• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » Google

原文網址 Robert Silvers
2019-01-09 11:05:42

Instructions for printing close-tolerance parts:

First step is see where you are at by printing my test-gauge set: https://www.thingiverse.com/thing:3325364

The most precise resins will allow the GO -0.1 pin to pass through the ring but the NOGO +0.1 should not go through. Any resin that can do that needs no further action. See list of resins already tested here:

https://docs.google.com/…/1yDwszgncTyOxvyJho6y1kxLJquH2GsfL…

If your print will only allow the GO -0.2 or GO -0.3 to pass through, then it is printing over-sized and needs corrective-action. I have worked with the developers to get two programs so far to offer this correction.

Method 1 (easy way): Buy Formware https://www.formware.co and set up a printer profile for that resin and put in the correction based on the gauge reading. So if the gauge would only allow GO -0.3 to pass, then use a value of 3 pixels or -0.15mm / -150 microns.

Method 2 (hard, but free): Go to this site and click on Clone or Download: https://github.com/Photonsters/VoxelsOps

Also download Node and install it: https://nodejs.org/en/download/

Select Download Zip and unzip it somewhere. Open a command-line shell and go to the directory that you unzipped it. Type commands 'npm i' then change directory to app, and do 'npm i' again.

Back out of apps, and go into directory helpers. There is a command called erode.js

Run this command with 'node erode -s yourphotonfile.photon -x 1 -y 1 -z 0 -d path-to-emty-dir-to-put-slices-into

Now go here and install PhotonFileEditor by following the instructions on that page:

https://github.com/Photonsters/PhotonFileEditor

Now load your original .photon file into the editor. Then import the slices that VoxelsOps generated. Then save out the photon file again.

That is all.

Future plans: Voxels Ops may get easier to use by writing photon files directly, so that PhotonFileEditor is not needed. And, PhotonOpenSlicer may end up having this horizontal size compensation, in which case it would just be a matter of saving your STl to a folder that PhotonOpenSlicer monitors and it would just automatically generate the photon file for you. Thirdly, ChiTuBox said they would add this feature to a future paid version.

翻譯年糕

Dustin Scott
2019-01-09 11:31:54

Kristian Domingo
2019-01-09 11:43:47

Robert Silvers
2019-01-09 11:52:42

Richard Shapiro
2019-01-10 13:01:42

Nathaniel Silva Nerona
2019-01-10 13:11:08

Robert Silvers
2019-01-10 13:27:29

Ryan Blacklaws
2019-01-12 06:18:28

Robert Silvers
2019-01-12 06:30:14

Ryan Blacklaws
2019-01-12 06:31:33

Robert Silvers
2019-01-12 06:34:35

Ryan Blacklaws
2019-01-12 06:39:09

Elco Jongejans
2019-01-12 16:49:32

Ryan Blacklaws
2019-01-12 19:05:30

Ingo Strohmenger
2019-04-03 17:22:38

Ingo Strohmenger
2019-04-03 17:24:42

Tomas Mitrano P.
2019-07-21 09:35:20

Robert Silvers
2019-07-21 09:36:25


原文網址 Stephen Butt
2019-01-09 07:37:49

Now that i have a printer im getting alot of requests "can u print this, ill pay ya" so question is how do you figure out what to charge to print? Amount of resin used and a hour rate for print time? At a loss, google failed me.lol

翻譯年糕

Richard Shapiro
2019-01-09 07:48:42

Wesley Dowell
2019-01-09 08:17:09

Nathan Prenovost
2019-01-09 08:24:34

Giovanni Lo Verso
2019-01-09 10:18:05

Stephen Butt
2019-01-09 12:16:36

William Hoyt
2019-01-11 20:20:25


原文網址 Tony Boutwell
2019-01-06 07:08:17

For ChiTuBox V1.2.0 - In the PRINT dialogue Is Bottom Light-off Delay the same as Light-off Delay? I didn't see that variable in our docs-google file. Setting it up to print my first sculpture using the anycubic green at .02 layer height.

翻譯年糕

Sean Poeschl
2019-01-06 07:21:45

Tony Boutwell
2019-01-06 07:44:58


原文網址 Joey Smith
2019-01-05 04:12:03

Ok I have googled this and am still confused ...how do I tell if it is an island for support in slicer? Does it show or do I just pick things that are hanging. I have run it through the analyzer als and have had it run fixes ( gets most of them). Am I missing something?

