Anycubic Photon Printer Owners 造訪社團 » CLI

原文網址 Joseph Daniels
2020-02-14 20:27:00

All right, we know the little "clicks" are OK for the first bit of a print, but what about throughout the WHOLE print? I get the feeling I'm setting 0 too low on my S. Might explain why I got two good prints, then the rest have been total failures...

翻譯年糕

Nipuna Gunarathne
2020-02-14 20:50:00

Scott Pavlich
2020-02-14 21:19:23

原文網址 Chris Visser
2020-02-14 04:04:26

Has anyone heard any more about that Anycubic wash and cure station? I’ve seen a couple of YouTube clips for it.

Typed Anycubic curing station into eBay and only got printers as a return.

翻譯年糕

Clifford Schwankner
2020-02-14 04:19:33

John Giardino
2020-02-14 09:20:46

Clifford Schwankner
2020-02-14 09:24:56

John Giardino
2020-02-14 11:27:35

Chris Visser
2020-02-14 12:03:43

原文網址 Lorne Bixby
2020-02-13 21:41:28

Can anyone explain to me exactly what to click to download the resin exposure file from the photonster github page...

I don't understand github at all ?

翻譯年糕

Bill Connelly
2020-02-13 21:46:15

Falcon Tom
2020-02-13 21:46:53

Derek Reihe
2020-02-13 21:53:51

Sen Kun
2020-02-13 22:23:09

Lorne Bixby
2020-02-13 22:28:07

Lorne Bixby
2020-02-13 22:28:17

原文網址 Daniel Quinn
2020-02-12 05:08:26

So what's the deal with this print failure? This is 0.03 height, 8 bottom layers, 60 bottom exp, 5.25 exp on a Photon S (Anycubic Grey). Bed has been level as I've printed several other things just fine, FEP is new (I had replace it two prints ago). I stopped the print so that's why the sword is clipped, but the cape is all wonky. (Keep in mind she is globby because I didn't bother to wash her off in IPA.) Something wrong with my supports (placed manually)? In Validator I had a handful of islands with less than 10 pixels off.

翻譯年糕

Daniel Quinn
2020-02-12 05:09:58

Ryan Shelvik
2020-02-12 06:06:11

原文網址 Adam Rodgers
2020-02-11 06:50:03

Thanks for accepting me. I am a 3D sculptor and a client just sent me a Photon this morning as a surprise. As a complete non techy person expect me to ask for help a lot :) Will be unboxing tomorrow and setting the little beauty up.

翻譯年糕

Kyle McPherson
2020-02-11 06:52:11

Nipuna Gunarathne
2020-02-11 06:53:21

Adam Rodgers
2020-02-11 06:55:20

Hugh Jeriolas
2020-02-11 06:55:42

Roger Munguia
2020-02-11 07:44:28

Ryan Tudor
2020-02-11 08:55:28

Adam Rodgers
2020-02-11 20:20:53

Adam Rodgers
2020-02-11 20:31:02

Adam Rodgers
2020-02-11 20:31:06

Adam Rodgers
2020-02-11 20:39:01

Adam Rodgers
2020-02-11 20:42:45

Ryan Tudor
2020-02-11 20:57:37

Adam Rodgers
2020-02-11 21:48:59

Ryan Tudor
2020-02-11 22:00:19

Adam Rodgers
2020-02-11 23:26:40

原文網址 Jacob William Curtis
2020-02-10 09:53:23

First print complete! Leveled as the manual describes and everything came out pretty great. The docs on github were so great to get printing right away. Only issue is the support yanked a few pieces off the bottom when I was clipping it off. You live and you learn!

翻譯年糕

原文網址 Robb Nunya
2020-02-09 08:36:26

SIGH... So I have a new problem with my original Photon: My LCD started going out, so I replaced it. Yay, not an issue. The issue is that the Touchscreen lost the little cable clip that holds the ribbon cable from the mainboard... So I'm probably going to have to buy a new touchscreen. I hate having to do that, and the only place I've seen one is on Fepshop in the Netherlands. I'm in Texas. Bleh.

Does anyone know a part number for the clip? Or maybe a place in the US that sells replacement screens?

唉... 所以我的原創光子有一個新的問題: 我的液晶開始出門了, 所以我換了它. 耶, 不是問題. 問題是觸控螢幕丟失了從主板上的絲帶線的小電纜... 所以我可能得買一個新的觸控螢幕了. 我討厭這樣做, 我唯一看到的地方就是在荷蘭的fepshop上. 我在德克薩斯州. Bleh.

有人知道片段的部分號碼嗎? 或者在美國出售更換螢幕的地方?

· 查看原文 · 為此翻譯評分

Austin Dickinson
2020-02-09 08:55:50

Zeb Christmas
2020-02-10 13:08:19

Robb Nunya
2020-02-10 13:30:26

原文網址 Martin Špaček
2020-02-07 01:58:51

Hi, I need help. I have just wanted to try my firs print, but after a software update I can’t start test print, after clicking on file printer every time freezes. Any suggestions?

翻譯年糕

原文網址 Ranyle Singh
2020-02-05 16:54:53

Alright. I have used the search function and i just need some confirmation.
Made and designed this stamp for a client. (Not the logo, vector was supplied)
It's 65mm high and 32mm in diameter. came to 30ml of resin in anycubic black.
From what i have read, am i right to charge around $30?
$1 per/ml...

(Yes i know it's not mirrored imprint ? )

翻譯年糕