Anycubic Photon Printer Owners 造訪社團 » TIP

I understand this is going to get multiple answers, but Im looking to jump from FML to resin printing. I have cr10 ender 3, ender3 pro, cr10s. Im looking for the resin printer with the least amout of hassle. I have added an ABL to each FLM printer and with very little maintance, tighting bolts every 2-3 months, washing the hairspray from the bed every 2-3 weeks, so i want a low maintance option for resin printing. Ive seared past posts on this forum and watched videos and read other sites, im not being lazy w/ the ? just want experienced feedback.

what is the best resin printer that will balance print quality, ease of maintainence, etc. is the photon really the way to go, many are suggesting the xpax x1 saying you do not have to even level the bed. i dont mind spending 750$ ish. can you guys help

翻譯年糕

Anyone have experience printing at .01? Any tips?

翻譯年糕

Voodoo sorcerer, thank you Susan Sioux Mercer for pointing to that amazing model, sliced in chitubox 1.4, layer height .03 / 7.5s, resin phrozen grey, AA x 2

I only removed supports with a flush cutter, not even sanded, nor UV cured. My personal tip, put your model in hot water after IPA, supports become very soft and are removed very easily

Curtain supports is a thing ? ?

翻譯年糕

I’m currently using a mega i3 but am keen to try a resin printer
My question: is it realistic to expect to be able to use it for bigger prints (obviously multiple small prints assembled)
Thanks

翻譯年糕

Get it while stocks last. Tipping is totally appreciated. Enjoy the model! :D

翻譯年糕

Need some advice please:

Photon S - My second print came out pretty darned good, but it seemed to have a lot of little pock marks and lost a bit of detail towards the highest tip of the Z axis. Also there was quite a bit of that slime/jelly stuff in the resin vat afterwards. I heard the clacking of the model pulling away from the FEP film for the first 1/2 - 2/3 of the print, but nothing afterwards. The film also has indents on it from where the model began its support structures. Any tips to improve all this? Any of it just normal par for the course and expected wear and tear? It was printed at 0.05 with 10s exposure time and 8 bottom layers with 60s exposure. I used the auto support structure, but I think I'll start making my own because they came out a little more clumped and fully adhered to the print than the sliced file suggested.

Thanks all for the help, this is the best little printer.

翻譯年糕

Alright, so why in Chitubox can I not move supports OFF of the figure? In photon slicer, you can easily. I want supports to be anchored to the plate, not other spots on the model. Anyone have any tips? I have videos of me doing/trying in both slicers.

翻譯年糕

Hi guys I'm looking at ordering one of these printers. I currently have 5 FDM printers and looking to add a Sla to the mix. What are your opinions on them or top tips?

翻譯年糕

Any tips on making sure the prints are cured properly. They still smell like resin.

翻譯年糕

❗️ ? ??‍♀️ HELP WANTED PLEASE ??‍♀️ ? ❗️

☺️ BIG THANX IN ADVANCE ☺️

Here in The Netherlands ?? is now a heat wave ( 40 degrees Celsius ) ? .

? Is it possible that Resin becomes fluid again????

I made a while back my prints hollow and did not know about the drainage hole so the prints even after hardening bursted open weeks later...
After many tips from you lovely peeps I made with a little drill holes to let the resin out,cleaned it with isopropyl and washed it out with water, let it dry again and now after a few weeks it still bursts open?!?! ?

? OMG ? What’s going on????

? Is it possible that Resin becomes fluid again????
Ps, all my new designs are NOT hollow and made a little hole at the bottom because than I can put them on a stick when I paint them...

翻譯年糕