翻譯年糕

Danny Lloyd
2019-01-05 04:14:00

Joey Smith
2019-01-05 04:15:09

Zena Andreou
2019-01-05 04:20:15

Joey Smith
2019-01-05 04:22:26

Joey Smith
2019-01-05 04:35:06

Zena Andreou
2019-01-05 05:46:51

Zena Andreou
2019-01-05 05:47:36

Patrick Nixon
2019-01-05 07:01:26


原文網址 Jacopo Montalenti
2019-01-05 02:40:11

I know I should google it, but you guys are very responsive... what is the nicest looking resin, I don't need mechanical strength I just need it to look good :D
available on amazon prime (price as of Jan-2019)

翻譯年糕

Nick Porterfield
2019-01-05 02:43:57

Jacopo Montalenti
2019-01-05 02:45:21

Nick Williams
2019-01-05 02:48:12

Richard Jacobs
2019-01-05 02:51:55

Mariano Loisi
2019-01-05 03:04:19

Nick Williams
2019-01-05 03:06:27

Nick Williams
2019-01-05 03:06:33

Nick Williams
2019-01-05 03:06:38

Nick Williams
2019-01-05 03:08:43

Nick Williams
2019-01-05 03:09:03

Nick Williams
2019-01-05 03:09:59

David Seaman
2019-01-05 03:10:34

Matt Solomon
2019-01-05 04:05:13

Jacopo Montalenti
2019-01-05 06:44:29

Robert Silvers
2019-01-05 06:55:48

Robert Silvers
2019-01-05 06:56:22

Shawn Atlas
2019-01-06 00:18:50


原文網址 Paul Woodroffe
2019-01-04 05:13:56

Hi everyone.
I always struggle with coloured resin, clear I have nailed.... But i tried white in the past and failed each time and have now bought grey, using the settings from the Google spreadsheet it didn't stick.
So other than sanding the bed, what increases the likelihood of the print sticking on the bed? Is it the length of time for the initial layers?
Thanks

翻譯年糕

Sen Kun
2019-01-04 05:17:26

Paul Woodroffe
2019-01-04 05:27:39

Fred Breton
2019-01-04 05:30:44

Richard Shapiro
2019-01-04 06:19:58


原文網址 Bryan Mikolajewski
2019-01-02 15:39:17

I think the SLA gods approve of the new shelf, but they still do not give full blessing.. Massive info download below, I've been trying to rule out as much as possible:

- I cleaned my plate & vat thoroughly, re-leveled it before I ran this print.
- I'm using Anycubic brand Black resin, which I shook for 5 minutes solid to make sure I had a good mix.
- Followed the Google Doc's recommended program for Anycubic Black - .025 Layer Height, 7.5 Normal Exposure, 3.5 Off Time, 90s Bottom Exposure, 3 Bottom Layers.
- My print room can get pretty cool, so I let my space heater run in there for a bit to warm the room up to mid 60F
- Used Meshmixer's Analysis > Orientation feature on each mini. MM's supports, were first autogenerated, then forced a few additional in parts I thought needed more help. Included a screenshot of my settings.

Worth noting -- the last 2 prints I've run, the bottom of the vat clung to the LCD and wouldn't slide out easy. Enough so that when the vacuum broke, there was a good 'pop' as the seal broke. During printing, I heard nothing out of the ordinary. There was no residue on the LCD when I cleaned (I gently ran a razor over the LCD to check, no snags or residue). Could the FEP need replacing? It's a bit cloudy, and does have a few marks & crease lines in the plastic, particularly with this Anycubic Black, since the supports are much, much harder to knock off with the scraper.

翻譯年糕

Fred Breton
2019-01-02 15:55:45

Fred Breton
2019-01-02 15:55:55

Fred Breton
2019-01-02 15:56:04

Fred Breton
2019-01-02 15:56:12

Fred Breton
2019-01-02 15:56:17

Fred Breton
2019-01-02 15:57:52

Joel Dawson
2019-01-02 23:31:37

Bryan Mikolajewski
2019-01-03 00:18:11

Alex Varley
2019-01-03 00:37:20

Alex Varley
2019-01-03 00:38:02


原文網址 Rafael Anthony Acevedo
2019-01-01 15:22:11

Just picked up some Nova3D blue resin. Does anyone have some good settings? Checked the Google doc and it's not listed. Thanks!

翻譯年糕


原文網址 Patrick Smith
2019-01-01 03:47:52

First non-test print didn't stick to the bed.. I re-leveled and re-adjusted z height.

Second print stuck to the bed very well, but broke off 1/3 of the way through. It looks like it broke off at the supports. I used Chitubox for slicing. Below are my settings. I used small supports because I read that was good in several posts.

The supports have the consistency of yarn and are very small.

so do you think I should increase the exposure, or change to medium supports?

I got my settings from here.. which is supposed to be a good resource. I am using the anycubic green resin that comes with it for now.

https://docs.google.com/…/1crvzMnt_8NJXAsABinoIhcOjE8…/edit…

翻譯年糕

Marco Palencia
2019-01-01 03:55:21

Patrick Smith
2019-01-01 04:02:57

Marco Palencia
2019-01-01 04:03:47

Richard Shapiro
2019-01-01 05:01:58

Patrick Smith
2019-01-01 05:22:40

Richard Shapiro
2019-01-01 05:27:40

Richard Shapiro
2019-01-01 05:28:37

Patrick Smith
2019-01-01 05:30:26

Wesley Dowell
2019-01-04 01:34:40


原文網址 Robert Silvers
2019-01-01 00:55:18

Check out this gauge set to test your resin:

https://www.thingiverse.com/thing:3325364

Please do this survey so that we can get data to show that a "horizontal size compensation" feature needs to be included in the free slicer software. Also, it will help us decide what resin to try next based on other people's objective results.

