Anycubic Photon Printer Owners 造訪社團 » Volt

原文網址 Stephen Lewis
2019-04-15 23:34:04

*Update*
After some suggestions, I checked all internal cables and everything was fine. However, the front touchscreen has been flickering and dimming even going completely white for several months now. never really affected the printer until now. I believe the touchscreen may have died. Thanks everyone! I have contacted Anycubic support.

Question:
I haven't powered on my Photon in a while and when I turned it on in order to run a print, it doesn't seem to boot up. I see the z-axis limit switch light come on and hear/see the fan running but the front screen never kicks on and it makes no other signs of life.

I have done the following
1) unplugged the PSU from the machine.
2) unplugged the power from the PSU
3) tested PSU voltage(12.33v)
4) plugged into a different plug.

I don't think I have a different PSU to test with but all signs seem to point to it being fine.

Any other suggestions?

Thanks!

翻譯年糕

Richard Shapiro
2019-04-15 23:47:27

David Nicholls
2019-04-15 23:50:40

Dave Smith
2019-04-16 00:17:44

Sen Kun
2019-04-16 01:12:57

Sen Kun
2019-04-16 01:14:58

Stefan Giudici
2019-04-16 01:30:04

Carsten Degenhardt
2019-04-16 01:44:57

Stephen Lewis
2019-04-16 04:52:10

Stephen Lewis
2019-04-16 04:53:50

Stephen Lewis
2019-04-16 20:56:39

原文網址 Alex Medeiros
2019-04-13 20:10:25

So I've got my first problem.

There are wierd layer lines that I cannot find any explanation for. I've been printing for about a liter perfectly. Mostly small minis but one or two medium size prints. All with no problems.

These are the largest prints I've done, the wing is the entire height of the print volume! But as you can see the base of the dragon, in the crystals, there are wierd layer artifacts.

I didn't know what the could be causing the layer issues so I though I'd print the wing go see if it would repeat the issue.

The wing is really odd, it has 4 or 5 "layer shifts" like the print head moved a bit. But it's a resin printer without a print head.

I wonder if hollowing the prints could have done something. I used a wall thickness of 1.2.
Normal layer height. One model was hollowed in Meshmixer, the dragon base. And I added a large cutout on the bottom to add supports for the crystal base.
The wing was hollowed in ChiTu box.

So far I've gotten a few suggestions which all could be contributing but nothing real definitive.

1. Bad power supply? The lifting seems to suck to the print bed so maybe it draws to much power. Don't know if this makes sense but a Reddit user said he fixed something similar with a voltage regulator. Anyone else?
2. Wobbly table? It's on a descent folding table but not the most sturdy. I don't know how this could affect the print quality.
3. Z screw binding? Maybe it just for stuck a few times. I would think this would cause other issues like the piece crashing into the build plate or something.
4. Temperature? I print in a small room. The first print, the dragon base, had a computer on and close the door so it could have gotten warm. Not the case with the wing, it printed overnight.
5. Z wobble. Pretty much ruled out as it isn't a consistent problem. At some point I might try to readjust the escentric nut but it's currently working so I'd rather not.

Thinks that about sums up where I'm at. Any tips or if someone has had a similar problem I'd love to know what you did.

Thanks for any suggestions! Really lost here.

翻譯年糕

Silas Bo Nielsen
2019-04-13 20:27:58

Danny Lloyd
2019-04-13 20:58:19

Blake Moody
2019-04-14 05:23:22

Alex Medeiros
2019-04-14 12:53:00

原文網址 Seum Jeong
2019-04-07 18:18:35

I just finished the heater!

Originally I was thinking of making a 'Photonsters PTC Heater Unit', but it was a bit tricky to get parts from where I live, so instead I disassemble a $16.15 small heater to get the parts I needed.

The circuit of this mini heater is very useful because it has functions such as timer, fan speed control, temperature control function, and voltage conversion.

