Anycubic Photon Printer Owners 造訪社團 » Anycubic

Also does anyone have any recommendations for priming ? Iv never used the spray before so i dont know if there is a best practice for it?

He is done!
Took about 60 hours
Made out of 7 parts
Took 6 drafts
Next step is priming and painting
Once its primed ill post another photo, the head is made from a head scan of me

Anycubic Green Transparent Resin

LT -0.02
BTC -3
ET -7.5s
BET - 40s
LOD - 6.5
BLOF - 6.5

翻譯年糕

Have members had good support from Anycubic? I ordered some resin on 2nd January and still haven't received it. I have confirmed I was charged, have an order receipt, but nothing more. No postage or processing updates etc. Since, no updates on my order page either.

Despite contacting Anycubic multiple times I don't even get replies... I'm unsure what I can do! I'd heard they were renowned for customer support.

翻譯年糕

Hi! How do i keep the "plattforms" from deforming? Tried to add extra supports but even at the support point the platform deforms. Anycubic photon zero with stock settings and anycubic gray. Only the base get deformed

翻譯年糕

I need some help.

all my prints are coming out clinging to the FEP.

Already level the bed

I've already increased the exposure time

and nothing works!!

Resin is Anycubic Green castable

翻譯年糕

Hi everyone,

I'm wondering if there are dentists in this group that uses the Photon S for printing models, guides, splints...etc.

1. Which resin do you use?
2. What setting do you use to print the appliances to get the accuracy?
3. Which software do you use to modify the STL? Is meshmixer and Anycubic Workshop sufficient?

Thank you so kindly for sharing your experience.

翻譯年糕

Is it alright to mix different colors of resin, such as Grey and White? Both from anycubic, but I'm running out of Grey and just have a bottle of white left. Still, I'd rather not waste what small amount of grey I have in my tank.

翻譯年糕

Anycubic Translucent Red

It comes out red and clear which I like and I used hot water to get supports off, used the washing and curing station to wash and cure and a small razor to shave down the bumps I’m just curious if anyone has any tips for models like these where you can either;

A. set up supports so they don’t leave marks
Or
B. Method to remove the divits without messing up the finish
Or
C. Any other methods by which to have an easier post part.

I used prusa slicer for optimizes orient and auto supports and manually added my own where need and sliced with the photon slicer.

Any tips or tricks will, I know a lot from research and the forums but obviously not everything.

I feel like I did an okay job removing the divots but you can see the scrape marks.

I’m aware there’s just no getting around the support removal sometimes but the forum knows best!

翻譯年糕

My Printer Anycubic Photon S when set USB Drive have a problem can't see file in drive ,how i can fix it ?

我的印表機任何立方體光子s當設定usb硬碟有問題, 無法在驅動器中看到檔案, 我如何修復它?

· 查看原文 · 為此翻譯評分

(Anycubic Photon Tools)

So I had to replace my screen. In doing so I accidentally knocked lose the ribbon to the build in control LCD screen of the photon. I have to get longer Metric T-Handle Hex Key Set tomorrow to be able to take the mother board out to to reset that wire properly.

Is there a place for this group that has a list for suggest tools and stuff to buy for working on the internal guts of your Anycubic Photon? Thanks in advance! ?

翻譯年糕

Switched to Grey when the green ran out. Everything seemed to be going okay. Until I noticed that a couple of the prints were pulled off the supports. And this Caster has some weird layering going on I'm curious if maybe all of these issues are not having my exposure correct? I saw the spreadsheet but I'm curious because I've read that the photon S needs shorter times than the original photon. Is there anyone using the anycubic Grey that would be kind enough to share this settings they're having for successful print so I can try again? Or maybe someone can tell me that I did something else wrong

翻譯年糕