Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ron Chau
2019-08-06 12:45:00

The left print with the higher details printed with maybe 75% of the prints coming out okay. I changed the exposure times and got a much higher success rate, but at the cost of details (check the heads). How much should I dial exposure back?

Settings for left and right prints:
Photon S, Elegoo Grey resin
Layer Height: 0.05 mm -> 0.05mm
Bottom Layer Count: 3 -> 8
Exposure Time: 8 -> 18
Bottom Exposure Time: 40 -> 100
Light-off Delay 0 -> 0
Bottom Light-off Delay: 0 -> 0

翻譯年糕

Robert James
2019-08-06 12:53:59

Ron Chau
2019-08-06 12:55:59

Craig Burrows
2019-08-06 13:14:58

Craig Burrows
2019-08-06 13:15:43

Ron Chau
2019-08-06 13:22:05

Bob Deblier
2019-08-06 14:35:09

Robert James
2019-08-06 14:52:59

Victoria L. Cordone
2019-08-07 11:15:53

Victoria L. Cordone
2019-08-07 12:02:26

原文網址 Ron Chau
2019-08-03 01:31:52

Hi, all. Any idea what's happening on my Photon S? I did two attempts on the halfling and it's not printing most of the model. Is this a support issue or one of positioning? Elegoo grey on the same settings for both prints.

The rest of the models has small issues like incomplete weapons and accessories.

翻譯年糕

Paul West
2019-08-03 01:41:39

Joshua Collins
2019-08-03 01:45:58

Ric Watts
2019-08-03 03:48:05

Joshua Collins
2019-08-03 04:51:31

Ron Chau
2019-08-05 01:30:38

原文網址 Ron Chau
2019-07-30 12:58:29

Third printing attempt on the Photon S and it's better, but there's still some issues. I re-leveled the build plate in between each print and switched over to Chitubox for the third one. Afterwards, I noticed some circular indents on the FEP film - could this be the cause?

Settings for the third print, using AnyCubic Green:

Layer Height: 0.05 mm

Bottom Layer Count: 3

Exposure Time: 8 s

Bottom Exposure Time: 40 s

Light-Off Delay: 0 s

Bottom Light-Off Delay: 0 s

翻譯年糕

Conor Tanji
2019-07-30 15:19:03

William Riker
2019-07-30 17:00:47

Jon Carroll
2019-07-30 21:05:48

原文網址 Ron Chau
2019-07-29 03:54:54

Hi, everyone. I picked up an AnyCubic Photon S this week and I'm running into some failures during my initial prints. Both attempts used the green resin that the printer came with.

The first attempt used settings reported by Daniel Perez on the community exposure settings Google Sheets. ~11 hours.

Layer: 0.02
Normal Exposure Time: 7.5
Off Time: 1.5
Bottom Exposure: 40
Bottom Layers: 8

The second attempt used the default settings. These prints came out slightly better. ~5 hours.
Layer: 0.05
Normal Exposure Time: 8
Off Time: 1
Bottom Exposure: 60
Bottom Layers: 3

Both attempts ended with a small layer of hardened resin on the FEP film. I cleaned everything and re-leveled the build plate in between the two attempts.

Photos shown are from the second attempt. Any advice?

翻譯年糕