Anycubic Photon Printer Owners 造訪社團 » LCD

Am I crazy or is this new screen not working right? I ordered two elegoo mars screens Because my photon one has developed a burnt out section. Neither one would display the exposure test on the lcd so I thought I just got two bad screens and returned them to amazon and ordered one direct from Anycubic. But this Anycubic one isn’t display the exposure test either. Did I mess something up?

翻譯年糕

should the tempered glass cover on the front of https://www.amazon.com/ELEGOO-Resolution-Protection-LS055R1SX04-Compatible/dp/B07X586JHK/ref=sr_1_2?keywords=ELEGOO%205.5%27%27%20Inch%202K%20LCD&qid=1575284714&s=industrial&sr=1-2&fbclid=IwAR3frC7ndvGPRJS5GvY5eFCRL59i5Qg1rRY_3MmHYVct5m42Ujm_0_1cvqU flex?

got one of these from a supplier swapped it into my photon, small object print ok bu anything larger that presses down on the screen I am getting flaking on layers I tried doing a test print om a larger print that covers more are of the screen and I start getting repeat issues with flaking..
When I try using my old LCD with light showing through on it my print comes out just get some resin cured on the bottom of vat..

I removed the new screen and inspected it and suddenly saw that the one I got the supposed tempered glass is nothing more then flimsy bit of plastic even slightly pressing on it bows it and the LCD under it..

When even slight pressure in center bows down the screen from the print bed.
Should I demand a refund? 翻譯年糕

Quick question:

LCD died. Amazon has the elegoo screen on for a lot less than the anycubic one.

Are they interchangeable?

翻譯年糕

My latest video. Hope it helps someone ? Enjoy!

Know why and when you will need to replace the LCD on your Resin SLA Printer!

翻譯年糕

Anyone know where to get LCD glass protectors quickish? UK.

翻譯年糕

one of the photonsters 'known issues' is "Z motor stops moving mid-print, LCD keeps exposing resin, no error message, stopping print and moving Z via menu works."

anyone know if there are any firmwares that fix this? it's happened 3 times now, frustrating.

翻譯年糕

Hey hive mind. Having an issue that i haven't had before and need help, happening in the last few days. Using anycubic trans yellow. Ive printed this peice a dozen times without supports, and had this issue on other prints. I have... retuned fep screen was a bit uneven and at 220 now at 330. Releveled and cleaned tray. Tried different usb sticks. Checked lcd screen runs fine, cleaned screen. The problem keeps happening in the same place on the tray, Items on the right print better. Tried in updated chitubox and verfied. The ring on the left are slight indents in the fep but has never caused an issue

翻譯年糕

Greetings,

While I understand most of the information available on photonsters is geared towards the original Photon, and for good reason, I own an S and after a few test prints I have some doubts about what could be the optimal work process to get the best of my prints.

While using Photon Workshop 2.1.19 I notice that, if I change the machine from the S to the original Photon, I see that the final calculated times to print change noticeably. About 10-20% slower with the .photon file against the .photons file. Are these differences in calculations accurate? Does any real difference exist if I use one kind of file over the other with the S? I know there are a lot of utilities that need the .photon and that makes it more interesting, I mean about straight printing differences between formats.

To my understanding, Chitubox is a more desiderable alternative. Is the machine configuration for chitubox for the S the same as for the original Photon? 1440 x 2560 px, 68.04 X, 120.96 Y, 150 Z, LCD Mirror?

I've seen the exposure calibration set is not working on the S as you cannot currently execute the gcode file on it. Any recommendation on how to fine-tune the exposure times beyond the city test print? I can tell apart if the piece is underexposed fine enough, but I struggle with overexposure. I even think that in the documentation the overexposed print looks better

Thank you very much

翻譯年糕

PHOTON or MARS? (question for those that own BOTH)
So I have owned the Photon for 4-5 months now. It is decent. My prints are still hit or miss. Probably my fault. But I've had to replace the LCD, and I have had to re-level it, and it is looking like it needs leveling again tonight from some thing odd that happened to this morning's prints. Otherwise, I have enjoyed making stuff on it. Even made a little money making cool stuff for people.

I would like to get a second machine... But I am not sure if I want another PHOTON or not.

QUESTION for those that own BOTH Photon and ELEGOO MARS..... would you recommend the MARS orver a second Photon?
Why or why not?

THANKS!

翻譯年糕

Just need a paint now, new lcd and Playing around with my new dslr.

翻譯年糕