Anycubic Photon Printer Owners 造訪社團

原文網址 Hantar Kurniawan Gultom
2020-01-21 12:09:15

hi folks,

have you guys in this group try water washable resin?

what do you think for this resin?

翻譯年糕

Stefan Giudici
2020-01-21 12:17:54

Richard Humble
2020-01-21 14:42:39

Joseph Daniels
2020-01-22 03:15:17

原文網址 Ben Garbutt
2020-01-21 11:40:30

First print on my photon s, tried to print the test town.
Settings were
Bottom layer count 8
Bottom exposure 70
Exposure 8
Light off 1
Layer height 0.05
Anycubic green

Using the fep that came pre installed in the vat
Used flint method of leveling.

Any help?

翻譯年糕

Ben Garbutt
2020-01-21 11:41:27

Jim Linder
2020-01-21 12:07:29

Christopher Carstens
2020-01-21 12:20:42

Pierre Eichel
2020-01-21 17:55:56

Ben Garbutt
2020-01-21 17:56:19

Pierre Eichel
2020-01-21 17:57:46

原文網址 Thomas Grimm III
2020-01-21 11:38:24

Anyone know that burnout temp of the ANYCUBIC 3D Printer Resin?
I’m a jewelry apprentice at Jared’s the diamond galleria and I thought about printing a ring and trying to cast it.

翻譯年糕

Blake Roney
2020-01-21 11:40:35

Jeremiah Chetwood
2020-01-21 11:42:23

Jeremiah Chetwood
2020-01-21 11:42:53

Benjamin Cole
2020-01-21 13:17:43

Jeremiah Chetwood
2020-01-21 20:40:36

原文網址 Jason Archuleta
2020-01-21 11:34:45

I printed a Baby Yoda for my daughter and for the life of me I can not get the green right. If any of you Baby Yoda painters use Army Painter how did you get the right color green?

翻譯年糕

John McLean
2020-01-21 11:35:15

Jason Archuleta
2020-01-21 11:35:33

John McLean
2020-01-21 11:37:07

John McLean
2020-01-21 11:37:41

Jason Archuleta
2020-01-21 11:38:01

Evan Rosario
2020-01-21 12:45:50

Ben Brooks
2020-01-21 13:11:23

Matman Brauchli
2020-01-21 16:11:00

Matman Brauchli
2020-01-21 16:12:11

Johnny Grant
2020-01-21 23:05:25

Jason Archuleta
2020-01-24 23:00:40

原文網址 Jairo Ledesma
2020-01-21 11:06:37

I found this while looking for resin recomendations
Can anyone confirm or deny this?

翻譯年糕

Emily Whitehouse
2020-01-21 11:10:03

Sam Spencer
2020-01-21 11:12:00

Jason Patterson
2020-01-21 11:14:36

Jairo Ledesma
2020-01-21 11:14:51

Sam Spencer
2020-01-21 11:16:10

Daniel Hendlowitch
2020-01-21 11:17:08

Alexander Bayerdorffer
2020-01-21 11:17:37

Andrew M Dunlap Jr.
2020-01-21 11:26:24

Sam Spencer
2020-01-21 11:27:25

Andrew M Dunlap Jr.
2020-01-21 11:28:24

Sam Spencer
2020-01-21 11:31:09

Clark Paints
2020-01-21 11:46:01

Jim Linder
2020-01-21 12:05:46

Christopher Barnes
2020-01-21 12:07:28

Jairo Ledesma
2020-01-21 12:08:24

Ben Brooks
2020-01-21 12:42:00

Sam Spencer
2020-01-21 12:42:30

Ben Brooks
2020-01-21 12:43:05

Grant Kinnick Smith
2020-01-21 12:57:33

Mark Reynolds
2020-01-21 13:32:15

Jason Pedersen
2020-01-21 13:38:59

Sander van Deijl
2020-01-21 13:39:00

Ben Brooks
2020-01-21 13:51:02

Sander van Deijl
2020-01-21 13:51:37

Ben Brooks
2020-01-21 13:55:29

Sander van Deijl
2020-01-21 13:56:51

Ben Brooks
2020-01-21 14:00:00

Ben Brooks
2020-01-21 14:00:12

Andrew Goulart
2020-01-21 15:32:11

Ante Ravlić
2020-01-21 16:56:17

Robert Zittnan
2020-01-21 17:16:07

Krunoslav Zlomislic
2020-01-21 17:21:57

Marcin Czyszczon
2020-01-21 18:38:12

Fabien Somersbaep
2020-01-21 19:41:00

Gustavo Enriquez
2020-01-21 20:45:09

Chad N Rachel Dion
2020-01-21 21:56:06

Gabe Snooks
2020-01-21 22:07:00

Jake Gilmore
2020-01-21 22:45:32

Jairo Ledesma
2020-01-22 01:31:31

Jake Gilmore
2020-01-22 02:02:05

Mark Wardle
2020-01-22 02:02:24

Jairo Ledesma
2020-01-22 02:14:08

David Collinson
2020-01-22 02:15:55

David Collinson
2020-01-22 02:16:21

Jim Monaco
2020-01-22 02:39:30

Mark Wardle
2020-01-22 02:41:59

David Collinson
2020-01-22 02:50:30

Kevin Rank
2020-01-22 03:55:37

David Collinson
2020-01-22 04:04:16

Jairo Ledesma
2020-01-23 12:22:50

原文網址 Mike Tate
2020-01-21 10:56:54

Only thing that changed is i updated chitubox. Hm. Also ruined my fep. So gotta wait for new stuff. Got 40 minis printed in 4 days so not bad, I'd say.

翻譯年糕

Alex Vee
2020-01-21 11:01:47

Mike Tate
2020-01-21 11:04:54

Mike Tate
2020-01-21 11:06:50

Mike Tate
2020-01-21 11:07:00

原文網址 Kyle Hunt
2020-01-21 10:52:20

I printed out a mini and it looks like the base flared up a bit on one side causing it to not print as accurately. I also tried to print a wall section (dungeonsticks) on the same print and that didn't stick at all.

I'm thinking it'd a leveling issue but wanted to get opinions

翻譯年糕

Stefan Giudici
2020-01-21 11:01:37

Kyle Hunt
2020-01-21 11:48:10

原文網址 Ryan Shelvik
2020-01-21 10:36:49

Hey guys. I'm trying prep a model for printing, and the stl is pre-hollowed. I don't think it is big enough to make hollowing worth the work of supporting the inside islands. So, thought I would drop it in meshmixer and make solid. I set solid accuracy and mesh density to max (in an effort to keep the detail)...but it isn't solid. Any advice?

翻譯年糕

Matthew Overbeck
2020-01-21 10:49:38

Ryan Shelvik
2020-01-21 22:20:03

原文網址 Kelvin Pang
2020-01-21 10:14:28

Hi guys. Im still pondering on the best approach to split this up into separate parts for printing. There is just too many islands between the model and the base and it is going to be a nightmare removing supports from there. Any advice/suggestion is much appreciated. Thank you.

翻譯年糕