Anycubic Photon Printer Owners 造訪社團 » LCD

With the new LCD installed I've finally made a successful print! Post curing I've noticed these white areas on some places. What could cause these?

翻譯年糕

Hello everyone!
I've got a problem with my lcd-screen (I think). Everything was good before. Last print was 3-4 weeks ago. And this time I got a brick of resin instead of my pretty tabletop miniatures.
The test doesn't show the rectangule.
Found some other test on github but everything also failed.
Already wrote to anycubic support, but maybe someone knows how to fix this.
Thanks in advance.

翻譯年糕

Hello, 3rd LCD that I received. Did the UV test and here is the result. Any help ? Ty.

翻譯年糕

I was doing printer maintenance installing new LCD screen and also FEP film on bottoms of vat.

Was pretty focused on installing the FEP with no distraction and suddenly my cell phone messenger and also computer rang in a group call...

Needless to say I was startled by the sudden ring loud ring out of nowhere the driver slipped and almost punctured the FEP.

its very thin in the area and I am worried If I print something the bit sticking up will get cured in a print and when lifts will pull and tear. .

Still safe to use?? or wait until another one arrives?

I have put water in and tested and there is no leakage..

I am wondering if I arrange prints so nothing is cured on that point would it be safe has anyone else gotten dings like this before?

翻譯年糕

After a couple of months I had finally time to install the new LCD that Anycubic were kind enough to send me. The good news are that I have managed to install it and the UV test shows that my old screen had some problem so that was ** possibly ** what messed up my prints. While the LCD was off I had noticed a marking on one of the UV LEDs. I removed the heat-sink to take a better looks and there is visible crack on the lower right LED's lens. Now the question is - will this mess up my prints? I did not try to print anything since changing the LCD a short while ago because I ran into a USB thumb drive situation need to get a new one at the store tomorrow :) Please let me hear your opinions. Thanks!

翻譯年糕

So I received my Photon in the mail last week and finally, this weekend, got the time to set it up and start printing. I immediately ran into issues when I began the setup. My LCD screen was not displaying the rectangle test frame as shown in the users manual. After an hour or two of searching the internet with no real success on finding advice, I opened up the base to check the cable connection. It was connected just fine.

As a next step i chose to completely remove the LCD to check the connection to the screen itself and found the issue. The connection of the screen was torn. Has anyone else had this issue after delivery? What do I do?

翻譯年糕

i was thinking about updating my firmware on blue window photon(iv got v4.0.11_lcd).i see a lot of people recommend 4.2.18 from github,but i see only 2 files in the zip and not 3

翻譯年糕

I'm getting some fierce layer shift lines. I've used a few resins but this sample below is from Using ELEGOO 3D Rapid Resin LCD UV-Curing Resin 405nm Standard Photopolymer Resin . I was told that my plate might not have been tight creating 'suction' or that my build dish might not have been tight. I checked both of those and tried a new print and had similiar results.

I was also told that I might not have enough supports so I increased the supports.

Are my settings way off? They are tilted at 45 degrees or at least are supposed to be according to Chitbox which I'm using to cut and add supports. 翻譯年糕

Need some help from the hive! Last couple of prints my build plate stop moving on the Z axis but was still going through the print but as I couldn’t find any resin hardened in the vat I think the lcd also stopped but on the front panel screen it was still going through the print. Any ideas?

翻譯年糕

I have been having issues with cured resin in my vat for a while. I tried everything I could hoping that I would not have to replace the LCD screen but thats what I had to do. I was pretty stressed out about it and picked up a $20 Elegoo screen off of Amazon which some people reported having problems installing. I just put it in and I am happy to report that it wasn't that hard and worked right away. Test print will be starting in a few minutes. (Yes, I know the protective plastic is still on in the pic.) https://www.amazon.com/gp/product/B07X586JHK/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 翻譯年糕