Anycubic Photon Printer Owners 造訪社團 » 測試

Sorry not about my Photons but wow just wow!

Got my Sonic Mini! Did the rings test print. Wow! I am really impressed! Used Polyjuice water washable resin from Filaments.ca. And even at 2 sec exposure it worked great! Man that was fast. Less than 2 hours. And great detail...

抱歉不是我的光子, 但哇!

得到了我的音速迷你! 戒指測試列印了. 哇! 我真的印象深刻! 用過的多汁水可洗樹脂. Ca. 即使在2秒曝光時, 它效果很好! 男人, 那太快了. 不到2小時. "我知道, 我是一個非常棒的

· 查看原文 · 為此翻譯評分

My first FEP yay :cough: sadly after my first test prints the resin became glued to the fep. Being a noob I scrapped it off which slightly scratched the old fep. So after a few YouTube videos I replaced mine. Not sure if the tuning really matters but it drums to 303 hz.

我的第一個fep yay: 咳嗽: 可悲的是我第一次測試列印後, 樹脂被粘在fep上. 作為一個新手, 我把它刪除了, 稍微刮了舊fep. 所以在幾個youtube視訊之後, 我換了我的. 不確定調音是否真的重要, 但它鼓到303赫茲.

· 查看原文 · 為此翻譯評分

A big ‘thank you’ to this group!
I’m fairly new to 3D printing, bought my Photon S last November and I’m having fun printing 40k minis. Been learning through lots of trial and error. Went thru a 1Lt. bottle of AnyCubic Macaroon Blue ECO resin. Unfortunately, my models have all suffered from over exposure because I read some bad information regarding the ECO resin and settings. I was lead to believe that I should be using 12sec exposure times at 0.02mm layers. My mini models were losing details like crazy and I was getting frustrated because I knew it could be better.

This group is helping my understand this machine better and I greatly appreciate the collective knowledge that everyone is willing to share.

I’ve been experimenting more lately with the AmeraLabs SLA tests. I think I’m getting closer to a good balance with the details.

Number one lesson y’all taught me so far:
“The print exposure is too damn high.” Lol
So I made a meme for it lol

給這個社團的"謝謝"!
我相當新到3 d列印, 去年十一月買了我的光子s, 我很開心印刷40 k minis. 經歷了很多考驗和錯誤. 穿過1 lt. 一瓶任何cubic macaroon blue eco樹脂. 遺憾的是, 我的模特都因為我閱讀了一些關於生態樹脂和設定的壞資訊而遭受了影響. 我相信我應該在0.02 mm層使用12秒曝光時間. 我的迷你模特像瘋了一樣失去了細節, 我感到沮喪, 因為我知道它會更好.

這個小組幫助我更好地理解這台機器, 我非常感謝大家願意分享的集體知識.

最近我一直在嘗試ameralabs sla測試. 我想我越來越接近與細節的平衡.

到目前為止, 你們都教我的第一課:
"列印曝光太高了." lol
所以我為此做了一個meme lol

· 查看原文 · 為此翻譯評分

Once again failed test print, tried of cleaning this out and dumping back resin, anyone able to help me level/ calibrate, followed the instructions(I thought)

再次失敗的測試列印, 嘗試清理這個並扔回樹脂, 有人能幫助我水平/校准, 遵循指示(我想)

· 查看原文 · 為此翻譯評分

Getting ready for my first test print. I noticed that the glasses of my Photon are opaque. Is that normal? All photons out there are transparent right? Do i have to scratch the protection to make it transparent, or i can leave it like this?

準備好我的第一個測試列印. 我注意到我的光子的眼鏡是不透明的. 這正常嗎? 外面所有的光子都是透明的對吧? 我必須抓抓保護才能讓它透明, 還是這樣離開它?

· 查看原文 · 為此翻譯評分

Requesting some input!
The problem:
Anycubic Skin refuses to adhere to the buildplate.
It just gets cured to the bottom of the vat on the FEP.
Dragon Resin Grey is adhering and printing successfully without issue. Anycubic Skin will not, regardless of exposure settings.

Troubleshooting:
- FEP was replaced several prints ago - prints remained successful afterwards when printing in Grey resin.
- I have tried several different exposure settings and 2 different objects. Skin Always fails.
- I have re-leveled the build plate.
- Printed the same test objects, using my Dragon Resin (Grey), with success The Grey adheres to the print bed without issue. The Anycubic Skin does not.
-Temperature of the room is maintained using a space heater between 60-75 degrees
- Resin is stored in a comfortable indoor temperature (72 degrees)
- Resin is always shaken before pouring

