Anycubic Photon Printer Owners 造訪社團 » youtube

Well.. something is happenig. Test-cube from the Anycubic USB stick (ofcourse on a fresh, new Sandisk USB stick formatted to FAT32), original firmware that came with the printer (v3.4.1). Screen sealed with Kapton tape, then levelled with paper as the manual described, with the videos I've watched on Youtube on my mind. Figured I'd do my first test-run with the stuff the factory sent it with.

Fingers crossed... already had some encouraging popping while the little round base was printing...

翻譯年糕

Need some help again guys having issues.

Talking with anycubic but they are just referring me to the youtube videos they have.

I have check Z wobble and there is none machine is level. Z zero is really good

Print settings are

Layer height 0.03mm
Bottom layers 5 exposure 95sec
Standard exposure 10sec
Off time 3 sec
Lift retract 6mm

I'm having a real issue with the supports having this wobble In it and in turn of it being in my supports it is going through my print since i print on a twin axis angle. Any help would be amazing as I'm almost tempted to ask for a refund.

翻譯年糕

2 weeks of learning to use the photon.
Using a cr10s fdm printer for 2 years.

1. Learn to level.
2. Learn to tune your fep (part of leveling).
3. Acetone cleans uncured resin better than ipa.
4. This one is on going, chitu box is good, but learn how to use the prussia slicer, and validator.
Prussia slicer supports seem better than chitu box. Blue photos are chitu box supports, but the actual print has prussia supports, alot less and a cleaner print.
Helpful guides https://m.youtube.com/playlist…
I hope this helps some people ?

翻譯年糕

Well got up this morning print fail , fep got a small hole, little bit of resin on screen, so my first change, watch YouTube video helped alot.....now to trim and print

翻譯年糕

Has anyone else had problems getting anti-aliasing to work, with an AnyCubic Photon? (not S).

Mine arrived the other day and I was thrilled with the test print. I checked the device and it has firmware 4.2.17 already installed.

I activated anti-aliasing in Chitubox and sliced my mini with anti-alias level eight (pic 1). I checked the file in the file validator and it correctly showed AA level set to eight (pic 2) - so the model definitely sliced with anti-aliasing active.

Yet when I click on the image in the file validator, despite it saying there are eight levels of anti-aliasing, I only ever see green or yellow pixels (pic 3) not the anti-aliased greyscale image the screenshot on github shows (pic 4).

I think the issue is software rather than hardware based, since my hardware came with 4.2.17 already installed on it which is the hardware version recommended in the anycubic youtube video (pic 5). The two-colour display in the file validator just doesn't look right to me! Though maybe it is, I don't know - I tried clicking "convert" and forcing it to recalculate anti-aliasing: it did so, but the preview image is still only green and yellow with no nice gradients as in the app screenshot.

My prints are very much like the "before" photo, not the "after" one: I printed Boba Fett's legs 10 degrees off vertical (with his feet supported on the base plate) so the artifacts are not layer height issues - they look very much like anti-aliasing isn't working....

Any ideas, hivemind?

翻譯年糕

HELP!!! my first prints don't attach on Z-plate. First try (with manual instruction): set Z-axis moving the plate until paper sheet moves not freely. fix the plate with wrench set Z-height as 0 (Tools -> Z=0) PRINT
Second try (following this video https://www.youtube.com/watch?v=j6XHlSyj2ZU ) set Z-axis moving the plate until paper sheet moves not freely. fix the plate with wrench move up the plate and put the vat in its slot move the plate down until the vat moves not freely. set Z-height as 0 (Tools -> Z=0) PRINT
Both prints was paused (3-5%) in order to check if it was attached to the plate, but it was on the bottom of vat. What i'm doing wrong?? ?

救命!!! 我的第一個指紋不附在z板上.
第一次嘗試(手動指示):
設定z軸移動盤子直到紙張不自由移動.
用扳手修理盤子
將z高度設定為0 (工具-> z =0)
印刷

第二次嘗試(關注這個視訊https://www.youtube.com/watch?v=j6XHlSyj2ZU)
設定z軸移動盤子直到紙張不自由移動.
用扳手修理盤子
抬起盤子, 把增值稅放進它的位置
把盤子向下移動, 直到增值稅不自由移動.
將z高度設定為0 (工具-> z =0)
印刷

兩張列印都暫停(3-5 %), 以檢查是否附在盤子上, 但它在增值稅底部.
我做錯了甚麼?? ?

· 查看原文 · 為此翻譯評分

This is the difference between standard auto supports on the left versus 3DPrintingPro’s YouTube tutorial settings for supports and hand placing them on the right.

https://www.youtube.com/playlist…

Siraya Tech Fast Grey.
0.05 layer height
6 bottom layers
Exposure time 8 seconds
Bottom exposure time 60 seconds

Light support top dia .12mm
Light Support top depth .12 mm

Med support top dia .20mm
Med support top depth .30mm

Heavy support top dia .30mm
Heavy support top depth .30mm

翻譯年糕

I have a Photon being shipped now. I need to iron out venting... I can buy a generic flange for the 4" tubing I have, but would rather get one that bolts onto the existing photon unit... I've heard on youtube that there are 2-part vent flanges that can be printed ON the Photon... Does anyone have a link?

Thank you.

翻譯年糕

I need some help with 3d printing ultrasounds. Using slicer.org. Software. I got a bunch of dicom jpg and tiff files from an ultrasound tech. But cannot get them to stack like in YouTube videos. What exactly do I need to ask the tech to do or type of files? Anyone experienced in this?

翻譯年糕

Thanks for the add. I do alot with 1:25 scale models and these printers have really been a game changer for the hobby!! I havent had any major issues yet. (Fingers crossed) heard about this group on a YouTube video last night so i figured it would be a good source to help when i can and be helped when needed.

翻譯年糕