The case was printed with PETG, and the bent part was not melted by the heat of the heater but because of the failure of the middle of printing.

Compared with 'Photonsters PTC Heater Unit', it is slightly bigger.

翻譯年糕

原文網址 Nathaniel Silva Nerona
2019-04-05 22:05:51

Is the Photon power supply autovolt and will work with 220-240v. Asking because bringing a Photon for my brother in the Philippines. TIA

翻譯年糕

原文網址 James Anderton
2019-02-04 02:49:00

Hi all, just wanted some help, I need to replace the power supply for my photon as the cats chewed through the cable! I know from the specs of it I need a 12v 5a 40w power supply. I can see plenty of ones of amazon that are the same 12v 5a but are 60w output.

I realise that the voltage and amps are the same but would the wattage cause issues ?

Cheers Jim

翻譯年糕

Robert Silvers
2019-02-04 03:03:50

Robert Silvers
2019-02-04 03:04:04

Sen Kun
2019-02-04 03:21:56

James Anderton
2019-02-04 04:20:09

Sen Kun
2019-02-04 04:30:05

Robert Silvers
2019-02-04 05:01:44

Richard Russell
2019-02-04 14:49:51

原文網址 Robert Silvers
2019-02-01 22:00:04

I want to find an hour meter and connect it to LED power. How many volts drive the LED?

翻譯年糕

Derick Duffner
2019-02-01 22:11:53

Robert Silvers
2019-02-01 22:12:19

Daniel Warchol-Anderson
2019-02-01 22:14:43

Robert Silvers
2019-02-01 22:16:00

Robert Silvers
2019-02-01 22:23:42

Derick Duffner
2019-02-01 22:27:11

Robert Silvers
2019-02-01 22:42:05

Derick Duffner
2019-02-01 22:46:24

Robert Silvers
2019-02-01 23:49:38

John Boyington
2019-02-02 00:30:00

Matt Mason
2019-02-02 00:34:35

Gazsó Péter
2019-02-02 19:56:07

Robert Silvers
2019-02-03 12:15:54

原文網址 Martin Da Costa
2019-01-09 20:21:05

Temperature is a recurring theme on these pages. When I got my second machine towards the end of last year, I decided to do a side by side comparison. My first machine had already been modified to incorporate temperature control in the print area (more later). I printed the same file on the two printers side by side at the same time. Room ambient temperature was 15C and in my modified machine the print area was at 27C. The print from the temperature controlled machine was definitely crisper and so I modified number 2.

On the top of each printer is a digital temperature controller with a sensor that can be seen to the right of the z slide in the picture. This controls a constant temperature PTC electric fan heater (12V 150W) that is stuck to the floor of the print chamber to the left of the z slide. The fan is always on to circulate the air and blows onto the back of the printer. A separate 12V 20A PSU drives the heating system for both machines. The extraction fan is disconnected so as not to suck out the warm air and the fumes that some find bothersome. I have the upper temperature set for 27C with 1C range. Delay typically takes the temperature down to 25.9C before rising to an overshoot of about 27.8C. This is air temperature and so the thermal mass of the VAT and resin smooths this out to probably just under 27C. The result is total consistency of prints and no discernable difference between the machines. All parts came from Amazon. From KKmoon 200-240V Digital temperature Controller thermocouple -40C to 120C with Sensor. With hind sight, I should have got the 12V model. From Kggy-eu Constant Temperature PTC Electric Fan Heater for Car Small Space Heating Incubator (12V 150W). Remove a mounting lug from this to allow it to be stuck to the base plate.. From LEDSONE LED Power Supply Unit 240Watts 12V 20A Constant Voltage DC. This is good for driving two heating systems.

