Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Adam Rodgers
2020-02-18 05:20:51

Hi again everyone - first print was 95% success - Photos in a day or two when I have done some more and organised myself. The first print fail area showed me that auto support needed help but my shipped software was Workshop v1 and did not allow tweaking of auto supports. I dled 64 bit Slicer after a recommendation here but the printer could not see files? JBearR suggested it only sees Fat32? Thoughts/facts? ONTO test print 3 - which is the Dog Solider seen in image - I have done one already and now want to manually optimize. So I just dled the updated Photon Slicer v1.3.6 which seems solid. Question - as a 15mm and 28mm Sculptor - I have pushed the layer thickness down to .03 on my way to .01 later. Do I need to tweak NExposure/Off Tme etc? I guess there is no right answer but I would like to hear thoughts and reasons if possible:) Attached is the auto supported image just so you have rough idea of what I am printing. This is not my final version, just a quick open file and play to see software worked and could tweak auto supports - THAT SAID - advice on angles and aspect etc always appreciated. Thanks people... Oh I also dled Validator which seems great too.

翻譯年糕

Paul West
2020-02-18 05:31:19

Nathan Carter
2020-02-18 05:32:29

Paul West
2020-02-18 05:33:06

Adam Rodgers
2020-02-18 05:41:57

Adam Rodgers
2020-02-18 05:42:42

Paul West
2020-02-18 06:16:55

Adam Rodgers
2020-02-18 06:30:52

Adam Rodgers
2020-02-18 06:32:17

Adam Rodgers
2020-02-18 06:32:46

Paul West
2020-02-18 06:37:06

Adam Rodgers
2020-02-18 06:37:23

Adam Rodgers
2020-02-18 06:39:43

Paul West
2020-02-18 06:40:15

原文網址 Adam Rodgers
2020-02-15 18:15:05

Hi ladies and gentlemen. Joined a day or three ago when a client sent me a Photon as a surprise :) Finally found the time to set it up and ready a print. I have set the auto supports to 'Thin' but otherwise used default settings across the board - just wanted to get thoughts on how this looks, too dense? obvious issues? I am not too worried about rear details at this point, I just want to find a baseline to work from. Thanks in advance.

翻譯年糕

Arthur White
2020-02-15 18:50:12

Arthur White
2020-02-15 18:52:46

Adam Rodgers
2020-02-15 18:54:19

Adam Rodgers
2020-02-15 18:56:21

Arthur White
2020-02-15 19:04:01

Arthur White
2020-02-15 19:07:15

Arthur White
2020-02-15 19:10:48

Adam Rodgers
2020-02-15 19:24:31

Adam Rodgers
2020-02-15 19:27:21

Adam Rodgers
2020-02-15 19:28:27

Arthur White
2020-02-15 19:40:30

Arthur White
2020-02-15 19:42:42

Arthur White
2020-02-15 19:43:15

原文網址 Adam Rodgers
2020-02-11 06:50:03

Thanks for accepting me. I am a 3D sculptor and a client just sent me a Photon this morning as a surprise. As a complete non techy person expect me to ask for help a lot :) Will be unboxing tomorrow and setting the little beauty up.

翻譯年糕

Kyle McPherson
2020-02-11 06:52:11