Anycubic Photon Printer Owners 造訪社團 » 設定

Hi there, i just did the "photon s resin exposure finder" with anycubic black, what do you think is the best? In my opinion they all look shity :(

What for settings domyou recommend for anycubic black? I took the settings from the google list for photon s, but iam not sure if i should try 7 seconds normal exposure time.

嗨, 我剛用任何立方體黑色做了"光子 s 樹脂 曝光 探測器", 你覺得最棒? 在我看來, 他們看起來都很害羞 :(

Domyou推薦任何立方體黑色的設定是甚麼? 我從谷歌列表中獲取了光子s的設定, 但我不確定是否應該嘗試正常曝光時間.

· 查看原文 · 為此翻譯評分

HELP!!! my first prints don't attach on Z-plate. First try (with manual instruction): set Z-axis moving the plate until paper sheet moves not freely. fix the plate with wrench set Z-height as 0 (Tools -> Z=0) PRINT
Second try (following this video https://www.youtube.com/watch?v=j6XHlSyj2ZU ) set Z-axis moving the plate until paper sheet moves not freely. fix the plate with wrench move up the plate and put the vat in its slot move the plate down until the vat moves not freely. set Z-height as 0 (Tools -> Z=0) PRINT
Both prints was paused (3-5%) in order to check if it was attached to the plate, but it was on the bottom of vat. What i'm doing wrong?? ?

救命!!! 我的第一個指紋不附在z板上.
第一次嘗試(手動指示):
設定z軸移動盤子直到紙張不自由移動.
用扳手修理盤子
將z高度設定為0 (工具-> z =0)
印刷

第二次嘗試(關注這個視訊https://www.youtube.com/watch?v=j6XHlSyj2ZU)
設定z軸移動盤子直到紙張不自由移動.
用扳手修理盤子
抬起盤子, 把增值稅放進它的位置
把盤子向下移動, 直到增值稅不自由移動.
將z高度設定為0 (工具-> z =0)
印刷

兩張列印都暫停(3-5 %), 以檢查是否附在盤子上, 但它在增值稅底部.
我做錯了甚麼?? ?

· 查看原文 · 為此翻譯評分

Ok. I printed this building, and the front side failed to stick to the plate. So I rotated it 180° and tried again. The portion that failed before worked, but then the opposite side failed. Her are my supports and settings.

Is it a leveling issue, is the fep too loose/tight. Elegoo grey.

好吧. 我列印了這棟建築, 而前方沒能堅持到盤子上. 所以我旋轉了180°並再試一次. 之前失敗了, 但後來對方失敗了. 她是我的支援和設定.

這是一個平穩的問題, fep太鬆松/緊了. Elegoo grey.

· 查看原文 · 為此翻譯評分

Hello all! I just got my Anycubic Photon printer last night. I'm 100% new to 3D printing (I'm primarily an artist that creates 3d models and illustration but I've always wanted to have my models printed physically.) I have TWO Questions, with images provided.

Firstly, I printed a tiny benchy as a test of the Printer.
The print went well for most of the model but towards the end, Benchy fell off the print bed for some reason. I found it floating in the resin vat.
Could this be due to a leveling issue, or perhaps an exposure duration issue? Or a mix of both? Any advice in identifying the issues when it comes to learning the mysterious process of printing as a newbie to all this?
I believe the settings in the file were as follows

Layer Thickness: 0.05
Exposure time: 10.5
Off Time: 1
Bottom Exposure Time: 80
Bottom Layers: 8

- - - -

Secondly,
I want to print the model I made of one of my characters. He's definitely more complex than a basic Benchy Boat, and I used the provided Slicer software to auto-generate supports. My question for this model would be:
1. Does it need supports added at the tip of the braid and sidebangs? Or will those (ideally) cure to the printer bed and form as it rises?
2. Would the settings shown in the image be adequate exposure and layer thickness time for this type of a model?

Sorry for all the noob questions. But I appreciate any input, as well as any helpful links and resources so I can do some reading on my own as well.
Thank you! :)

大家好! 我昨晚剛拿到了我的任何立方體光子印表機. 我對3 d列印是100 %的新手(我主要是一個製作3 d模型和插圖的藝術家, 但我一直想要把我的模特列印出來.)我有兩個問題, 提供了影象 "我想讓我們知道,

首先, 我列印了一個小小的基準作為印表機的測試.
大多數模型的印刷品都很好, 但最終, 基準因某種原因從印刷床上掉下來. 我發現它漂浮在樹脂增值稅.
這可能是因為一個平穩的問題, 還是曝光時間問題? 還是兩者混合? 當學習作為新手印刷的神秘過程時, 有甚麼建議來識別問題嗎?
我相信檔案中的設定如下

層厚度: 0.05
曝光時間: 10.5
休息時間: 1
底部曝光時間: 80
底層: 8

- - - -

第二,
我想列印我用我的一個角色製作的模型. 他絕對比基本的基準船複雜, 我使用了提供的切片軟體自動生成支援. 我對這個模型的問題是:
1., 它是否需要在braid and sidebang頂端新增支援嗎? 或者那些(理想)會治癒印表機床, 隨著印表機上升時形成?
2. 影象中顯示的設定對於這類模型來說是否足夠曝光和層厚度時間?

抱歉所有的新手問題. 但我感謝任何投入, 以及任何有用的連結和資源, 這樣我也可以自己閱讀.
謝謝! 你知道嗎?

· 查看原文 · 為此翻譯評分

Hey Guys, so... i have a few questions i would like for the community to help me with. Sorry it will be a bit of a long post xD.

I got my Photon this week. Here's what i did (questions come after :p ).