翻譯年糕

Ben Tseng
2019-01-09 20:36:52

Martin Da Costa
2019-01-09 20:40:05

Thierry Vergé
2019-01-09 20:45:25

Alessio Petricciuolo
2019-01-09 21:54:41

陳彦廷
2019-01-10 00:34:12

Vinicius Silva
2019-01-10 00:42:26

Martin Da Costa
2019-01-10 01:13:17

Vinicius Silva
2019-01-10 01:17:05

Vinicius Silva
2019-01-10 01:18:26

Martin Da Costa
2019-01-10 01:30:21

Robert Silvers
2019-01-10 01:42:37

Vinicius Silva
2019-01-10 01:50:03

César Fernández
2019-01-10 16:46:40

Sen Kun
2019-01-10 17:40:03

Vinicius Silva
2019-01-10 18:34:34

Sen Kun
2019-01-10 18:38:00

Robert Silvers
2019-01-10 18:54:37

Martin Da Costa
2019-01-10 19:23:55

Vinicius Silva
2019-01-10 19:58:41

Martin Da Costa
2019-01-10 20:10:14

Holden8702
2019-01-10 20:41:52

Holden8702
2019-01-10 20:47:31

Vinicius Silva
2019-01-12 05:51:05

Calvin Hobbes
2019-01-16 09:00:29

Vinicius Silva
2019-01-16 10:18:29

Martin Da Costa
2019-01-16 17:59:29

Martin Da Costa
2019-01-16 18:04:34

Vinicius Silva
2019-01-16 18:52:26

Martin Da Costa
2019-01-16 19:47:38

Robert Silvers
2019-01-16 20:49:34

Vinicius Silva
2019-01-16 21:19:09

Vinicius Silva
2019-01-17 04:39:30

Richard Shapiro
2019-01-17 05:05:51

Robert Silvers
2019-01-17 05:10:11

Richard Shapiro
2019-01-17 05:26:42

Calvin Hobbes
2019-01-17 08:03:33

Calvin Hobbes
2019-01-17 08:13:42

Vinicius Silva
2019-01-17 08:14:22

Calvin Hobbes
2019-01-17 08:15:34

Vinicius Silva
2019-01-17 08:17:27

Calvin Hobbes
2019-01-17 08:18:53

Vinicius Silva
2019-01-17 08:21:54

Calvin Hobbes
2019-01-17 20:02:54

Vinicius Silva
2019-01-17 21:48:09

Martin Da Costa
2019-01-17 22:49:05

Martin Da Costa
2019-01-17 22:51:57

Richard Shapiro
2019-01-17 22:53:00

Martin Da Costa
2019-01-17 22:55:30

Richard Shapiro
2019-01-17 22:55:58

Martin Da Costa
2019-01-17 23:04:34

Richard Shapiro
2019-01-17 23:09:08

Richard Shapiro
2019-01-17 23:11:59

Calvin Hobbes
2019-01-18 02:29:12

Vinicius Silva
2019-01-18 02:57:43

Vinicius Silva
2019-01-18 02:58:21

Calvin Hobbes
2019-01-18 03:06:55

Vinicius Silva
2019-01-18 05:37:13

Vinicius Silva
2019-01-18 05:41:20

Calvin Hobbes
2019-01-18 06:32:37

Richard Shapiro
2019-01-19 01:32:10

Robert Silvers
2019-01-19 01:39:18

Richard Shapiro
2019-01-19 01:41:45

Martin Da Costa
2019-01-19 18:51:57

Richard Shapiro
2019-01-19 22:16:25

Vinicius Silva
2019-01-23 10:08:08

Calvin Hobbes
2019-01-23 11:32:51

Susan Sioux Mercer
2019-01-23 12:33:43

Susan Sioux Mercer
2019-01-23 12:49:28

Robert Silvers
2019-01-23 12:59:38

Martin Da Costa
2019-01-23 14:47:41

Robert Silvers
2019-01-23 14:51:18

Susan Sioux Mercer
2019-01-23 15:03:06

Kevin Reynolds
2019-01-26 08:53:49

Susan Sioux Mercer
2019-01-26 10:44:13

Martin Da Costa
2019-01-26 16:28:12

Susan Sioux Mercer
2019-01-26 16:48:04

Susan Sioux Mercer
2019-01-26 17:14:07

Martin Da Costa
2019-01-26 17:40:40

