ATOM 3D Printer Group 造訪社團 » EX

卡

請Pm，謝謝

請私，謝謝

請私，謝謝

請私訊，謝謝

看起來很不平整，是不是平台校正時，那條長長彈簧又影響結果？先拿掉做校正試試

謝謝熱心回答!校正測試前，彈簧都有拿掉，所以彈簧問題可排除

嘗試更新韌體看看，然後做50x50校準

謝謝您的回答!韌體也早已更新為 Atom 2.0.5b韌體，所以應該也不是韌體問題

可以看看Y軸連桿球頭皮帶光學極限是否鬆動。

校正要確每個點，都落下到盤面，我一開始也是同症狀

謝謝!應該是校正這問題,不是用自動校正跑一次就好?還是應該多跑幾次?或手動逐點校正調整?新手上路，請多指教!

好奇的是為什麼不上玻璃？

新機就要墊華司，有點怪ㄡ

樓主可以搜尋社團關鍵字「自動校正」喔

謝文祥 謝先生您好！我們現在的干涉問題都已經從設計上去改掉了，理論上不會有問題，不過保險起見，是否可以讓我們明天派快遞去把整組噴頭組+效應器取回公司檢查呢？不會向您收費只是耽誤您時間不好意思

真的是如Kuo Van所言,主要是螺帽和風扇磨差到上蓋，卡住彈不回去，造成限位開關無法靈敏感測，而校正錯誤

好的,麻煩您!

軟性磁鐵板已慘不忍睹

送回原廠處理，已解決

Try this first.
https://atom3dp.squarespace.com/extrusion-problems-1/#head5

Ah yes, I completely forgot about the PID settings. I have done that before and I know it takes a while.

Unfortunately neither Pronterface nor Simplify3D want to connect to the printer - the connection sends back garbage characters and I get messages like "could be invalid baud rate" and "connection failed". So I'l have to fgure otu what's going on with that first.

I just delete m109 in my g-code and start printing.
And newest firmware is 2.5.

2.5? Where does that come from? I got 2.0.7 from the Atom website. Is there a better place to find it?

And if you delete M109 how does the printer know to not print with a cold hotend?

http://www.atom3dp.com/....../2017/11/ATOM-2.5B-170116.zip

You can use this on 2.0

You just reach temperature and start printing

Thanks for your suggestions; I have some interesting results:
1. Firmware 2.5 did not work for me. I installed it OK and took out the M109 command. When I started the print the printhead started printing about 2 inches above the print bed and the hote nd was not at the proper temperature. No filament was extruded from the hotend.
2. I added an M104 to set the temperature to 215 and then tried to run an AutoLevel (which I had run OK before with 2.0.7), but the printer made a loud buzzing sound and didn't do anything. I took this as my clue to revert to 2.0.7.
3. I reinstalled 2.0.7, performed an AutoLevel , removed the M109, and verified there was an M104 S0215. When the printer started printing no filament came out. The LCD said the temp was something like 67. I took this to mean the hotend had not yet got up to the 215 temp.
4. I restarted the printer and did a warmup to 200. When I started the print this time it did in fact start printing - which it is doing now. I'm printing a string test part and using the same slicer settings I've used in the past the print is showing much more stringing. But it is printing the layers at 185.
5. I don't understand why Arduino can talk to the printer OK, but not Pronterface or Simplify3D.
6. I thought I could use the printer LCD to set PID values by hand, but I looked in the Configuration.h file and there are no defaults there for Atom2. I didn't think it wold be wise to use values from a different printer.

I resolved the serial port connection problem by setting S3D & Pronterface to use a baud rate of 250,000 and the Serial Port driver to a baud rate of 460,000. I have no idea why this solved the connection problem, but it did.

I ran the PID test and go t numbers KP: 17.63, Ki: 1.27, Kd: 61.25. The first 2 were fairly close to what the printer's LCD screen showed, but the last one was far different. At any rate, I stored the updates and did a preheat 200.

I was disappointed to see that the printer could not get the hotend to a temp higher than about 190. But I ran my string test print again, removing the M109 line since I knew the printer could never get to 215.

The print failed shortly after it started with what appears to be a jammed nozzle. I'm thinking the problem may be that the hotend I'm using has a heatsink just above the nozzle (it's like the original Atom 2,0 hotend assembly) and this may be preventing the heater disk from getting the hotend up to desired temperature. So I may go back to using my "newer" hotend which is similar to the current 2.5EX one.

Edit: Yup - if I stop the heatsink fan from running the hotend gets up to 200 quite quickly. Letting the fan go results in the temp goes back down to around 190. Looks like I really will go back to my previous hotend configuration.

Hi! I have had the same issues as you with the 2.0.7 firmware. The temperature fluctuated all time, so I went back to the 2.0.6 firmware

I am going back to 2.06 also because 2.07 does not allow negative Z-Offset values.

2.06 working fine - no need to redo PID values.

i also have problem on heating today, i found out my heater's wire snap.

好久沒有用Silic3r了，找時間研究看看

懶人 伸手求分享 覺得想玩...

給！
https://github.com/prusa3d/Slic3r/releases

幾乎都用 Default 值就可以開印了，不過可能會覺得它跑很快，可以從 50% 執行速度開始試。用過後有回不去的感覺！期待主版的 Slic3r 1.30 版快快發行，很期待 Adaptive Layer Height。

我想要超夢XD

牽絲好少，可以分享一下如何控制嗎？

這支撐真是重本.....撐的好實在.....

原來要撐到這麼密!!!

呃～Slic3r 丟在桌面超久沒用了說～

阿童 Cura 3.0真的弄不出來嗎？

這是神的領域！神的語言............太厲害了！我真的試的很認真的要看懂你們的內容，無奈程式語言真的是我的罩門！

阿童晚上不下班 ?

先把熱敏線和加熱片先拔掉看看，再開機。

電線破皮短路

短路 +1

更換過熱敏電阻問題已解決謝謝各位

不等出光固化模組，一魚多吃？

嘿嘿嘿!最近有想玩的機台，等出模組有點慢，我先跳槽，如果別人家不好玩再跳回來

私

私

有人反應價格太貴，那就再降個1萬吧。

目前已經有人預定了，謝謝

有可能是線壓到或是碳纖桿磁力干擾
可以卸下磁桿然後從溫度那邊設定fan speed看看會不會轉

看看你的連桿的正負極一下

看起不錯旳好機器, ? 我出價 2.5 萬

現在不拔出來,以後壞了要换管子還是要拔

加熱噴頭後, 拿木頭螺釘, 旋進鐵氟龍管, 拉螺釘帶出鐵氟龍管!