Anycubic Photon Printer Owners 造訪社團 » EX

原文網址 Jonathan Shih
2020-03-16 16:39:44

Tried to print again using my photon...
1. The upper side looks great, but I failed again on the back side...should I try using Prusa for auto supports?
2. Some of the heavy supports also merged. I may have under exposed a bit too am I right?
3. See fifth picture below, the whole piece distorted a bit from a certain layer. Not too sure how I can improve that...

Settings:
Slicer: Chitubox
Material: Anycubic ECO clear
Exposure: 11; Base Exposure: 55;
Layer height: .05

Supports setting as per 3DPrintingPro’s setting

翻譯年糕

罗西晟
2020-03-17 02:47:21

How (and when) are you removing your supports?

I can imagine you get those potholes by just tearing the supports off...

Also if you watch 3DPrintingPro’s youtube again, he tells you he puts the heavy supports to make it stick to the buildplate but that it also (could) damage the model... which is why he "hides" them on a side that is not seen...

Jonathan Shih
2020-03-17 09:10:47

Xi-Sheng Luo After printing I clean the print with IPA and put in under the sun for 15mins.

The supports are removed after that but I admit I did tear them off a bit (as they are a bit too hard...)

Sorry I’m a total newbie and made quite a bit of mistakes... will watch 3DPrintingPro again as I may have missed a lot of important bits from the videos...

罗西晟
2020-03-17 14:22:02

Jonathan Shih possible damage aside, if you remove the supports before curing in the sun, there should be less damage.
Still some, but less.

So: Print -> Clean -> Remove Supports -> Cure.

Jonathan Shih
2020-03-17 14:35:53

Xi-Sheng Luo thanks for your advice, still a long way for me to learn in this 3D printing journey...

原文網址 Ben Bicakci
2020-03-16 12:10:13

Has anyone else found some inconsistency in terms of colour and print quality/settings with Anycubic Grey lately?

I go through a few bottles of Anycubic Grey a month, and I'm finding every new bottle I open varies a bit in colour, ranging from the usual grey to a bit more bluish or greenish. And it seems to affect the printing too, sometimes I need to bump up the exposure up 1 sec or so.

翻譯年糕

原文網址 Eric Causeway
2020-03-16 11:09:22

3 failed prints in a row, and the fep got a small hole after the third failure

I used anycubic grey
74°f room temp

Edit the first layer or so of the print sticks to the build plate, and the rest sticks to the fep

Printed off the photon s

Edit 2
1st failed print
Bottom exposure 60
Normal exposure 7

2nd failed print
Bottom exposure 60

Edit 3
I've had over 30 or so successful prints with the settings I was using

Layer height.05
Normal exposure 7-10 depending on how big the model is

Off time 4
Normal exposure 10

Bottom exposure 70

Bottom layer 3

翻譯年糕

Stephen Colin Richie
2020-03-16 11:49:10

Autosupport?

Mark Wardle
2020-03-16 12:45:33

failing how. not sticking to the build plate no supports forming. or supports forming but no models. ? if not sticking to the bed. and you printed the test model ok. then dial up the base exposure by 10. and repeat if you need to. model not forming but base sticking to plate. dial up exposure by 2. remember resin settings are just a starting point you still need to raise or lower depending on printer.

Mark Wardle
2020-03-16 12:46:36

if you have a hole in the fep and resin is leaking best to change the fep sheet. and clean up any resin. filter the resin as you pour it back into the bottle incase of bits in the resin from failed prints. :)

Eric Causeway
2020-03-16 18:17:14

Mark Wardle the base layer sticks to the plate, then there seems to be an issue with he following layers sticking onto the fep

Eric Causeway
2020-03-16 18:17:27

Stephen Colin Richie nah I manually support.

Tom Sargison
2020-03-16 19:48:01

Check out my Newbie resin guide. Maybe it will me helpfull
https://www.facebook.com/groups/bod3d/permalink/239625677038736/

Darko Miljak
2020-03-16 19:57:00

Normal exposure time is waaaaaay too much, bottom exposure increase and bottom layer increase. It should be printable on the supports u made, IMHO resin settings are problematic

Eric Causeway
2020-03-16 19:57:20

I appreciate the guide, but it seems to be more trouble shooting and I don't have the time or read through all of that. I work a full time job, run my own business, and go to college full time. So I sorta need an answer that can be given to me in quick forum time or YouTube video.