Robert Silvers
2019-01-31 11:05:39

Susan Sioux Mercer
2019-01-31 11:09:27

Martin Da Costa
2019-01-31 16:14:42

Vinicius Silva
2019-01-31 17:44:17

Robert Silvers
2019-01-31 20:17:45

Martin Da Costa
2019-01-31 21:38:41

Robert Silvers
2019-01-31 21:41:48

Martin Da Costa
2019-01-31 21:46:27

Robert Silvers
2019-01-31 21:53:21

Martin Da Costa
2019-01-31 21:54:52

Martin Da Costa
2019-02-01 22:22:08

Martin Da Costa
2019-02-01 22:23:00

Martin Da Costa
2019-02-01 22:23:09

Martin Da Costa
2019-02-01 22:23:22

Martin Da Costa
2019-02-01 22:23:35

Martin Da Costa
2019-02-01 22:23:45

Martin Da Costa
2019-02-01 22:24:05

Martin Da Costa
2019-02-01 22:24:16

Martin Da Costa
2019-02-01 22:24:24

Calvin Hobbes
2019-02-07 08:05:07

Vinicius Silva
2019-02-07 10:42:04

Ivan N. Potocnik
2019-06-05 00:39:04

Robert Silvers
2019-06-11 01:48:37

Petr Osipov
2019-11-06 22:35:22

Simon Wilson
2019-11-20 14:16:18

Harrie Kools
2020-01-30 23:16:43

Vinicius Silva
2020-01-31 00:02:30

原文網址 Michael Inwood
2018-12-31 22:14:10

Quick question, I need to get a power supply for my photon, u know its 12 volts, but can anyone tell me what amps ? Thanks

翻譯年糕

Sen Kun
2018-12-31 22:24:31

原文網址 Dana Turner
2018-12-28 00:01:25

Going down the rabbit hole of LCD flickering issues... have determined that the DRAM on my mainboard has a deformity on the VSS pin (Ground) and solder on several other pins is not as clean as it should be. Also, It appears that in newer boards, they are using a different DRAM. I really would like to get my hands on a new board... But for now, will try a hot air reflow and test voltages on the chip.

翻譯年糕

Vinicius Silva
2018-12-28 00:26:14

Frank Baeyens
2018-12-28 00:31:14

Dana Turner
2018-12-28 03:11:32

Sen Kun
2018-12-28 03:19:09

Dana Turner
2018-12-28 09:55:25

Dana Turner
2018-12-28 10:36:13

Dana Turner
2018-12-28 10:38:00

Vinicius Silva
2018-12-28 11:09:13

Dana Turner
2018-12-28 11:10:11

Dana Turner
2018-12-28 11:34:50

Dana Turner
2018-12-28 12:41:00

Dana Turner
2018-12-28 13:53:22

Dana Turner
2018-12-28 20:22:08

Dana Turner
2018-12-29 01:57:59

Sen Kun
2018-12-29 03:06:20

Dana Turner
2018-12-29 06:45:51

Dana Turner
2018-12-29 09:16:29

Dana Turner
2018-12-29 09:27:25

Dana Turner
2018-12-29 09:28:24

Dana Turner
2018-12-29 22:09:54

Dana Turner
2018-12-29 22:10:42

Vinicius Silva
2019-04-09 21:06:30

Vinicius Silva
2019-04-09 21:09:45

Dana Turner
2019-05-03 10:33:00

Vinicius Silva
2019-05-03 11:31:35

原文網址 Dave Fusinato
2018-11-06 00:40:05

So my new photon arrived yesterday. Did not even turn on. Checked the power converter output with a volt meter and saw a steady 12 volts. Very disappointed. It is being returned and another one is on the way.
I'm thinking this may be a very delicate unit that gets easily damaged during shipping.

翻譯年糕

全不選發文排行