Results:

https://docs.google.com/…/1yDwszgncTyOxvyJho6y1kxLJquH2GsfL…

翻譯年糕

Tony Boutwell
2019-01-01 00:56:33

Ingo Strohmenger
2019-01-01 01:05:40

Che Fielding
2019-01-01 01:10:15

Robert Silvers
2019-01-01 01:11:59

Sen Kun
2019-01-01 01:14:31

Fred Breton
2019-01-01 01:14:35

Vinicius Silva
2019-01-01 01:18:59

Mantas Aus
2019-01-01 01:30:33

Robert Silvers
2019-01-01 01:31:20

Jeff Schaefer
2019-01-01 01:57:00

Doug Johnson
2019-01-01 02:31:17

Robert Silvers
2019-01-01 02:40:46

Vinicius Silva
2019-01-01 05:07:28

Robert Silvers
2019-01-01 05:08:25

Vinicius Silva
2019-01-01 05:09:08

Robert Silvers
2019-01-01 05:09:41

Vinicius Silva
2019-01-01 05:13:11

Vinicius Silva
2019-01-01 05:16:29

Robert Silvers
2019-01-01 05:20:40

Vinicius Silva
2019-01-01 05:53:47

Sam Cunningham
2019-01-02 05:59:33

Robert Silvers
2019-01-02 10:05:34

Robert Silvers
2019-01-02 15:04:57

Sen Kun
2019-01-02 16:04:47

Sen Kun
2019-01-02 16:09:38

Vinicius Silva
2019-01-02 17:59:57

Robert Silvers
2019-01-02 19:41:05

Robert Silvers
2019-01-02 19:46:19

Sen Kun
2019-01-02 20:01:09

Robert Silvers
2019-01-02 20:11:02

Sen Kun
2019-01-02 20:23:50

Robert Silvers
2019-01-02 20:24:57

Sen Kun
2019-01-02 20:35:34

Robert Silvers
2019-01-02 20:38:05

Sen Kun
2019-01-02 20:43:24

Robert Silvers
2019-01-02 20:46:17

Robert Silvers
2019-01-02 20:50:11

Sen Kun
2019-01-02 21:03:14

Robert Silvers
2019-01-02 21:08:05

Ivan Antharon Antalec
2019-01-02 21:09:20

Vinicius Silva
2019-01-02 21:12:00

Sen Kun
2019-01-02 21:12:30

Sen Kun
2019-01-02 21:14:22

Vinicius Silva
2019-01-02 21:17:50

Vinicius Silva
2019-01-02 21:23:07

Ivan Antharon Antalec
2019-01-02 21:25:19

Sen Kun
2019-01-02 21:30:23

Vinicius Silva
2019-01-02 21:34:39

Robert Silvers
2019-01-02 21:42:35

Vinicius Silva
2019-01-02 21:46:55

Robert Silvers
2019-01-02 21:48:42

Vinicius Silva
2019-01-02 21:53:32

Robert Silvers
2019-01-02 22:06:14

Robert Silvers
2019-01-02 23:03:39

Robert Silvers
2019-01-04 13:00:41

Robert Silvers
2019-01-05 21:07:49

Robert Silvers
2019-01-06 04:42:00

Robert Silvers
2019-01-06 12:59:11

Dustin Scott
2019-01-10 09:40:22

Robert Silvers
2019-01-10 09:45:08

Dustin Scott
2019-01-10 10:18:01

Ivan Antharon Antalec
2019-01-10 14:31:42

Keith Hebard
2019-02-21 03:08:59

Robert Silvers
2019-02-21 03:14:22

Robert Silvers
2019-02-21 03:14:40

Keith Hebard
2019-02-21 03:16:35

Ivan Antharon Antalec
2019-02-21 03:16:39

Keith Hebard
2019-02-21 03:18:23

Keith Hebard
2019-02-21 03:18:49

Keith Hebard
2019-02-21 03:19:11

Keith Hebard
2019-02-21 03:21:38

Ivan Antharon Antalec
2019-02-21 03:25:48

Keith Hebard
2019-02-21 03:33:23

Robert Silvers
2019-02-21 03:37:18

Keith Hebard
2019-02-21 03:39:55

Artur Kawa
2019-06-04 01:54:20

Artur Kawa
2019-06-04 01:54:52

Ivan Antharon Antalec
2019-06-04 01:55:38

Ivan Antharon Antalec
2019-06-04 01:55:53

Artur Kawa
2019-06-04 01:56:36

Artur Kawa
2019-06-04 04:34:42

Nard Janssens
2019-06-05 00:21:58

Artur Kawa
2019-06-05 00:22:52

Artur Kawa
2019-06-05 11:55:09

Peter Kings
2019-06-05 12:03:25

Dan Mech
2019-10-19 09:20:34

Vinicius Silva
2019-10-19 19:46:18

Dan Mech
2019-10-19 19:54:34

Vinicius Silva
2019-10-20 10:49:50

Vinicius Silva
2019-10-20 10:49:55


 

全不選 發文排行