Anycubic Photon Printer Owners 造訪社團 » 設定

Hey guys, it's me again, clueless enthusiast! So i've been wondering what's your recommended settings to print a very detailed custom head for something like, a hot toys collectible.

嘿, 朋友們, 又是我, 無知的愛好者! 所以我一直在想, 你推薦的設定是甚麼來列印一個非常詳細的定制頭, 一個熱玩具收藏.

· 查看原文 · 為此翻譯評分

Requesting some input!
The problem:
Anycubic Skin refuses to adhere to the buildplate.
It just gets cured to the bottom of the vat on the FEP.
Dragon Resin Grey is adhering and printing successfully without issue. Anycubic Skin will not, regardless of exposure settings.

Troubleshooting:
- FEP was replaced several prints ago - prints remained successful afterwards when printing in Grey resin.
- I have tried several different exposure settings and 2 different objects. Skin Always fails.
- I have re-leveled the build plate.
- Printed the same test objects, using my Dragon Resin (Grey), with success The Grey adheres to the print bed without issue. The Anycubic Skin does not.
-Temperature of the room is maintained using a space heater between 60-75 degrees
- Resin is stored in a comfortable indoor temperature (72 degrees)
- Resin is always shaken before pouring

Test Object:
- Test object is a flat disk-like pendant that is printed flat against the build plate. this test object has printed successfully numerous times in two other types of resin.
- I have also printed other objects with success in grey, that skin fails. I have yet to have a single successful print in Skin.
My thoughts:
> I do not think this is a leveling issue.
> My only conclusion is, do I have a bad bottle of resin?
> Anycubic Skin was purchased via Amazon
> Anycubic Skin has a lot of bubbles after shaking, but it's less viscous than Dragon Resin so it may not indicate any problem but I'll mention it anyways.
Successful Grey print settings (A little overexposed but at least it adhered)but Trying the same in Skin yielded no success.
Normal Exposure: 15sec
Offtime: 7 sec
Base Exposure: 70sec
Base Layers: 8

Failed Skin settings:
Normal Exposure: 5sec
Offtime: 2sec
Base Exposure: 50sec
Base Layers: 8sec

請求一些意見!
問題:
Anycubic面板拒絕遵守建築板.
它剛剛被治癒到fep上的增值稅底部.
龍樹脂灰色成功地堅持和列印, 沒有問題. 任何cubic面板不會, 不管曝光設定.

煩惱:
- fep在幾張列印之前被更換-之後印刷灰色樹脂時, 列印仍然很成功.
-我嘗試了幾個不同的曝光設定和2個不同的物體. 面板總是失敗.
-我重新調整了建造盤子.
-用我的龍樹脂(灰色)列印同樣的測試物件, 成功, 灰色堅持在列印床上. Anycubic面板沒有.
-房間的溫度是使用60-75度之間的空間加熱器保持.
-樹脂儲存在舒適的室內溫度(72度)
-樹脂在傾盆前總是動搖

測試物件:
-測試物件是一個平盤一樣的吊墜, 列印平板. 這個測試物件已經成功地印刷了另外兩種樹脂.
-我也印刷了其他在灰色中成功的物體, 面板失敗了. 我還沒有一個成功的面板列印.

我的想法:
>我不認為這是一個平凡的問題.
>我唯一的結論是, 我有一瓶樹脂嗎?
> anycubic面板是通過亞馬遜購買的
> anycubic面板在搖晃後有很多泡泡, 但它比龍樹脂少, 所以它可能不會顯示任何問題, 但無論如何我會提到它.

成功的灰色列印設定(有點過量, 但至少它堅持), 但在面板嘗試同樣的嘗試沒有成功.
正常曝光: 15秒
時間: 7秒
基底曝光: 70秒
底層: 8

面板設定失敗:
正常曝光: 5秒
時間: 2秒
基底曝光: 50秒
底層: 8秒

· 查看原文 · 為此翻譯評分

Anyone used anycubic white at 0.02? If so what setting you using, just after an idea, yes I've seen the spreadsheet. Anyone used anycubic white at 0.02? If so what setting you using, just after an idea, yes I've seen the spreadsheet.

有人在0.02點使用任何人白色嗎? 如果如此, 你使用甚麼設定, 只是在一個想法之後, 是的, 我已經看到了試算表.

· 為此翻譯評分

My FDM is driving me nuts at the moment (TMC CONNECTION ERROR) but the Photon S gave me a nice result on this miniature I’ve made to test my custom support settings.

The post process felt actually kind of as “de stressing” ...

4cm total height
Roughly 3.2 cm to the top of the head

我的fdm目前正在讓我發瘋(tmc連線錯誤), 但光子s給了我一個很好的結果, 以測試我的定制支援設定.

"如果你知道, 你會知道, 我是甚麼意思嗎...

4釐米總高度
頭頂大約3.2釐米

· 查看原文 · 為此翻譯評分

I am slicing in Chitu box , using the hollow function.

Have a Photon S

So when I open in Photon Workshop - Sliced view it does not show any of the Z lift distance etc , they are all set to 0

Will that work , cannot find a way to edit that ?

Its a 9 hour print , would prefer to get this right .

Also , if I then save the PWS from sliced view , and try to open in Photon Workshop it just crashes.

