Anycubic Photon Printer Owners 造訪社團 » g code

so my printer has consistently failed lately by either rebooting mid-print (usually in first 2 or so layers), giving M_11820 error, or zaxis failing to move after initiating print and printing all layers without moving.

i replaced the power supply with a new 12v 8A brick and verified polarity and voltage before trying it out - same issue as before - not fixed

i updated firmware - not fixed

i reset eeprom with default code - not fixed and now zaxis will not move at all no matter what.

i tested mainboard reference voltage and it showed 5.89v


so i've had a printer that failed about 14 of the last 15 prints but now i have a printer that will not move the zaxis motor with any of the ui commands or prints.


is any firmware gcode space-magic going to solve my problem or am i waiting to go through the troubleshooting process with anycubic and headed for a new mainboard or z motor ?



please help. - also i'm currently on 4.2.18 firmware on a standard model photon 翻譯年糕

Anyone know of a visualizer for SLA prints like gcode.ws for FDM prints? 翻譯年糕

Strange problem: Every time I press HOME the build plate goes up a little (about 10 mm) and it beeps. Never goes down. Resetting Z0 doesn't change anything. I even tried a reset with factory-defaults.gcode, it doesn't change ... ?

翻譯年糕

I am trying to run the exposure calibration test from photonsters, but when I put the files onto the USB, the test-mode.gcode doesn't show up on the printer. The print-mode one does. Running FW 4.2.19. Anyone have any hints to point me in the right direction please?

翻譯年糕

So I updated my firmware today to 4.2.18 and used gcode

M8030 T0
M8500

to turn off the fan that I had already removed. Now the remaining fan is much louder than before. Should I be concerned?

翻譯年糕

I attempted to print a file on my photon. 1.5 hours later, the print finished but I noticed the Z motor never moved. Now, I cannot move it with up and down arrows. I powered it on and off. Unplugged and replugged. Did a firmware update and an eeprom reset but none of these worked. Prior to this print, I did an exposure finder test where I had to click on test mode.gcode, but I later clicked on the print mode. to revert back to the peeling action. Any possible solutions or suggestions to fix this issue?

翻譯年糕

Is it a bad thing when the preview of your print is just a blank white screen? I tried to start it and it never showed anything on the layer preview when printing so I stopped it. Is this just a problem with my gcode or is my printer not reading thing correctly?

翻譯年糕

Has anyone tried to run the git hub resin calibrator on the Photon S? For some reason the G code is not showing up on the menu

翻譯年糕

I would be grateful for some help please. I am unsure how to disable the deck filter fan in my Photon Classic using GCode. I think, from what I have read here, that I should use M8030 T0 followed by M8500 , but how, like this?
Select this as a file to 'print' from a USB stick? Filename: Fanoff.nc (Photon Classic Turn Deck filter fan off) M8030 T0 M8500 (Saves configuration)
Two things I am unclear about though.... The configuration code from Photonsters says T-0 not T0 The photonsters code lists M8030 for the LED fan and Motherboard fan,(which I suppose is the one I think of as the deck filter fan) so it seems this short code is ambigious?
Photonsters code is here... https://github.com/altLab/photon-resin-calibration/blob/master/resin-xp-finder/print-mode.gcode
Thanks for your help 翻譯年糕

Went to do the exposure test last night for the Elegoo Gray I've been using because the spreadsheet settings weren't giving decent quality. Watched the YouTube video and followed the directions in the zip file. After I ran the test mode gcode I went to run the exposure test, but when I started the exposure test my buildplate wouldn't lower into the vat. Ran the print mode gcode and buildplate lowered properly but the exposure test didn't work. Any idea what I did wrong after running the test mode gcode?

翻譯年糕