Test Object:
- Test object is a flat disk-like pendant that is printed flat against the build plate. this test object has printed successfully numerous times in two other types of resin.
- I have also printed other objects with success in grey, that skin fails. I have yet to have a single successful print in Skin.
My thoughts:
> I do not think this is a leveling issue.
> My only conclusion is, do I have a bad bottle of resin?
> Anycubic Skin was purchased via Amazon
> Anycubic Skin has a lot of bubbles after shaking, but it's less viscous than Dragon Resin so it may not indicate any problem but I'll mention it anyways.
Successful Grey print settings (A little overexposed but at least it adhered)but Trying the same in Skin yielded no success.
Normal Exposure: 15sec
Offtime: 7 sec
Base Exposure: 70sec
Base Layers: 8

Failed Skin settings:
Normal Exposure: 5sec
Offtime: 2sec
Base Exposure: 50sec
Base Layers: 8sec

請求一些意見!
問題:
Anycubic面板拒絕遵守建築板.
它剛剛被治癒到fep上的增值稅底部.
龍樹脂灰色成功地堅持和列印, 沒有問題. 任何cubic面板不會, 不管曝光設定.

煩惱:
- fep在幾張列印之前被更換-之後印刷灰色樹脂時, 列印仍然很成功.
-我嘗試了幾個不同的曝光設定和2個不同的物體. 面板總是失敗.
-我重新調整了建造盤子.
-用我的龍樹脂(灰色)列印同樣的測試物件, 成功, 灰色堅持在列印床上. Anycubic面板沒有.
-房間的溫度是使用60-75度之間的空間加熱器保持.
-樹脂儲存在舒適的室內溫度(72度)
-樹脂在傾盆前總是動搖

測試物件:
-測試物件是一個平盤一樣的吊墜, 列印平板. 這個測試物件已經成功地印刷了另外兩種樹脂.
-我也印刷了其他在灰色中成功的物體, 面板失敗了. 我還沒有一個成功的面板列印.

我的想法:
>我不認為這是一個平凡的問題.
>我唯一的結論是, 我有一瓶樹脂嗎?
> anycubic面板是通過亞馬遜購買的
> anycubic面板在搖晃後有很多泡泡, 但它比龍樹脂少, 所以它可能不會顯示任何問題, 但無論如何我會提到它.

成功的灰色列印設定(有點過量, 但至少它堅持), 但在面板嘗試同樣的嘗試沒有成功.
正常曝光: 15秒
時間: 7秒
基底曝光: 70秒
底層: 8

面板設定失敗:
正常曝光: 5秒
時間: 2秒
基底曝光: 50秒
底層: 8秒

· 查看原文 · 為此翻譯評分

Hi everyone. Since a couple of weeks I´m working on a customizer tool for miniatures (similar to heroforge), but also with dragons, beast creatures, spiders and stuff like that. As a test, I shared my Owlbear for free on my profile at myminifactory: https://www.myminifactory.com/users/Rober%20Rollin My own print with a resin printer turns out pretty smooth, but it would be awesome if you could also give it a try and give me some feedback. I want to create the best possible tool for you. Regards.

大家好. 幾個星期以來, 我正在製作一個客製化工具(類似於heroforge), 但也與龍, 野獸生物, 蜘蛛等東西. 作為一個測試, 我在myminifactory的個人檔案上免費分享了我的owlbear: https://www.myminifactory.com/users/Rober%20Rollin我自己的印表機 , 結果相當順利, 但如果你也能給我一些反饋給我一些反饋. 我想為你創造最好的工具. 問候.

· 查看原文 · 為此翻譯評分

Got my Anycubic Skin and did an exposure test.
Which one do you think looks the best? O:

(This is a bunch of photos of the same single test, my phone camera isn't great so hopefully the multiple photos helps show detail.)

得到了我的anycubic面板並做了一個曝光測試.
你認為哪個看起來最好? O:

(這是同一次測試的一堆照片, 我的手機相機不是很棒, 希望多張照片能顯示細節. 年一月日

· 查看原文 · 為此翻譯評分

My FDM is driving me nuts at the moment (TMC CONNECTION ERROR) but the Photon S gave me a nice result on this miniature I’ve made to test my custom support settings.

The post process felt actually kind of as “de stressing” ...

4cm total height
Roughly 3.2 cm to the top of the head

我的fdm目前正在讓我發瘋(tmc連線錯誤), 但光子s給了我一個很好的結果, 以測試我的定制支援設定.

"如果你知道, 你會知道, 我是甚麼意思嗎...

4釐米總高度
頭頂大約3.2釐米

· 查看原文 · 為此翻譯評分

Hello everyone.I printed this powerful 775 motor and printed using PLA material.Tested with 775 motor. I hope you enjoy this video.Download link is on YT. And hope you support our channel because i really work hard and im taking nothing:/.Greetings..

大家好. 我用pla材料印刷了這輛強大的775馬達並印刷. 用775馬達測試. 我希望你喜歡這段視訊. 下載連結在yt上. 希望你支援我們的頻道, 因為我真的很努力工作, 我拿nothing:/.Greetings..

https://youtu.be/DaBQdfX5xak

· 查看原文 · 為此翻譯評分