Anycubic Photon Printer Owners 造訪社團

原文網址 Connie Marie Ardwin
2020-03-15 06:33:42

Just wanted to say thanks to this entire community. Hubby and I are newbie 3D printers. I’ve been FDM printing for less than a year and we decided to upgrade from the mono price mini to resin printing with the photon zero. We have not had much success with prints, but the help here has made troubleshooting each variable in the print process tolerable! So, thanks :)

翻譯年糕

Steven Molen
2020-03-15 06:38:03

Steven Molen
2020-03-15 06:39:56

原文網址 Patrick Nixon
2020-03-15 06:04:49

I have my Photon in an enclosure and cannot flip the lid over the center of gravity while working in the machine. This is a Kickstand of sorts to keep it up and out of my way. Slots onto the Lower Left corner of the lid and sits on the top left of the frame in the lid opening. There are spots for a 3x10mm magnet (home depot/lowes?) to assist with keeping the lower part of the kickstand in place. During my testing, they weren't needed though.

https://www.thingiverse.com/thing:4222364 翻譯年糕

Justin Lincoln
2020-03-15 07:26:56

Patrick Nixon
2020-03-15 07:28:58

Heiko Zschimmer
2020-03-15 15:45:10

Heiko Zschimmer
2020-03-15 15:49:20

Patrick Nixon
2020-03-15 18:16:17

Heiko Zschimmer
2020-03-15 19:19:25

原文網址 Tucker Adams
2020-03-15 05:52:12

so I tried adding auto supports following 3d printed table top's video on youtube using PrusaSlicer auto supports, then exporting as STL with supports, opening in chitubox and slicing, and printing. Unfortunately the model detached from the supports and failed. Given this is such a popular method, is there anything I probably missed as a beginner with resin printing? The key caps I printed from the Photon Slicer with auto supports from it printed just fine

翻譯年糕

原文網址 Kory Kendziora
2020-03-15 05:19:01

Time for a new LCD already? I literally have only printed about 10 things. I did have some leaks before aid applied the kapton tape ??‍♂️ . Best place to pick up one?

翻譯年糕

Kory Kendziora
2020-03-15 05:21:52

Paul Oliveira
2020-03-15 05:22:59

Jeremy Mongoose Harris
2020-03-15 05:54:38

Kory Kendziora
2020-03-15 06:04:02

Jeremy Mongoose Harris
2020-03-15 06:05:10

Kory Kendziora
2020-03-15 06:09:00

Jeremy Mongoose Harris
2020-03-15 06:09:49

Justin Lincoln
2020-03-15 08:31:22

Justin Lincoln
2020-03-15 08:31:34

原文網址 Vishnu Gollakota
2020-03-15 05:00:28

Does anyone have any recommendations for priming? Iv never primped one of my prints so I wanted to know if there was any good tips for it

翻譯年糕

Chad Elstad
2020-03-15 09:00:20

原文網址 Ronni Kristiansen
2020-03-15 04:54:08

Is it to be expected that my prints become more brittle after a FEP change? The old FEP was a little cloudy at the end, so thinking more light gets through now, hence more exposure.

翻譯年糕

Stefan Giudici
2020-03-15 04:57:15

Nope

Chris Holden
2020-03-16 16:32:40

Did your Photon come with a tank with FEP already installed by the AnyCubic factory? Did you replace it with the same FEP sheets from AnyCubic, or did you buy a cheaper alternative online, to save a few quid?

Ronni Kristiansen
2020-03-16 23:37:41

It came with a FEP that has worked well for 3 months, but needed a change. I used original AC FEP for the change and managed to tune it to around 350-370hz. If I tune it any lower, the screws will be too raised. The first few bottom layers now make a sucking noice when releasing from the FEP, but the prints are perfect.... just more brittle than before.

原文網址 Derek Mears
2020-03-15 04:43:42

Flash sale

翻譯年糕

Tucker Harris
2020-03-15 07:35:09

Jeremy R Kufer
2020-03-15 13:12:12

原文網址 Daniel Thredson Art
2020-03-15 04:36:46

Little big planet teenage mutant ninja turtles
Work that we do for 3D print
Print by Geoffroy

小大星球青少年忍者烏龜
我們為3 d列印所做的工作
由geoffroy列印

· 查看原文 · 為此翻譯評分

Daniel Thredson Art
2020-03-15 04:37:04

Daniel Thredson Art
2020-03-15 05:35:35

Daniel Thredson Art
2020-03-15 05:35:56

Damo Cramp
2020-03-15 06:35:05

Daniel Thredson Art
2020-03-15 06:51:51

Josh Thomas
2020-03-15 09:13:01

Josh N Bee
2020-03-15 09:18:20

Daniel Thredson Art
2020-03-15 09:19:08

Daniel Thredson Art
2020-03-15 09:19:26

Daniel Thredson Art
2020-03-15 09:20:03

Daniel Thredson Art
2020-03-15 09:20:10

Joe Tacconelli
2020-03-15 11:30:37

Daniel Thredson Art
2020-03-15 11:32:52

Robert Lopez
2020-03-15 17:30:00

Daniel Thredson Art
2020-03-15 17:53:32

原文網址 Adam Osga
2020-03-15 03:47:58

Hello everyone, I'm new to the page and a total noob to 3D printing. I finally got the sample print to print correctly with my photon. One thing I've noticed with my current settings though is that the base layer is probably a bit too attached to the base plate. What is best to reduce this a bit? Less layers, less base cure time, or some other factor? Thanks!

翻譯年糕

Brendan Wood
2020-03-15 04:03:23

Jamal Virani
2020-03-15 10:31:04

原文網址 Mike Mccune
2020-03-15 03:28:30

Changed resin and first time running the xps test. 20 micron layer height. Any help reading this. I'm thinking between column 7 and 8 so like 15 sec layer time.

翻譯年糕