Anycubic Photon Printer Owners 造訪社團

原文網址 Matt Olsen
2019-11-28 05:01:34

Ok. I printed this building, and the front side failed to stick to the plate. So I rotated it 180° and tried again. The portion that failed before worked, but then the opposite side failed. Her are my supports and settings.

Is it a leveling issue, is the fep too loose/tight. Elegoo grey.

好吧. 我列印了這棟建築, 而前方沒能堅持到盤子上. 所以我旋轉了180°並再試一次. 之前失敗了, 但後來對方失敗了. 她是我的支援和設定.

這是一個平穩的問題, fep太鬆松/緊了. Elegoo grey.

· 查看原文 · 為此翻譯評分

Felipe Carascosa Ferro
2019-11-28 05:09:40

Kevin Boogaard
2019-11-28 05:21:28

Matt Olsen
2019-11-28 06:38:54

Kevin Boogaard
2019-11-28 06:40:44

Matt Olsen
2019-11-28 06:42:26

Kevin Boogaard
2019-11-28 06:45:53

Matt Olsen
2019-11-28 08:45:28

Bob Deblier
2019-11-28 22:16:23

Darren Donovan
2019-11-28 22:37:02

原文網址 Clarence Prigent
2019-11-28 04:54:32

Thanks for the add

感謝您的新增

· 查看原文 · 為此翻譯評分

原文網址 Stephen Ross
2019-11-28 04:35:22

A little print 1/1700 mobius from gundam seed. Try not sneeze.

翻譯年糕

Kasper Kolsrud
2019-11-28 04:38:02

Stephen Ross
2019-11-28 04:40:00

Justin Chow
2019-11-28 04:43:04

Abu Hayder Al-Tai'ee
2019-11-28 04:50:23

Stephen Ross
2019-11-28 05:10:49

Stephen Ross
2019-11-28 05:12:24

Justin Chow
2019-11-28 06:01:47

Stephen Ross
2019-11-28 06:35:52

原文網址 Mikkel Jensen
2019-11-28 04:30:51

Soooo, Does anyone know what temperature the cured resin can withstand? using the Green resin standard.

翻譯年糕

John Chrapkowski
2019-11-28 04:31:47

John Chrapkowski
2019-11-28 04:32:25

Mikkel Jensen
2019-11-28 04:33:05

原文網址 James Vincent Paquette
2019-11-28 03:38:48

Can anyone recommend a good diy heater setup?

翻譯年糕

原文網址 Raphael Truffi Bortholuzzi
2019-11-28 03:30:21

Test paint on this baby calf I printed using green translucid and ANYCUBIC . Painted with acrylics, oils, enamels, dry pastel and pigments.

翻譯年糕

Denis Maddalena
2019-11-28 03:41:52

Raphael Truffi Bortholuzzi
2019-11-28 03:42:26

Stephan Mccoll
2019-11-28 03:47:27

Scott Pavlich
2019-11-28 03:49:11

Ricardo Pedro
2019-11-28 03:55:54

Chris Koonce
2019-11-28 03:55:57

Steven Huynh
2019-11-28 04:00:29

Raphael Truffi Bortholuzzi
2019-11-28 04:04:52

Raphael Truffi Bortholuzzi
2019-11-28 04:05:20

Iain Morrison
2019-11-28 04:05:23

Raphael Truffi Bortholuzzi
2019-11-28 04:05:55

Raphael Truffi Bortholuzzi
2019-11-28 04:06:05

Raphael Truffi Bortholuzzi
2019-11-28 04:06:52

Raphael Truffi Bortholuzzi
2019-11-28 04:08:22

Steven Huynh
2019-11-28 04:33:34

Iain Morrison
2019-11-28 04:38:06

Deniz Yüksel
2019-11-28 05:00:08

Raphael Truffi Bortholuzzi
2019-11-28 05:08:16

Arthur Erbricht
2019-11-28 05:31:45

George Bulte
2019-11-28 06:13:54

原文網址 Mithilesh Kotangale
2019-11-28 03:28:09

Hello need a help from the faternity people due to some reason fep film got torn & my machine filled with resin. I got it cleaned but my photon sensor is not working & it's difficult to reset it to z=0 please let me know from where I should get a new sensor or how to repair it
I am from India Mumbai.
Thanks

翻譯年糕

原文網址 Manuel Boria
2019-11-28 03:21:29

Hey folks! The second Owlbear Cub of the batch is done :) Available now on my Patreon and Gumroad.
Let me know what you think ^^ https://www.patreon.com/Manuel_Boria
https://gumroad.com/manuel_boria 翻譯年糕

原文網址 Jeremy Babcock
2019-11-28 03:17:15

Hey everyone, just started and did my first print and seems to look ok to me ?‍♂️ My questions is there seems to be some residue or sediment left in the tank? Is this normal and should I strain it before doing another print? Also what is it, slightly cured resin maybe? Thanks greatly in advance!

I’ve only printed the test file off the USB once. I used Esun Plant based resin (Green) and thought it would be a close enough match to the pre-sliced settings to get me started.

翻譯年糕