• 3D列印服務
  • #maker+t=market
  • COSPLAY 3D 建模
  • 1
  • 2
  • 3

Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Rafael Anthony Acevedo
2019-03-03 07:03:44

Hey all - printing a ring. It's just a green lantern ring for a friend, but I am unsure of the best orientation for supports. Thoughts?

翻譯年糕

Dustin Skye
2019-03-03 07:47:21

Brandon Kennedy
2019-03-03 08:11:15

Dustin Skye
2019-03-03 08:12:41

Brandon Kennedy
2019-03-03 08:13:35


原文網址 Rafael Anthony Acevedo
2019-01-20 00:41:58

Ok folks - looking for some more help. Still trying to print this damn figure. Gone through . 5l of resin with almost nothing to show for it. I am sure it's operator error and there is a learning curve, but it would be nice to get some good prints. Without supports - fine. With supports - not so much.

Still figuring out orientation and supports. In the pics below, the top looks great, but the part surrounded by the supports looks like hamburger. Also, notice the small layer at the back. I almost thought that was plastic and that I had not reovee the protective film from the FEP, but it's not. FEP looks great and it was indeed resin. Not sure why it would have done that.

Thoughts on what to try next?

翻譯年糕

Pijvs Magnifiqvs
2019-01-20 00:47:24

Rafael Anthony Acevedo
2019-01-20 00:48:08

Carla Birch
2019-01-20 00:50:58

Kyle Van Patten
2019-01-20 00:58:39

Rafael Anthony Acevedo
2019-01-20 01:00:26

Rafael Anthony Acevedo
2019-01-20 01:01:05

Carla Birch
2019-01-20 01:07:32

Daniel Ignacio Perez
2019-01-20 01:09:05

Carla Birch
2019-01-20 01:09:23

Carla Birch
2019-01-20 01:10:45

Bernie Horowitz
2019-01-20 01:18:59

Rafael Anthony Acevedo
2019-01-20 01:30:51

Anthony Pham
2019-01-20 05:04:23

Seona van der Pol
2019-01-20 05:20:27

Seona van der Pol
2019-01-20 05:27:35

Seona van der Pol
2019-01-20 05:29:25

Rafael Anthony Acevedo
2019-01-20 05:53:57

Mark Wardle
2019-01-20 07:21:40

Rafael Anthony Acevedo
2019-01-20 07:43:14

Marshall Tearle
2019-01-20 08:58:31

Wesley Dowell
2019-01-21 01:10:38

Rafael Anthony Acevedo
2019-01-21 01:51:53


原文網址 Rafael Anthony Acevedo
2019-01-16 09:17:40

Ok. Getting really stumped. Trying to print the same piece over a half dozen times. Still no luck. What I don't understand now is that it printed pretty nicely the form. But the details are missing on the bottom. I thought about exposure adjustments, but why would one side have well defined details and one side not? Pics below. You notice you can see the texturing on the side opposite the supports, but on the side with supports, not so much.

翻譯年糕

Walter Behrens
2019-01-16 21:02:00

Sen Kun
2019-01-16 21:37:28

Rafael Anthony Acevedo
2019-01-16 22:10:03

Sen Kun
2019-01-16 22:26:53

Rafael Anthony Acevedo
2019-01-16 22:29:37

Sen Kun
2019-01-16 22:30:58


原文網址 Rafael Anthony Acevedo
2019-01-15 13:04:28

Hey all - noticed a weird pattern between my vat and the LCD. Pics below. Initially thought I must have installed the new FEP wrong and maybe I had a leak. I stopped the print and removed the vat and used a white cloth to while both the underside of the vat/FEP as well as the LCD. Nothing there. Could this be temp related, is it normal? Seems to be printing ok, I restarted the print. We'll see. Just wondering if others had seen that before.

