Anycubic Photon Printer Owners 造訪社團 » LCD

原文網址 Dylan VonDanger
2020-01-24 07:03:21

I have no idea how it may have happened, but the acrylic block that sits under the LCD screen on my printer is cloudy and affecting prints. Tried cleaning it off and just ended up scratching it. Anyone know where you can get a replacement? Reached out to AnyCubic support about this too but they're off until February 1st

翻譯年糕

Cody Wishart
2020-01-24 07:09:04

Dylan VonDanger
2020-01-24 07:11:12

原文網址 Joseph Covington
2020-01-23 16:37:12

Anyone try this yet? Seems potentially awesome

They say don't use IPA to clean which would make me think details could be lost? ? Just spray clear coat on it. You have to rinse it wouldn't you or could it be a formulation that drains residue easily?

IFUN 3D Printer Resin Clear 405nm HiClear HiTemp LCD DLP Printer SLA UV Cure 3D Print Liquid Photopolymer Resin Transparent 500g

翻譯年糕

原文網址 Justin Cowing
2020-01-23 06:31:51

Has anyone experienced a few of the I’ve leds going out? I thought it was my led screen but I’ve replaced that, only to notice while it’s all opened up that only 2 of the leds are lit during the uv test. When I shine a light through the lcd screen I see that it’s actually working fine.

翻譯年糕

原文網址 Blaine Tsukayama
2020-01-23 01:04:00

Anyone know what are the alternative replacement LCD for the original photon?

翻譯年糕

Glenn Lambert
2020-01-23 01:08:45

Hugh Jeriolas
2020-01-23 01:16:09

Patrick Stark
2020-01-23 01:29:01

Blaine Tsukayama
2020-01-23 02:20:00

Denlee Paddy Rhodes
2020-01-23 02:26:53

Blaine Tsukayama
2020-01-23 02:32:39

原文網址 William Holmes
2020-01-22 21:44:52

Just finished printing these guys. Have a weird artifact at the same height across all 3 models. Middle model the support failed. Checked the original model and doesn't show anything. Possible lcd failure? Machine is only a couple weeks old. Supported in prusa and sliced in chitubox. Any ideas?

翻譯年糕

William Riker
2020-01-22 21:46:55

William Holmes
2020-01-22 21:49:05

William Riker
2020-01-22 21:50:24

William Holmes
2020-01-22 21:51:07

Matt Reed
2020-01-22 22:01:25

William Holmes
2020-01-22 22:14:34

Lisa Perkins
2020-01-22 22:24:56

Jim Monaco
2020-01-22 22:31:10

原文網址 Lorne Bixby
2020-01-22 20:40:10

Caught a print failing early on and I stopped the print. Pulled the vat and the LCD screen popped up with it... Now it's not sitting flush. Does it just drop in and push fit ?

翻譯年糕

Ryan Mitchell
2020-01-22 20:56:16

Lorne Bixby
2020-01-22 21:38:03

原文網址 Jacob Bolton
2020-01-22 20:18:38

So hypothetically if I wanted to add a larger tft lcd print screen to my printer would anyone know the best direction or who would be best to buy from?

翻譯年糕

Tom Krüsi
2020-01-22 20:23:03

原文網址 George Jones
2020-01-22 17:03:57

I have a somewhat unique problem. My photon is in firmware 4.2.17 and works perfectly. However, when I update to 4.2.18/9 the LCD suddenly goes crazy. Attached is a video of me upgrading the firmware, any advice?

翻譯年糕

Ramiro Montes De Oca
2020-01-22 17:32:00

George Jones
2020-01-22 17:36:18

Chris Holden
2020-01-22 18:08:31

Marc de Hoogh
2020-01-22 18:28:21

George Jones
2020-01-22 19:21:07

George Jones
2020-01-22 19:21:31

George Jones
2020-01-22 19:27:39

Marc de Hoogh
2020-01-22 20:08:59

George Jones
2020-01-22 20:45:44

Chris Holden
2020-01-22 23:49:08

Dobromir Kowalski
2020-01-23 00:18:06

George Jones
2020-01-23 04:50:51

George Jones
2020-01-23 04:52:17

Dobromir Kowalski
2020-01-23 05:01:45

George Jones
2020-01-23 05:03:12

Dobromir Kowalski
2020-01-23 05:08:56

George Jones
2020-01-23 05:09:58

George Jones
2020-01-23 05:10:42

Dobromir Kowalski
2020-01-23 05:12:56

George Jones
2020-01-23 06:13:52

原文網址 Dillon Olney
2020-01-22 11:49:44

I keep having this issue on the right side of the printer. Tons of odd layer lines and these strange goopy sheets of odd printing mayhem. I changed the fep, releveled, reshootkand filtered the resin, cleaned out the vat and still this.... looks like a potential lcd issue? But I just replaced that a few months ago...

翻譯年糕