Anycubic Photon Printer Owners 造訪社團 » resin

Hollowed this but forgot to put in drainage holes. Any suggestions on how to drain and cure resin on side the model.

翻譯年糕

I had a bit either not print or fall off during printing
Should I filter the resin? I had a bit either not print or fall off during printing
Should I filter the resin? 翻譯年糕

I like Siraya Blu, but my eyes burn being around it. Going back to Anycubic Green.

In the meantime, here's a big, beautiful print in Siraya Blu. The main body of a 28mm Scale Scorpion Mech. This thing is supposed to have 8 legs, pincers, a tail, and weapons all over it.

The glisten is from IPA, not resin, not to worry.

https://www.instagram.com/p/B839sbhnQXy/…

翻譯年糕

I tried castable resin orange model C1 of xyz. Printed on anycubic photon and the end result is good.

翻譯年糕

Is it possible to add glow in the dark material to resin????

翻譯年糕

Cross posted this help request to reddit as well, but want as much help as I can get :)

I'm having issues with parts warping inconsistently.
A run down of things that I've tried thus far are: Re-level bed (both paper and read method) Clean the plate and FEP Check that FEP is properly tuned Parts are angled 10ish degrees (depends on part exactly how much it's tilted) - Question on this later. Supports are auto support in Prusa Slicer then manually edited as needed. Here is a screen of the plate I'm currently trying to build: https://imgur.com/a/6ASRKE9 The two parts on the sides print fine, the center piece is my problem and warps severely and the supports are snapping off. Print settings: https://imgur.com/a/63IXEr4 Question about tilting parts... I understand that having the least amount of surface area contacting the FEP is optimal and that is why we tilt our parts, however the base portion of the supports is still flat and printing flat to the plate. Aren't we creating the same issue we are eliminating by tilting the part by having to put so many supports and essentially creating a flat raft on the plate anyway?
Edit: Using Anycubic Orange resin. 翻譯年糕

Big boy dragon test print using Eryone 3d clear resin is almost done. photon not skipping a beat. Brought home some big plastic sheets. Will be useful to protect my desk from the resins and the paints. Plus I got like 50 of them

使用eryone 3 d清樹脂的大男孩龍測試列印即將完成. 光子沒有跳過一拍. 帶回家了一些大塑料床單. 保護我的桌子免受樹脂和油漆的影響將是有用的. 另外我有50個

· 查看原文 · 為此翻譯評分

Need some advice.

My prints even after cleaning are incredibly sticky. There's almost no chance that it's residual resin because after a wash in cleaner, I'm curing these things overnight and then hit it even more with my UV flashlight for a good minute or two up close just to be thorough.

I'm assuming that it's the cleaner I'm using that's making it so sticky. I'm using the Mean Green that Uncle Jessey on Youtube recommended and a sonic cleaner (I saw the video about the heater and yes I'm no longer filling the tub with mean green or leaving the unit plugged in) but for now I'm just trying to make it not sticky.

I'm also driven to think it's the left over cleaner that's sticky because AFTER I cleaned it I thought "Okay it's safe to touch" and after handling it a bit, the skin on the tips of my fingers started to flake off a bit. A telltale sign that you're touching heavy-duty cleaning solutions. (Wearing gloves until I KNOW that it's clean now)

I've tried warm soap and water, cold water, washing it with IPA. Nothing seems to get this thing to not be super sticky.

I'm considering not using the green stuff anymore and switching back to 99% IPA. Give me your experiences/suggestions

需要一些建議.

打掃後我的指紋也非常粘. 幾乎不可能是殘留樹脂, 因為在清潔洗衣機洗完後, 我將整晚修補這些東西, 然後用我的紫外線更近一分鐘或兩分鐘.

我假設它是我使用的清潔劑使它變得如此粘. 我使用jessey叔叔在youtube上推薦的卑鄙綠色和一個聲波清潔器(我看到了關於加熱器的視訊, 是的, 我不再是, 我不再用粗糙的綠色或離開單元插上), 但現在我只是嘗試 讓它不粘.

我也被驅使認為是左邊的清潔劑很粘, 因為清理乾淨後, 我覺得"好吧, 它 是 安全 的", 處理一下, 手指上的面板開始脫掉了. 有點. 一個告訴你正在觸控重型清潔解決方案的跡象. (戴著手套直到我知道現在乾淨了)

我試過溫暖的肥皂和水, 冷水, 用ipa一起洗. 似乎沒有甚麼能讓這東西變得超級粘.

我正在考慮不再使用綠色的東西, 並切換回99 % ipa. 給我你的經驗/建議

· 查看原文 · 為此翻譯評分

Has anyone ever tried this resin? The description mentions jewelry. It also mentions high temp resistance so I dont know if it's just for modeling or can you use it for casting as well?

翻譯年糕

What’s the best Uv light to cure resin?
I was told a nail salon light for curing nails?
Thank you

治療樹脂最好的紫外線是甚麼?
有人告訴我用指甲沙龍燈治癒指甲?
謝謝

· 查看原文 · 為此翻譯評分