• COSPLAY 3D 建模
  • 3D列印服務
  • #maker+t=market
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Daniel McCarthy
2019-08-17 17:43:12

Trying to print some hex tiles. Testing flat to the plate without supports for speed atm. Getting this issue, any ideas? I’ve levelled everything correctly so that shouldn’t be an issue :s 10 sec exposure, 50 - 80 bottom. 8 bottom layers.

翻譯年糕

Steve Eldridge
2019-08-17 17:44:02

Daniel McCarthy
2019-08-17 17:46:40

David Damian
2019-08-17 17:49:37

Craig Bisgeier
2019-08-17 19:29:18

Mark Wardle
2019-08-17 19:33:56

Daniel McCarthy
2019-08-17 19:51:40

Russ Greene
2019-08-17 19:51:49

Daniel McCarthy
2019-08-17 21:33:10

Amanda Vyvey
2019-08-18 00:11:26

Alex Vee
2019-08-18 02:06:57

Nick Williams
2019-08-18 02:11:09

Mike Ratcliffe
2019-08-18 03:01:57

Mike Ratcliffe
2019-08-18 03:07:23

Daniel McCarthy
2019-08-18 04:02:20


原文網址 Daniel McCarthy
2019-08-16 06:34:20

Hey guys, I’m having a few problems with my prints. I wanted to ask: what are the most common causes of a print not sticking to the plate?

Im using a Photon S with the demo green resin shipped with the printer.
My prints appear stuck to the fep sheet rather than the plate.

So far to try and remedy this I’ve:

Levelled the build plate. Standard paper method. Can’t push the paper toward the printer but can pull it away with evenly distributed resistance. Screw tightened and Z=0.
Tightened the screws slightly to increase surface tension on the FEP sheet.
Increased bottom layer exposure to 80secs. Seems high for the default clear green resin but thought it worth trying.

Help would be greatly appreciated, Its starting to drive me nuts... I’m using Chitubox to slice with the supplied memory stick. I tested with another usb stick with no luck either.

翻譯年糕

Handrez Pintubola
2019-08-16 21:21:12

Daniel McCarthy
2019-08-17 05:16:06

Handrez Pintubola
2019-08-17 06:14:07


原文網址 Daniel McCarthy
2019-08-14 15:57:26

Does anyone know a fix for this? Printer just restarts shortly after pressing print. ?

Someone mentioned unplugging for a while but it doesn’t change. Much sadness. :(

Photon S.

翻譯年糕

Daniel McCarthy
2019-08-14 16:06:37

Nicolas Tsagarides
2019-08-14 16:33:52

Ben Hodgkinson
2019-08-14 16:35:03

Daniel McCarthy
2019-08-14 16:38:32

George Kinney
2019-08-14 22:53:29

Eric Green
2019-08-14 23:21:04

Keith Smith
2019-08-15 19:20:06

Daniel McCarthy
2019-08-15 19:22:52

Daniel McCarthy
2019-08-15 19:26:46

Daniel McCarthy
2019-08-15 19:30:28

Eric Green
2019-08-15 21:13:02

Keith Smith
2019-08-15 22:42:06

Daniel McCarthy
2019-08-15 22:57:33

Ted Sikora
2019-08-16 11:13:35

Aaron Wiggins
2019-08-16 13:06:00

Ted Sikora
2019-08-17 03:52:02

Aaron Wiggins
2019-08-17 04:43:09

Ted Sikora
2019-08-17 12:04:49

Aaron Wiggins
2019-08-17 12:06:23

Ted Sikora
2019-08-17 12:08:17

Ted Sikora
2019-08-17 13:17:58

Vinicius Silva
2019-08-18 05:21:44

Ted Sikora
2019-08-18 12:31:19

John Leonard
2019-08-19 17:15:27

Greg Deboer
2019-08-21 03:12:21

Minghua Kao
2019-08-21 03:16:53


原文網址 Daniel McCarthy
2019-07-09 20:46:20

Help please! First print of the test model was great but since I’ve had no luck with the resin completely failing to adhere to the plate (instead stuck to fep.) I’ve since re levelled the plate and done resaved several iterations of the model. About 4 fails so far. Any ideas why this could be happening? I’m a bit bewildered considering the test cane out perfectly and I’m using the same settings and resin type ?

翻譯年糕

Bob Deblier
2019-07-09 20:48:24

Kevin Lems
2019-07-09 20:50:16

Daniel McCarthy
2019-07-09 21:47:26

Daniel McCarthy
2019-07-09 21:48:57


原文網址 Daniel McCarthy
2019-07-08 06:41:55

Hello, total newbie question here but a few people recommended me ChiTuBox, which I have since downloaded and set to the Photon S profile. My question is if there are any 'EnableAA' settings in ChiTuBox much like the one visible in Photon WorkShop under 'slice settings?' I was looking forward to testing this feature.

Alternatively, I'm still looking for starter advice so if you'd like to recommend different slicing software, I'm all ears =)

翻譯年糕

Bob Deblier
2019-07-08 13:20:35

John Lowry
2019-07-10 11:23:46


原文網址 Daniel McCarthy
2019-07-06 05:12:55

Hi all! I’ve just received my photon s and have set it to work printing the test model supplied with the usb stick. I’m a 3D artist and this is my first printer so I’m really excited to finally be able to see and hold my creations ? . While I wait for this test to print I just wanted to ask for general newbie advise. Things I might want to do/ avoid doing, personal advise, useful links, settings, recommend resins, software to dl.etc? Is the software provided generally the best to use or is there better?

The test seems to be going well so far so I’m pretty stoked!

Sorry if this is covered in other conversations.etc. The wealth of information here is a little overwhelming to navigate. I’d appreciate any advise even if it’s just a point in the right direction ?

翻譯年糕

Mika Vienonen
2019-07-06 05:58:09

Susan Sioux Mercer
2019-07-06 06:54:46

Daniel McCarthy
2019-07-06 07:14:37

Daniel McCarthy
2019-07-06 15:47:53

Susan Sioux Mercer
2019-07-06 15:55:58


 

討論主題

全不選 常用關鍵字