翻譯年糕

Ben Coe
2019-01-15 13:09:43

Reb O'Rourke
2019-01-15 13:20:08

Rafael Anthony Acevedo
2019-01-15 13:28:09

Rafael Anthony Acevedo
2019-01-15 13:28:39

Reb O'Rourke
2019-01-15 13:37:19

Will Oliver
2019-01-15 14:06:10

Will Oliver
2019-01-15 14:07:16

Will Oliver
2019-01-15 14:08:05

Rafael Anthony Acevedo
2019-01-15 14:09:26

Will Oliver
2019-01-15 14:10:38

Rafael Anthony Acevedo
2019-01-15 14:11:30

Rafael Anthony Acevedo
2019-01-15 15:27:45

Rafael Anthony Acevedo
2019-01-15 15:28:37

Jeremy Hartman
2019-01-15 16:41:14

Sen Kun
2019-01-15 17:02:45

Will Oliver
2019-01-15 21:37:30

Rafael Anthony Acevedo
2019-01-15 22:30:15

Rafael Anthony Acevedo
2019-01-15 22:31:32

Dylan Trinh
2019-01-16 04:33:24

Peter Ede
2019-01-16 10:34:59

Dani Corado Quirós
2019-01-17 17:42:17


原文網址 Rafael Anthony Acevedo
2019-01-14 22:23:02

Ok guys. Still not having any luck getting this figure to print. Printed it elbow down as recommended. Used support settings recommended here. Top of the model seems fine. Great detail and comes out beautifully. However, where the elbow starts and underneath of the arm don't have a lot of detail and the elbow is a mess instead of nice and round as it should be. Any thoughts? I'm learning so I expect a curve, just looking for some thoughts. Also - this is on a brand new FEP so that shouldn't be the issue.

Thanks.

翻譯年糕

Savio Ku
2019-01-14 22:38:34

Richard Shapiro
2019-01-14 23:14:42

Rafael Anthony Acevedo
2019-01-14 23:20:38

Savio Ku
2019-01-14 23:48:23

Rafael Anthony Acevedo
2019-01-15 00:37:16

Savio Ku
2019-01-15 00:55:50

Alisson Gois
2019-01-15 07:04:46

Alisson Gois
2019-01-15 07:04:59

Rafael Anthony Acevedo
2019-01-15 09:06:23

Alisson Gois
2019-01-15 23:51:25


原文網址 Rafael Anthony Acevedo
2019-01-07 07:07:22

Getting ready to replace the FEP for the first time. I've watched the video and looks straight forward. I do have a couple of questions - the FEP I am using is the replacement one included with the printer. Is there any film I need to removed from the sheet? I had heard that some have a protective film. Secondly, How important is it to get the 13mm gap correctly? They use a drink cap that they say is 13mm, but I can't find one that is 13mm lol. Is close enough good enough?

翻譯年糕

Chad Elstad
2019-01-07 07:10:37

Richard Shapiro
2019-01-07 07:12:35

Rafael Anthony Acevedo
2019-01-07 07:18:23

Jeremy Lauzon
2019-01-07 08:26:57

Rafael Anthony Acevedo
2019-01-07 08:29:12

Rafael Anthony Acevedo
2019-01-07 08:46:28

Richard Shapiro
2019-01-07 08:47:16

Rafael Anthony Acevedo
2019-01-07 08:47:41

Rafael Anthony Acevedo
2019-01-07 08:49:00

Richard Shapiro
2019-01-07 08:53:12

Rafael Anthony Acevedo
2019-01-07 09:08:57

Mike Johnson
2019-01-07 10:37:08

Craig Burrows
2019-01-07 13:15:53

Andris Drulle
2019-01-07 22:49:18


原文網址 Rafael Anthony Acevedo
2019-01-07 00:58:46

Hey folks. Need some help. Looks like My FEP had a small hole in it because there was resin underneath after this last print finished. I wiped up the loose resin, but a dime to nickel size piece has cured/hardened on the LCD. Is it shot, or is there a way to remove it? I tried rubbing with some alcohol and that actually did make it smaller, but it's still there. Thoughts? Thanks for any help.

翻譯年糕

Derek Reihe
2019-01-07 00:59:37

Rafael Anthony Acevedo
2019-01-07 01:02:26

Derek Reihe
2019-01-07 01:04:10

Rafael Anthony Acevedo
2019-01-07 01:19:23

Che Fielding
2019-01-07 01:29:15


原文網址 Rafael Anthony Acevedo
2019-01-06 01:02:15

Ok, so I'm learning a lot, unfortunately at the expense of this bottle of resin... And a lot of time. A few questions. I am trying to print out the black panther model in pieces, split, and keyed. I'm having a few issues I was hoping someone can help me with.

1 - supports are making pretty big marks on the item. I'm trying not to paint this one so that's a big issue. What can I do to avoid that? Which settings should I change and to what? I think it's tip size and depth.

2 - even with multiple different orientations, it's as if I'm losing a lot of detail just above the supports where the model starts. In other words I printed the arm elbow down as recommended here and there are no real details visible on the skin like there should be.

