CR-7/8/10 3D Printer 研究社 造訪社團 » 用戶發文

I need the E-Mail for Creality.

http://www.cxsw3d.com/lianxifangshi.html

creality3d@hotmail.com

I think you should ask the Creality 3D to send another pcb to you(because they supply one year warranty for microcontroller boards), or you can buy another one from them.

I tried locating them, but I couldn't find an email address or any other contact info for Creality. I'm going through GearBest, since it is where I purchased the printer from. GearBest says that they are not getting a response from Creality either. I a m so sad and embarrassed that I paid so much for something that doesn't work and all of my friends keep asking if I have printed anything yet. They would probably buy one themselves if I was successful, but they are surely hesitant to buy ANY 3D printer from anyone now. Do you have contact info for Creality?

That's impossible, because the service of Creality is very good. I think GearBest cheated you. Because I am also his one of distributors , I know they're very responsible for they're products. Do you have QQ or Wechat ? or I can help you get the email? BTW, where is your location?

I live in Milwaukee, Wisconsin, USA. I don't have either chat App , but I am downloading WeChat now.

I really like the product except for it not functioning.

Michael Haller Give me a little time, I will give you his Wechat ID. You can chat with him online.

Thank you for your help.

WeChat ID: Creality-3d

Well, I finally had time to try the suggestions given to me. I preheated the hot end and, yes, the Extruder works and also the laser. Why does the laser work only after I preheat the hot end and/or bed?

My filament does not lay on the bed. I assume the hot end is to far away from the bed, so I'll look into making sure it is closer. 0.1mm?

One paper thickness, making sure the paper between the hot end and the heat bed is easy to pull, but also not tightened or loosely

Ok and thank you so very much for helping previously. I was so distraught before and now I am humbled by my stupidity about the preheating.

Preheating is not necessary to make laser work. You can try to set fanspeed to 255, then the the laser will work.

Wow,thank you. I'll try it. I finally printed my first 3D print after adjusting the bed from the hot end to one piece of paper thickness. It is not perfect, but I will figure out what went wrong. Thanks again for all of your fine help and great advice.

How many steps per mm does the CR-8 take? If you have any more critical information for setting up CURA for use in making my own designs I'd appreciate it. Thanks.

My CR-8 Printer is not recognized by my computer when I have the USB plugged in. Do I have to do everything from the SD card?

Maybe your software setting in NB is different from CR-8 firmware. You should ask Creality 3D

hi bro, can you list your questions in one post by 1,2,3..? I can't figure out whats the main problem you are in.

I guess my main question is: what settings should be in CURA for the CR-8 3D printer?

Yes. The program that operates the CR-8.

Hi, I am the owner of CR7/8/10 group.
Quick question for you.
Do you know the control of extruder must do the preheat first?
You have to heat the heating-head up to 185°C then control the extruder.

Here is the SOP.
1. Go home of all axis
2. Preheat PLA
3. move axis 0.1 -> E

OK, I'll try that. I need to have it preheated even before I move it manually? It will be wonderful if it's that simple. It may be a few days before I find the time to try it. I'll let you know ASAP. Thank you.

Yes ,you need to preheat the pla , before you want to move the E motor .