Eric Causeway
2020-03-16 19:58:29

Darko Miljak my normal exposure for the first two prints that failed were 7 and 10 as per the resin anycubic resin guide. I bumped it up to the max that has had success per the guide and it failed again

So I don't think it's exposure time cause I've been playing with jt

Tom Sargison
2020-03-16 20:00:59

Eric Causeway Well we are all busy people) same full time job 3d printing busines, no collage (thanks god). But Solving issues needs time. Want it solved - find time. 3d printing troubleshooting is time consuming. In quick form i can onlyname 4 things: 1) Plate Leveling 2) Support settings 3) exposure settings 4) Slicer bugs (lost or currupt layers.)

Eric Causeway
2020-03-16 20:04:51

I level the plate after every print cause I'm paranoid like that

I manual support, and have been using the same setting for 30 or so prints. So I'm not sure that's the issue because I have had success each time prior

The tuning of the exposure has been changed after the first fail. I originally using settings from the resin guide. Then went to 10 normal 3xpisure. Failed. Then went 15 normal exposure and cranked bottom exposure up by 10

Tom Sargison
2020-03-16 20:05:58

Also i see that you got 2 types of heads but same heads have different supports patterns. And main problem that it is listed in my guide - You start suporting incorrectly! the ball joint is lowest point and it has only one support! You must have atleast 3 point near first object layers for a nice sturdy start

Tom Sargison
2020-03-16 20:06:51

Anycubic grey 60\7sec is correct. use 8-10 base layers count.

Eric Causeway
2020-03-16 20:13:14

So here are the settings I've used so far

Print 1 failed
Layer height.05
Normal exposure 7

Off time 4
Normal exposure 10

Bottom exposure 70

Bottom layer 3

Print 2 fail
Layer height.05

Normal exposure 10

Off time 4
Normal exposure 10

Bottom exposure 70

Bottom layer 3

Print 3 fail
Layer height.05
Normal exposure 7

Off time 4

Normal exposure 15

Bottom exposure 80

Bottom layer 3

Eric Causeway
2020-03-16 20:15:41

Why would it suddenly give me problems now? I've printed over 50 heads exactly like this :(

Stephen Colin Richie
2020-03-16 20:18:12

So, what's changed since your last successful print?

Eric Causeway
2020-03-16 20:20:05

Stephen Colin Richie nothing, same settings, I keep my house at the same temp, set the heads up like I always do with bits like this, same resin

Eric Causeway
2020-03-16 20:20:57

Is why this issue is annoying the snot out of me oh and I do the same exact dance that I always do what I'm shaking my resin bottle

Tom Sargison
2020-03-16 20:41:09

Eric Causeway a cant answer that. But 3D printing is a technology that doesnt come with any Guarantee =) It can work out this time but fail another time. Just a mater of case.

Chris Crute
2020-03-17 06:49:56

Sounds a little like the problem I posted about. How old is your lcd.

https://www.facebook.com/groups/AnycubicPhoton/permalink/1975105972634035/

Eric Causeway
2020-03-17 06:51:28

Chris Crute a month

原文網址 Mario Hippmann
2020-03-16 05:32:57

so i am about to buy models from gambody

but i worry, that the pieces wont fit because of SLA printing.

someone has experience?

