• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Kelly Filgo
2019-10-05 11:10:50

I've documented some post-print/pre-cure deformation that I thought might be interesting. This print sat on the supports for about 30 hours before being cut loose and then sun cured. I'm pretty confident that it was nice and round when the print was over. Now it is an oval with a 2mm sag (z) and a 2mm widening (x). Note the columns from the center are stretched in the x and fatter in the z directions by a mm or so.

Apart from that, I'm amazed by how much of the thin lattice I was able to preserve during trimming and how resilient it is. Before curing it had an amazing ability to spring back to original shape and after curing it still retains some of that quality.

Enjoy the dimensional nerd musing.

翻譯年糕

Kelly Filgo
2019-10-05 11:11:44

Kelly Filgo
2019-10-05 11:13:23

Kelly Filgo
2019-10-05 11:14:13

Kelly Filgo
2019-10-05 11:15:49

Nathaniel Red Weidner
2019-10-05 11:20:17

Kelly Filgo
2019-10-05 11:21:55

Pietro Malaguti Abbate
2019-10-05 20:45:53

Kelly Filgo
2019-10-05 21:02:56

Pietro Malaguti Abbate
2019-10-05 22:17:17


原文網址 Kelly Filgo
2019-10-03 19:36:55

I think I'll need to partially cure this before removing supports from the more delicate parts.

翻譯年糕

Brian Romine
2019-10-03 19:39:44

Jay Jones
2019-10-03 19:42:43

Petr Pechar
2019-10-03 19:53:43

Petr Pechar
2019-10-03 19:54:27

David Seaman
2019-10-03 19:58:43

Jay Jones
2019-10-03 20:02:42

Lars Wenner
2019-10-03 20:26:09

Omar Baez
2019-10-03 20:30:58

Paul West
2019-10-03 20:31:14

Jeffery Nelson
2019-10-03 20:39:20

Arnaud Rousseau
2019-10-03 20:40:29

Lora Delvecchio
2019-10-03 20:57:14

David Boccabella
2019-10-03 22:03:22

Nathaniel Red Weidner
2019-10-03 22:03:44

Greg Mortensen
2019-10-03 22:16:38

Sherri Johnson
2019-10-03 22:28:11

Ludo Eksel
2019-10-03 22:34:11

Pietro Malaguti Abbate
2019-10-03 22:57:45

Sherri Johnson
2019-10-03 22:59:03

Pietro Malaguti Abbate
2019-10-03 23:02:53

Kelly Filgo
2019-10-03 23:13:48

Kelly Filgo
2019-10-03 23:17:34

Kelly Filgo
2019-10-03 23:19:20

Nathaniel Red Weidner
2019-10-03 23:26:35

Mark Wardle
2019-10-03 23:44:04

Sherri Johnson
2019-10-03 23:53:28

Kelly Filgo
2019-10-04 00:16:28

Robert Small
2019-10-04 00:18:16

Robert Small
2019-10-04 00:19:26

Kelly Filgo
2019-10-04 00:27:09

Kelly Filgo
2019-10-04 00:30:25

Kelly Filgo
2019-10-04 00:30:34

Kelly Filgo
2019-10-04 00:31:36

Zeno Silva
2019-10-04 00:44:21

Robert Small
2019-10-04 01:35:11

Fábio Nogueira
2019-10-04 02:32:26

Fábio Nogueira
2019-10-04 02:34:12

Alexx Butnotalex
2019-10-04 02:40:55

Robert Small
2019-10-04 02:41:44

Matt Remus
2019-10-04 02:46:08

Nathaniel Red Weidner
2019-10-04 02:47:10

Matt Remus
2019-10-04 03:01:10

Petr Pechar
2019-10-04 03:05:55

Petr Pechar
2019-10-04 03:07:06

Zeno Silva
2019-10-04 03:35:33

Michal Šmerik
2019-10-04 04:41:30

Juan Pablo Bagnon
2019-10-04 04:43:21

Rick Hanson
2019-10-04 05:00:10

Gabe Snooks
2019-10-08 21:57:58

Michal Šmerik
2019-10-09 01:08:59

Joel Reid
2019-10-09 17:12:52

Kelly Filgo
2019-10-09 21:47:22


原文網址 Kelly Filgo
2019-09-28 03:06:41

I checked the photonsters.org FAQ and didn't see an answer to this question: Can I cover the box during a print with the foam shipping sleeve that it shipped in? I'm worried about dust and daylight getting in. Does the yellow glass really work? I'm in a room with lots of windows and daylight. Would the foam sleeve make the box too hot?

翻譯年糕

Danny Broekhuis
2019-09-28 03:14:55

Rus Justrus
2019-09-28 03:20:21

Kelly Filgo
2019-09-28 03:43:01

Matt Hooton
2019-09-28 17:23:15

Jerry Mojares
2019-09-30 02:59:19


原文網址 Kelly Filgo
2019-09-27 11:30:47

I am getting my new Photon ready for a test print. Updated firmware to 4.2.18 then leveled via Flint Read method (check for dust first!!). All super easy thanks to this great group and the folks at Photonsters.org.

So excited to get started.

翻譯年糕


 

討論主題

全不選 常用關鍵字