切片及相關軟體設定

原文網址 吳晉隆
2016-11-08 00:06:25

馬拉松列印~

迷你版Arkham knight helmet

可惜只有小朋友才能戴

時間:117小時

重量:850g

層厚:0.2mm

填充:15%

切層:CURA

Man Cheng
2016-11-08 00:32:05

酷

葉志晃
2016-11-08 07:51:50

數據值得參考，謝謝

熱瓜米
2016-11-08 08:27:52

請問support的數據？很平滑，十分關注

James Lu
2016-11-08 08:46:50

酷斃了!

陳勁霖
2016-11-08 13:15:41

這台打印機是？？

原文網址 Michael Haller
2016-11-06 04:31:17

How ca CURA be set so all G-code files start by moving Z up, X and Y to the center of the bed, the Z down to start the print?

翻譯年糕

Ally Yao
2016-11-06 11:08:02

You can click on the right button of your mouse on the Gcode file,and then you will fine the center button^^

Michael Haller
2016-11-06 11:17:53

OK, thanks, I'll look at it. Maybe there will be comments to help locate it, but I can probably figure it out. I just thought there was some way to set up CURA to automatically do it for every print. I can paste the instruction onto every print I suppose. I just imagined it could be automatically done each time.

Ally Yao
2016-11-06 13:03:02

CURA dose not set up automatically, you will see the data of your last print . You can save the data to your computer or. you can enter the data when you print ^^

Michael Haller
2016-11-07 06:39:39

I cut and pasted the command lines that moved the X, Y and Z axis just like I wanted. Unfortunately, I am not satisfied with how CURA is writing the G-code (a lot of crazy and really bad positioning). I tried Slic3r and while it automatically positions the axis' how I wanted, the prints are not laying nor filling properly. I imagine I don't have it set up correctly. What do people use for the CR-8 using PLA and ABS? Thanks in advance.

原文網址 Michael Haller
2016-11-06 04:29:55

What parameters should CURA be set at for the CR-8?

翻譯年糕

原文網址 Michael Haller
2016-11-06 04:28:40

While my first print worked, I haven't been able to do one I downloaded. I used CURA to write the G-code from the 3D file I got off Thingverse. The test object file brought the Z-axis up and the X&Y axis' moved the head to the center of the bed before the Z-axis came down and the print started. The G-code from the file CURA generated started to print at the edge of the bed. I stopped the print in time, but I would prefer for any future prints to start the same way as the test object printed by going up, to the center, then down and start printing. Does anyone have suggestions how to, possibly configure CURA to start all prints in this way? Also does anyone know all of the parameters I need to set CURA at for the CR-8? Thanks in advance.

翻譯年糕

Alan Chen
2016-11-06 08:06:52

I think there are CURA instructions in your SD card, when you buy it. You should follow its instructions and try it again.

原文網址 謝嘉龍
2016-11-04 12:56:19

昨天印的耿鬼，使用的切片軟體是CR10附的創想三維，支撐實在令人失望，上次印卡比獸改用Cura2.3，也沒有比較好。

乾脆購買Simplify3D來印，無奈網路上找不到適合的參數設定可以參考，各位網友有人可以分享嗎？感謝各位先～

印表機：CR-10

張開
2016-11-04 12:59:33

為什麼要躺著印？

宋昇嶧
2016-11-04 13:26:53

站著印吧(卡比跟耿鬼)

張開
2016-11-04 13:33:04

我也覺得站著印效果比較好，尖端不適合在底面

沈揚
2016-11-04 13:35:42

Cura 的支撐我覺得很浪費支撐材
且拆下支撐材後可能不只是要打磨
而是要上補土才能修補...

Chen A-Chia
2016-11-04 13:37:37

這樣印就是s3d印出來效果也不好

チェン幸せな
2016-11-04 14:00:28

這隻要站著印的說,站著印支撐會再底部與尾巴和兩隻手,至少成品站立著可以無視底部爛表面,成品背部的尖刺因該是不用開支撐也OK....

チェン幸せな
2016-11-04 14:01:36

チェン幸せな
2016-11-04 14:03:33

原尺寸Cura支撐已送人,1.6倍換樹狀支撐開印中.....

宋昇嶧
2016-11-04 14:15:38

謝嘉龍
2016-11-04 18:29:42

感謝各位前輩的建議，等星期一再來站著印。（現在印其他的東西）
有人可以指導怎麼設定S3D適用於cr10嗎？我錢都花下去了(ｰｰ;)

Charlie Ting
2016-11-05 04:22:56

擺法錯誤

原文網址 Kevin Lan
2016-10-31 11:17:45

Simplify 3D更新了.(當然目前沒有愛心版本)

開始支援多國語文(包括日語), 也許可以看到官方支援中文的一天(?), 或是有人可以開始進行漢化了.

支援3個或以上的擠出機.

David Liao
2016-10-31 11:30:09

不知道他支撐的辨識能力加強了沒喔

黃俊誠
2016-10-31 12:38:42

不過軟體價格很貴

Boon Kheng Tang
2016-11-01 21:31:07

剛剛試了一下，手動支撐叫不出來

原文網址 蘇東平
2016-10-28 14:20:54

大家好～～我來求救了
我是大概一年前跟彭大的團的小8
之前使用都OK 之後陸續出現一些異樣
常見狀況的是加熱完畢就停了不動了
不然就是print 檔案之後出現下面奇怪的XXX->.gco 然後就完全不動了
（正常是heating printing)
我換過兩張SD卡使用軟體的Cura（更新到最新版舊版也一樣）
設定都有照著社團的設定！

但最詭異的是有時候他是可以正常運作的（同樣的SD卡同樣的檔案）我同一個檔案印了一次正常立刻再印一次就出現錯誤

有時候開機就出現"wait for user" 還不是印到一半停下來
至於印到一半停下來的事情也發生好幾次

正常運作的時候印列的品質非常好我很滿意但這些奇怪的問題讓我搞一天可能只印出一個作品

請大家教教我～～～感謝