CR-7/8/10 3D Printer 研究社 造訪社團 » EX

這訊息的意思是程式碼的空間不夠了。
應該是原本控制板的空間較小，打開新功能後程式變大放不下。

哇哩咧

對阿...應該是資料區超過64k節區了..8 BIT CPU 的限制,有時間再來砍內容看看能不能擠出空間.

總共多了幾行呢？
看看裡面有沒有註解什麼的，
刪掉一些，
不然MEGA2560也很好用……

大概打開auto bad leveling 㑹增加lcd 上的一些圖形顯示所以data seg. over 64k了，找時間來砍內容，如果真不行就要換成mega2560了，奇怪小七這塊板子的source code compile 後bin檔比用mega2560大超多。

我沒在玩 arduino ，不過一般來說 compiler 有支援的話，還是可以用 bank switch 超過 64 KB 不是嗎?

First of all, take pictures of the problem. For example capture screen of your cura setting, the model you want to print, the fail cases.

I'm going to try lower bed temp, adjust the amount of feed for the Extruder.

雙十一是什麼? 可以吃嗎?

光棍節

I think you should ask the Creality 3D to send another pcb to you(because they supply one year warranty for microcontroller boards), or you can buy another one from them.

I tried locating them, but I couldn't find an email address or any other contact info for Creality. I'm going through GearBest, since it is where I purchased the printer from. GearBest says that they are not getting a response from Creality either. I a m so sad and embarrassed that I paid so much for something that doesn't work and all of my friends keep asking if I have printed anything yet. They would probably buy one themselves if I was successful, but they are surely hesitant to buy ANY 3D printer from anyone now. Do you have contact info for Creality?

That's impossible, because the service of Creality is very good. I think GearBest cheated you. Because I am also his one of distributors , I know they're very responsible for they're products. Do you have QQ or Wechat ? or I can help you get the email? BTW, where is your location?

I live in Milwaukee, Wisconsin, USA. I don't have either chat App , but I am downloading WeChat now.

I really like the product except for it not functioning.

Michael Haller Give me a little time, I will give you his Wechat ID. You can chat with him online.

Thank you for your help.

WeChat ID: Creality-3d

Well, I finally had time to try the suggestions given to me. I preheated the hot end and, yes, the Extruder works and also the laser. Why does the laser work only after I preheat the hot end and/or bed?

My filament does not lay on the bed. I assume the hot end is to far away from the bed, so I'll look into making sure it is closer. 0.1mm?

One paper thickness, making sure the paper between the hot end and the heat bed is easy to pull, but also not tightened or loosely

Ok and thank you so very much for helping previously. I was so distraught before and now I am humbled by my stupidity about the preheating.

Preheating is not necessary to make laser work. You can try to set fanspeed to 255, then the the laser will work.

Wow,thank you. I'll try it. I finally printed my first 3D print after adjusting the bed from the hot end to one piece of paper thickness. It is not perfect, but I will figure out what went wrong. Thanks again for all of your fine help and great advice.

How many steps per mm does the CR-8 take? If you have any more critical information for setting up CURA for use in making my own designs I'd appreciate it. Thanks.

My CR-8 Printer is not recognized by my computer when I have the USB plugged in. Do I have to do everything from the SD card?

Maybe your software setting in NB is different from CR-8 firmware. You should ask Creality 3D

hi bro, can you list your questions in one post by 1,2,3..? I can't figure out whats the main problem you are in.

I guess my main question is: what settings should be in CURA for the CR-8 3D printer?

把模型放大十倍的話也看不到嗎？

ㄟ ~~~又有了耶!!! 原來是字體大小問題，放大2-3倍就有了

看來立體字體不能太迷你XD

因為你字體太薄了 如果你壁厚調小可能可以用原本的大小印出來

這個方法我試過，行不通，我是用coredraw造字再拉厚度的
你用textexp 後可以用 pedit 或j 檢查看看，多餘的線很多
而且你得選用粗一點的字體

David Liao 要不要這兩隻狐狸擺一下..幫我拍張橫照 我擺在社團首頁照片，每次看到都覺得好美 XD

那等會我拿單眼出來拍好了

請教狐狸的線材是用哪家的，質感好優啊~

大大請問你噴頭溫度用幾度呢？建議溫度是180度，給你參考，請問你的噴頭有裝teflon嗎？

木料加熱會膨脹 擠出機要夾緊擠過去

原來團內也有賣料的支援，讚讚讚