Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Bruce Barton
2019-12-19 15:15:48

So it worked. A 2 color medallion. Printed in Aqua Blue, set with Clear.

Lessons learned:
-Need a sturdier tape to secure to the bottom.
-Use less fill in resin due to thermal expansion.
-400 grit is not enough to polish.
-Wet sanding is much easier on your lungs.

翻譯年糕

Mae Mei Bidlake
2019-12-19 15:28:39

Bruce Barton
2019-12-19 15:29:45

Mae Mei Bidlake
2019-12-19 15:32:00

Johnny Wee
2019-12-19 19:06:40

Neil Ramsay
2019-12-19 19:51:01

Cody Ray Pierce
2019-12-19 22:10:05

Bruce Barton
2019-12-19 22:15:37

Jim Carswell
2019-12-20 05:57:48

Bruce Barton
2019-12-20 06:03:25

原文網址 Bruce Barton
2019-11-25 10:33:49

So am I burning the resin in the curing station? Don't seem to remember if the dots were there before. (Back side on the bottom.)

翻譯年糕

原文網址 Bruce Barton
2019-07-30 11:41:40

So what kind of UV resistant clear coat should I be looking for? The lady at the paint store had no idea what I was talking about. So what kind of UV resistant clear coat should I be looking for? The lady at the paint store had no idea what I was talking about. 翻譯年糕

伟洪
2019-07-30 11:44:52

Andrew Gott
2019-07-30 11:46:45

原文網址 Bruce Barton
2019-07-28 05:11:41

Yummy...

好吃...

· 查看原文 · 為此翻譯評分

原文網址 Bruce Barton
2019-07-24 08:26:39

Anyone else having issues punching holes in Chitubox v1.5? It shows the column but it doesn't actually place a hole.

翻譯年糕

Kris Occur
2019-07-24 08:30:05

Bruce Barton
2019-07-24 08:30:40

Bruce Barton
2019-07-24 08:32:51

Eric Wilfreesboro
2019-07-24 08:32:57

Can Canino
2019-07-24 08:33:13

Kris Occur
2019-07-24 08:34:08

Bruce Barton
2019-07-24 08:40:34

Renato Gelmini
2019-07-24 09:11:30

Mark Wardle
2019-07-24 10:15:48

Rob McEwen
2019-07-24 10:23:51

Joel Evan Betker
2019-07-24 12:44:28

Richard James Sanchez
2019-07-24 16:19:10

Gary Houser
2019-07-24 21:42:51

原文網址 Bruce Barton
2019-07-20 00:58:11

So I printed the Elegoo Rooks as a test. The pieces turned out pretty decent. I used an ultrasonic bath with Mean Green for 300ish seconds, then rinsed in a secondary bath. I bought a cheap UV nail light which may have been too cheap. So I fashioned a tub of UV LED strips. After passing out and leaving the light on the turntable all night, I'm still left with sticky patches on the Rooks. Is this still uncured resin? Perhaps it's cleaner?

翻譯年糕