I also realized that I can't print something with a key socket Downwards. It becomes a mess.

Thoughts. Some pics below.

翻譯年糕

Rafael Anthony Acevedo
2019-01-06 01:21:46

Eileen Bowen
2019-01-06 01:24:05

Rafael Anthony Acevedo
2019-01-06 01:26:35

Rob Mayberry
2019-01-06 06:16:40

Rafael Anthony Acevedo
2019-01-06 06:42:35

Seona van der Pol
2019-01-06 07:36:10

Rafael Anthony Acevedo
2019-01-06 08:41:03

Rafael Anthony Acevedo
2019-01-06 08:41:13


原文網址 Rafael Anthony Acevedo
2019-01-04 11:31:08

Ok - can't seem to get any prints with this Nova 3d resin. I'm sure it's settings. I used 12 sec Exposure and 80 sec bottom layer. With 9 bottom layers.

Here's the result. Supports seem to print but the rest of the model didn't. It was stuck to the bottom of the FEP. Don't think this is a leveling issue because the raft printed fine. Any thoughts? Should i try a higher or lower exposure.?

翻譯年糕

Fred Breton
2019-01-04 11:37:41

Rafael Anthony Acevedo
2019-01-04 11:39:27

Fred Breton
2019-01-04 11:40:02

Fred Breton
2019-01-04 11:40:32

Rafael Anthony Acevedo
2019-01-04 11:40:49

Fred Breton
2019-01-04 11:41:04

Rafael Anthony Acevedo
2019-01-04 11:41:14

Rafael Anthony Acevedo
2019-01-04 11:41:28

Fred Breton
2019-01-04 11:41:36

Fred Breton
2019-01-04 11:41:53

Fred Breton
2019-01-04 11:42:02

Fred Breton
2019-01-04 11:42:16

Fred Breton
2019-01-04 11:43:08

Rafael Anthony Acevedo
2019-01-04 11:45:28

Fred Breton
2019-01-04 11:46:43

Rafael Anthony Acevedo
2019-01-04 11:47:31

Fred Breton
2019-01-04 11:47:36

Fred Breton
2019-01-04 11:47:57

Rafael Anthony Acevedo
2019-01-04 11:48:01

Fred Breton
2019-01-04 11:48:13

Rafael Anthony Acevedo
2019-01-04 11:48:29

Rafael Anthony Acevedo
2019-01-04 11:49:01

Fred Breton
2019-01-04 11:49:36

Rafael Anthony Acevedo
2019-01-04 11:50:02

Rafael Anthony Acevedo
2019-01-04 11:50:20

Fred Breton
2019-01-04 11:50:42

Fred Breton
2019-01-04 11:50:57

Rafael Anthony Acevedo
2019-01-04 11:51:03

Fred Breton
2019-01-04 11:51:45

Rafael Anthony Acevedo
2019-01-04 11:52:16

Rafael Anthony Acevedo
2019-01-04 11:52:41

Fred Breton
2019-01-04 11:52:43

Fred Breton
2019-01-04 11:54:32

Rafael Anthony Acevedo
2019-01-04 11:55:01

Jay Kay
2019-01-04 11:56:04

Rafael Anthony Acevedo
2019-01-04 11:56:18

Rafael Anthony Acevedo
2019-01-04 11:56:30

Fred Breton
2019-01-04 11:57:40

James Cachia-Garrett
2019-01-04 15:43:33

James Cachia-Garrett
2019-01-04 15:44:55

Rafael Anthony Acevedo
2019-01-05 00:19:46


原文網址 Rafael Anthony Acevedo
2019-01-04 08:47:13

Ok all - printing this Black Panther model and would like some input on orientation. Still a newb with this printer! Thanks!

翻譯年糕

Dustin Scott
2019-01-04 08:57:50

Rafael Anthony Acevedo
2019-01-04 09:01:39

Rafael Anthony Acevedo
2019-01-04 09:02:57

Rafael Anthony Acevedo
2019-01-04 09:34:16

James Cachia-Garrett
2019-01-04 10:41:29

Rafael Anthony Acevedo
2019-01-04 10:42:06

James Cachia-Garrett
2019-01-04 10:45:36

Rafael Anthony Acevedo
2019-01-04 10:50:40

James Cachia-Garrett
2019-01-04 10:55:01

Rafael Anthony Acevedo
2019-01-04 11:02:02


 

討論主題

全不選 常用關鍵字