Anycubic Photon Printer Owners 造訪社團 » LCD

why do I have to be the odd one out. when everyone else`s faulty screen shows random blocks and strange patterns but mine is just pure black. No leaks of resin. no failed prints pressing into the glass deforming the lcd, No firmware/fan issues on the latest firmware. But now I am the proud owner of a fubar lcd. at least I can get to inspect it now.

翻譯年糕

SQT: where can I get cheap replacement LCD screens for my Photon? Preferably shipped within EU. Also, Cheap FEPs would be nice. :) SQT: where can I get cheap replacement LCD screens for my Photon? Preferably shipped within EU. Also, Cheap FEPs would be nice. :) 翻譯年糕

Any ideas on what could cause this void. I've printed 2 and in between each print I've printed other things just fine. I've checked the FEP and the LCD screen both are good. Could it be a corrupted file? I've used the same exact file. It's hollow with 3 drain holes. Machine is in a large closet with temp at 74°F.

翻譯年糕

So, I need some help. There are huge holes in the model, and the end of one of the eye stalks is all warped and delaminated.
I've gotta say, it is pretty frustrating. I checked the LCD, it is fine. The screen is clean, I just don't know what happened here.

Tightened the FEP to 330, leveled just fine, exposure should be good. The hole in the model is only at that point, it doesn't extend all the way through the model, and the delamination/skewing of the model doesn't make sense to me.

翻譯年糕

Hello. I would like to know if this has happened to anyone, or can anyone help me. I have Photon about 4 months ago, and until today the machine has been little used. Everything was working perfectly when the machine reported error T_88. I saw on Github ( https://github.com/…/ma…/known-issues/photon-known-issues.md ) that the problem would be on the LCD screen. After this machine also accused error L_10 a few times, and this error is not found on the internet. Even after this happened Photon kept working, sometimes printing stopped and sometimes it stopped, showing the error screen but with the option to continue. Pressing play often continued printing normally. A few weeks ago Photon stopped working. The LCD screen no longer shows the rectangle during the UV detection test, the entire screen turns blue. Already tried to change the firmware and nothing has changed. I contacted Anycubic, and they sent me firmware 4.2.5, this firmware ended up generating a "Machine Errer Code Status" file, which I sent to Anycubic to analyze. At first they told me that the error would be on the motherboard, then they told me it would be the LCD screen. My Photon is still in the warranty period, but since I can't stand still waiting for the LCD screen from China to Brazil, I ended up asking a friend of mine to bring a screen from the United States. Yesterday I changed the LCD screen and could see that the error was not the screen because the printer continued to have the same problem. The LCD screen turns totally blue. Does anybody know how to solve this? Thanks in advance

翻譯年糕

Silly question of the day... I've got a bunch of STL files (parts of a larger model) and I'm arranging them, adding supports etc in Chitubox. I've got all the remaining parts off the grid to the side of the printable region so I know which bits I've done, which I still need to organise.

I can fit all the parts onto 3 print runs, but will it cause printing issues if I leave the unused parts off to the side of the project in red? I'm assuming that because the LCD only covers the printable region, then when I generate the sliced file it will only generate the bit that needs printing, right? Or is it going to cause my printer to go into spasms? TIA!

翻譯年糕

Recently in installing a new 2K LCD screen under warranty from Anycubic on my Photon, my main board went bad.. and in a series of emails.. the clip on the front touch screen clip broke where the ribbon clips in from the main board. So Anycubic sent me a new main board, a new front Touch screen (had me keep the 2K LCD screen they sent to me) and two new fans as they were both making noises (I installed the lower fan (that vents the electronics chamber but have not been able to install the "filter" fan from the resin chamber yet as I am not figuring out how to do. So, I followed the instructions for installing the main baord for the Photon too. But now I got a white lit up blank "front LCD touch" screen on the front of the Photon.. so I can't even test the rest of the installations with the main board and the 2k LCD screen. ? 翻譯年糕

Good news on the LCD front! Elegoo just announced that by the end of the month they will be selling LCD’s on Amazon compatible with the Photon, Epax, Mars and all compatible machines for under $30!!

We have so needed this on a consumable product!

翻譯年糕

Anyone else experience the LCD printing half or full screen snow/static? It randomly happens, I've printed the same stl multiple times and it starts randomly, even if part of the print is successful it leaves a sheet of cured resin on the fep film the exact size of the LCD screen. I've changed my USB and resliced this particular stl I'm experiencing this with but it continues to happen. I'll try to take a picture when I see it again, but I'll include one of the sheeting I'm seeing.

翻譯年糕

I recently bought some Kapton for my LCD after I saw a post a few days ago where someone taped the edges of their LCD screen in case the FEP broke and leaked resin into the LCD screen. I just want to make sure that this is something I can do and will not effect my prints. Any thoughts?

翻譯年糕