

William David Cunningham
2019-05-28 09:31:36

Jim Brown
2019-05-28 09:33:17

Jim Brown
2019-05-28 09:41:12

Simon Stewart
2019-05-28 10:04:05

Ryan Turner
2019-05-28 10:38:02

Guido A. Mandorf
2019-05-28 14:25:21

Joe Broggio
2019-05-28 15:14:21

Spike Walker
2019-05-28 15:18:49

Alex Vee
2019-05-28 15:34:12

Robert Becke
2019-05-28 16:30:27

原文網址 Jim Brown
2019-05-28 08:44:56

Following up on my support question from yesterday and thought I’d post the print results. I’m still floored by the quality of this 365 (on sale) dollar 3D printer.

翻譯年糕

Dimitri Riddle
2019-05-28 14:56:40

原文網址 Jim Brown
2019-05-28 02:27:43

Trying to download the Photon Validator software but it doesn’t come with a standard install file? I’m obviously missing something?

翻譯年糕

Andrey Sabrev
2019-05-28 02:39:45

Andrey Sabrev
2019-05-28 02:40:35

Jim Brown
2019-05-28 03:15:45

原文網址 Jim Brown
2019-05-27 11:28:15

Looking at a tougher print here. Input welcome on the supports.

翻譯年糕

Stephen Farrell
2019-05-27 11:35:02

Jim Brown
2019-05-27 11:39:03

Jim Brown
2019-05-27 11:45:18

原文網址 Jim Brown
2019-05-26 14:37:38

So my first photon print went out as a dud. ? The file I used was the one below, but I did not use any supports at all and I used the green any cubic resin that comes with the printer.

On my prusa she prints fine without any supports whatsoever and printed straight up with no lean. All that was in the photon at the end of the print was her base which had popped off the build tray - and nothing else. It looks like it made it through a few layers then came off the build plate. To calibrate the 0 layer I used the technique where the resin vat was in the photon (not the paper layer Height method) and you adjust it snug and then back it off 0.3mm to set up the print bed. Exposure time 8 seconds at 0.05 layer height. Thoughts/Help welcome!

翻譯年糕

Scott Thurston
2019-05-26 14:53:05

Scott Thurston
2019-05-26 14:53:41

Scott Thurston
2019-05-26 14:54:20

Bob Deblier
2019-05-26 15:02:44

Jim Brown
2019-05-26 15:04:56

Jim Brown
2019-05-26 15:06:22

Scott Thurston
2019-05-26 15:09:23

Scott Thurston
2019-05-26 15:11:02

Jim Brown
2019-05-26 15:19:43

Scott Thurston
2019-05-26 15:21:31

Jim Brown
2019-05-26 15:21:32

Scott Thurston
2019-05-26 15:24:36

Jim Brown
2019-05-26 15:25:09

Tamás Lehoczky
2019-05-26 16:54:40

Joel Reid
2019-05-26 18:08:41

Joel Reid
2019-05-26 18:12:45

Susan Sioux Mercer
2019-05-26 20:31:37

Nick Porterfield
2019-05-26 22:00:02

Jim Brown
2019-05-26 23:41:32

Jim Brown
2019-05-27 00:04:23

Jim Brown
2019-05-27 08:49:24

Jim Brown
2019-05-27 08:55:45

Jim Brown
2019-05-27 08:55:52

Susan Sioux Mercer
2019-05-27 09:27:57

原文網址 Jim Brown
2019-05-26 07:00:41

I’m still setting up and studying up before my first print with the photon and I have a couple function/safety questions.

1) Do you need to clean out the resin container that the build plate dips into (squeege and alcohol) after every print? I’m mainly going to print minis.

2) How often do you change the container of alcohol bath out and what do you do with the toxic cocktail of resin and alcohol?

Thank you in advance!

翻譯年糕

Trevor Tennison
2019-05-26 07:09:58