翻譯年糕

John Yip
2020-03-16 05:39:19

Mario Hippmann
2020-03-16 05:40:32

Jim Carswell
2020-03-16 05:44:49

John Yip
2020-03-16 05:47:47

Mario Hippmann
2020-03-16 05:52:07

Jim Nelson
2020-03-16 05:54:51

Mario Hippmann
2020-03-16 07:39:36

Aaron Strome
2020-03-16 08:59:03

Mario Hippmann
2020-03-16 16:52:24

Aaron Strome
2020-03-16 16:55:11

Mario Hippmann
2020-03-16 17:01:25

Aaron Strome
2020-03-16 17:04:33

Aaron Strome
2020-03-16 17:05:12

Mario Hippmann
2020-03-16 17:21:42

Aaron Strome
2020-03-16 17:22:55

Aaron Strome
2020-03-16 17:24:16

Mario Hippmann
2020-03-16 17:28:58

Aaron Strome
2020-03-16 17:30:44

Aaron Strome
2020-03-16 17:31:20

Mario Hippmann
2020-03-16 17:31:51

Aaron Strome
2020-03-16 17:32:50

Aaron Strome
2020-03-16 17:34:03

Mario Hippmann
2020-03-16 17:34:41

Aaron Strome
2020-03-16 17:35:15

Mario Hippmann
2020-03-16 17:35:59

Aaron Strome
2020-03-16 17:37:47

Mario Hippmann
2020-03-16 17:39:26

Aaron Strome
2020-03-16 17:40:30

Aaron Strome
2020-03-16 17:41:11

Aaron Strome
2020-03-16 17:42:21

Mario Hippmann
2020-03-16 17:44:02

Aaron Strome
2020-03-16 17:46:22

Mario Hippmann
2020-03-16 17:46:34

Aaron Strome
2020-03-16 17:47:34

Mario Hippmann
2020-03-16 17:50:15

Aaron Strome
2020-03-16 17:50:58

Aaron Strome
2020-03-16 18:47:45

Mario Hippmann
2020-03-16 18:52:45

Aaron Strome
2020-03-16 18:53:54

Aaron Strome
2020-03-16 18:54:56

Mario Hippmann
2020-03-16 18:55:03

Aaron Strome
2020-03-16 18:56:01

Aaron Strome
2020-03-16 18:57:38

Mario Hippmann
2020-03-16 18:59:07

Aaron Strome
2020-03-16 19:01:36

原文網址 Conan Lloyd
2020-03-16 04:48:27

My Loubie Dragon Chess pawn army is almost complete. Last 2 are printing now and more resin arrives tomorrow. Which pieces should I print next?

翻譯年糕

John Driggers
2020-03-16 05:58:08

Conan Lloyd
2020-03-16 06:00:36

John Driggers
2020-03-16 06:03:48

Conan Lloyd
2020-03-16 06:41:15

原文網址 Nathan Hatfield
2020-03-16 03:40:56

HELP!
TL;DR I'm getting weird rogue artifacts when I try and print small things, but RERF prints work just fine.
Printer: Photon S Resin: Siraya Tech Fast (White) Settings: (Below)
I did a RERF test print (the Ameralabs Town by nipunawg on Thingiverse) and found an exposure that worked well.
Then when I tried to print a small chair (1:96 / 1/8"=1' scale) I get unknown prints along the Y-axis. (photo below)
I ran my file through Photon File Validator, and nothing was off. I included a photo from Chitubox to show my supports.
I thought it might be USB or hardware issues but my RERF prints do just fine. I have tried printing in .photon and .photons and both give the same result.
Any help would be appreciated! 翻譯年糕

原文網址 Natasha Kerensky
2020-03-16 03:23:37

Prototype 3x3 puzzle box I'm Workin on. Up next. Improve design and add details on faces

翻譯年糕

Neil Garrett
2020-03-16 03:28:47

Natasha Kerensky
2020-03-16 03:29:32

William Keller
2020-03-16 03:35:09

Natasha Kerensky
2020-03-16 03:36:20

Mark Haly
2020-03-16 03:37:16

Alexx Butnotalex
2020-03-16 03:53:11

Neil Ramsay
2020-03-16 05:44:50

Ante Ravlić
2020-03-16 17:42:03

Mika Vienonen
2020-03-17 06:02:26

原文網址 Daniel Funposter
2020-03-16 03:16:34

Print bed level new issue:

New issue ive been experiencing, Been printing really well the past few days but now nothing print. I get maybe 1 layer stuck to the bottom of the bed then nothing.

Noticing: print bed does not hit glass anymore when attempting to bed level. I can cant the bed forward or backward with a touch and it wont go down any further. Could this be the issue?

翻譯年糕

Scott Pavlich
2020-03-16 04:58:06

You cannot lower the bed using the touchscreen after it hits the home position?

Miroslav Zajíček
2020-03-16 05:11:00

check sensor behind vat

原文網址 Andrew Kent
2020-03-16 02:42:49

I've been having issues with Resin curing on the supports and underside of the model with the supports, I'm using clear resin. I think I'm either keeping the vat too full, too long exposure on my resin (its clear so uv light will diffuse through the print) or I need to add something to my print set up to keep the resin in the vat warmer

翻譯年糕

Simon Wilson
2020-03-16 04:13:04

Merv Hinton
2020-03-16 05:19:41

原文網址 Ken Schmitt
2020-03-16 00:12:35

my tools have been tossed, i had everything printer related in a box next to the printer, and thats gone now. can someone tell me the tools that come with the photon that i can replace them?

翻譯年糕

Anders Scot Hudson
2020-03-16 00:15:46

Ken Schmitt
2020-03-16 01:40:57

Wes Mischke
2020-03-16 04:22:03

Brian Jones
2020-03-16 04:42:33

Tom Sargison
2020-03-16 05:21:49

Ken Schmitt
2020-03-16 08:45:43

Brian Jones
2020-03-16 08:46:30

Ken Schmitt
2020-03-16 08:46:52

Ken Schmitt
2020-03-16 08:47:21

Ken Schmitt
2020-03-16 08:53:44

Ken Schmitt
2020-03-16 08:53:52

Ken Schmitt
2020-03-16 08:54:31

Ken Schmitt
2020-03-16 08:54:56

Ken Schmitt
2020-03-16 09:00:02

Ken Schmitt
2020-03-16 09:04:07

Ken Schmitt
2020-03-16 09:11:13

全不選發文排行