File is 345 mb , largest one i have seen , not sure if that is a problem?

Aaand it shows a blank preview on the printer., failed to open file.

EDIT: Is there a way to save from Chitubox or Photon validator something I can use directly for the printer rather then having to always use the Photon workshop ?

It seems I have to use that to make the PWS format , but that is where everything gets messed up .

我在chitu box切片, 使用空洞功能.

有一個photon s

所以當我在光子工作室開啟時-切片的視野沒有顯示任何z電梯距離等, 它們都設定為0

這有用嗎, 找不到編輯的方法?

這是一個9小時的列印, 更願意把它弄清楚.

另外, 如果我把pws從切片視野中拯救出來, 並試圖在光子工作坊開啟, 它就崩潰了.

檔案是345 mb, 我看到的最大的, 不確定這是問題嗎?

它顯示印表機上的空白預覽., 無法開啟檔案.

編輯: 是否有辦法從chitubox或光子驗證器中拯救一些東西, 我可以直接用於印表機, 而不用總是使用光子工作坊?

看來我必須用它來製作pws格式, 但這就是一切都搞砸的地方.

· 查看原文 · 為此翻譯評分

Hi! I'm looking for more suggestions on resins to print a Ball Jointed Doll with! It needs to be sturdy enough to withstand tension when strung together with elastic.

[NOTE: I plan on making a mold, but a client wants one that's 3D printed , rather than waiting for me to make a finalized one via silicone molds & casting resin]

These are the types I've used:
- Anycubic Green printed in wonderfully crisp detail, but it's very brittle and probably wont withstand being held by elastic for very long.
- Dragon Resin (White) I'm really liking since it's flexible!
- Dragon Resin (Grey) Its also flexible but my prints aren't coming out as nicely, which could be my own issues with temperature and exposure settings
- I'm thinking of buying Dragon Resin (Flesh tone) but also want to try other brands too!

But I'm looking for some more recommendations for relatively sturdy, but more flexible resin (not brittle like Anycubic) Ideally in Skin-tone/Flesh color!

Thanks for looking! <:

嗨! 我正在尋找更多關於樹脂的建議, 以印出一個球關節娃娃! 當與彈性纏住時, 它需要足夠堅固地承受緊張.

[注: 我計劃製作一個模具, 但客戶想要一個3 d列印的, 而不是等我通過矽膠和鑄造樹脂]

這些是我使用的類型:
- anycubic green列印的細節非常簡潔, 但它非常微小, 可能無法忍受被彈性控制很久.
-龍樹脂(白)我真的很喜歡, 因為它很靈活!
-龍樹脂(灰色)也很靈活, 但我的列印沒有那麼好, 這可能是我自己的溫度和曝光設定的問題
-我想買龍樹脂(肉色調), 但也想嘗試其他品牌!

但我正在尋找一些更多的建議, 以比較堅固的樹脂(不像anycubic)最好是面板色調/肉體顏色!

謝謝你的尋找! <:

· 查看原文 · 為此翻譯評分

Sorry... another newbie question.
I’ve sliced my print use Chitubox and set Z-height to 32mm

So I’ve expected a print of 3.2cm height ... but in fact it is about 2.5cm. Is there some factor that I need to keep in mind to get the expected dimensions?

對不起... 又一個新人問題.
我已經切開了我的列印使用chitubox, 並將z-高度設定為32 mm

所以我預期列印3.2釐米高度... 但事實上它大約是2.5釐米. 有甚麼因素, 我需要記住才能獲得預期的尺寸?

· 查看原文 · 為此翻譯評分

Hi ,i need some help ,how to setting for Gray Resin with Anycubic Photon S , right now im using my setting but support is so strong and hard to cut support out from the parts, Thank.

嗨, 我需要一些幫助, 如何用任何立方光子s來設定灰色樹脂, 現在我現在使用我的設定, 但支援是如此強大, 很難從零件中切斷支援, 謝謝.

· 查看原文 · 為此翻譯評分

Hello champions of The fellowship of the Photon,

I have had to put my head on something for the weekend and this came out:
It's an upgrade to the draining bracket that you don't have to set up after each print. It just sits there, attached to the build plate so that you just have to
- release the build plate from the Z carriage,
- fix it in draining position.

Anycubic Photon draining bracket found on # Thingiverse https://www.thingiverse.com/thing:4130991

Hope some of you will find it useful ❤️

你好光子聯誼會冠軍,

週末我不得不把我的頭放在某事上, 結果出來了:
這是一個升級到排水括號, 你不必在每次列印後設定. 它只是坐在那裡, 附在構建板上, 所以你只需要
-釋放z車廂的構造板,
-把它放在排水位置.

在#thingiverse上發現任何立方體光子排水括號https://www.thingiverse.com/thing:4130991

希望你們有些人會覺得有用 ❤️

· 查看原文 · 為此翻譯評分

Ok good news. With the tips you guys have given me, thanks Joe for the settings, I have my first successful prints that are not the test print.

I might have gone over board on the supports but at least I'm starting to dial it in :)

好的好訊息. 有了你們給我的提示, 感謝的設定, 我有第一個成功的指紋不是測試列印.

我可能已經在支援上過頭, 但至少我開始撥號了 :)

· 查看原文 · 為此翻譯評分