- Checked everything was working properly working, turned on the printer, checked if the Z-Axis was moving, if the screen was ok, etc.

- Ditched the stock PSU and USB drive (tested the PSU and its outputing the correct voltage but i ditched it anyway), im using another one i had here with the exact same specs, USB drive im now using a Kingston one.

- Disconnected the "smelling" fan from the main board to avoid the fumes from getting out and stinking up the place. (Planing to upgrade the stock led cooling fan, suggestions???)

- Checked every screw to see if everything was properly tightened (the buildplate wasnt, it would move even after tightening the grub screw).

- Checked the FEP tension with a sound analyzer, it was below 300hz... tuned it to 345-355hz.

- Applied Kapton tape to the borders of the screen (to avoid a spill going into the machine in case that happens).

- Adjusted the buildplate to be completely flat against the screen, made sure that the plate was making even pressure on the paper on all sides (front, back, left and right). After that i leveled the printer and set the new Z=0 (didnt forget to hit Home first :p ).

- Finally i heated up the resin (room temp was 19C) and started the default print file that came with the printer (photos attached).

So, now some questions.

1 - The new yellow windows, how good are they at blocking UV? The printer is not on a direct sunlight enviroment, not even daylight for that matter, but the room does have okayish lighting (there is no light directly above the printer), i am safe to assume resin wont cure while inside? I know i can cover up the printer but im trying to understand if its really necessary.

2 - Do you guys filter the resin and clean the vat after every print? I saw some people mentioning it... but to be completely honest i've never done that with my other printer, well... my other printer doesnt have the leaking risk this one has... So... what do you guys do?

3 - Firmware... my printer came with version 4.2.3... I dont see that in Anycubic site, anyone has the changelog for this fw? Just curious.

4 - Recommendations for resin, im looking for high detail. Impact resistance is not really important right now (Anycubic resins, how do they stack up against the competition?)

5 - Which one is better for the screen to last more? Slow or fast resins?

And for now thats it! Thanks guys...one of the reasons i got the Photon was for this awesome community =)

嘿, 夥計們, 所以... 我有幾個問題想讓社羣幫我解決. 抱歉, 這將是一個漫長的帖子xd.

我這周得到了我的光子. 這就是我所做的(問題之後: p).

-檢查一切正常運作, 開啟印表機, 檢查z軸是否移動, 螢幕是否正常等等.

-丟棄了存貨psu和usb驅動器(測試psu及其輸出正確的電壓, 但我還是拋棄了它), 我在這裡使用了另一個, usb驅動器, usb驅動器現在使用金斯敦.

-從主板上斷開"聞"風扇, 以避免煙霧出來, 讓地方臭. (計劃升級庫存led冷卻風扇, 建議???)

-檢查了每個螺絲, 看一切是否都收緊了(建築板沒有, 甚至在收緊後也會移動).

-用音效分析儀檢查了fep緊張, 低於300 hz... 調到345-355 hz.

-將kapton磁帶應用到螢幕的邊界(以防發生洩漏到機器).

-調整構建板完全平坦, 以確保板塊對紙板對紙面(前, 背面, 左和右)施加壓力. 之後, 我平平了印表機, 設定了新的z =0 (沒有忘記先打家: p).

-最後我加熱樹脂(房間溫度為19 c), 並啓動了印表機的預設列印檔案(照片附後).

所以, 現在有一些問題.

1-新的黃色窗戶, 阻擋紫外線有多好? 印表機不在直接陽光環境上, 連白天也沒有, 但房間確實有okayish照明(印表機上方沒有光), 我可以安全地假設樹脂治癒嗎? 我知道我可以掩飾印表機, 但我試著理解是否真的有必要.

2-你們在每次列印後過濾樹脂並清理增值稅嗎? 我看到有些人提到它... 但老實說, 我從來沒有和我的另一個印表機做過, 好吧... 我的另一個印表機沒有洩漏風險... 那麼... 你們這些傢伙是甚麼? 做甚麼?

3-固件... 我的印表機有4.2.3. 版.. 我沒看到在任何立方體網站, 有人有這個fw的改裝? 只是好奇.

4-樹脂推薦, 我正在尋找詳細的細節. 現在抵御衝擊並不重要(任何立方體樹脂, 他們是如何堆積起來對抗競爭的?) 你知道嗎?

5-哪一個更好讓螢幕持續更多? 慢或快速樹脂?

現在就這樣! 謝謝大家... 我得到光子的原因之一是這個很棒的社羣=)

· 查看原文 · 為此翻譯評分

Hi Guys,

Have people knows how to change the speed of the Z-axis as it move up and down setting ?

Due to we want to print the sample object model , have many area can not print finish.

My personal feeling is that the current Z-axis as it move up and down speed is too fast.

Can help me to clearly my question ?

Many Thanks.

===========================================
Update : 20180922

我終於看懂
https://raw.githubusercontent.com/…/resin-…/print-mode.gcode

這裡面的設定資訊.

1.
控制首層的抬升距離 使用 M8070 S3
控制首層的抬升速度 使用 M8015 T2

2.
控制剝離抬升的距離 使用 M8070 Z6
控制剝離的抬升速 使用 M8016 T3

Philippe Maegerman

These lines are for the speed T1 is slower, T2 faster, T3, T4 etc ...
then you save and you print this file, it will update the firmware

;(Peel and lift speeds)
;M8015 T2
; Initial peel speed slow move
;
;M8016 T3
; Build plate raise and lower speeds between layers

Vinicius Silva

Many thanks for provide help for me guys.

翻譯年糕

Anyone got the settings for wanhao resin?

誰有wanhao樹脂的設定嗎?

· 查看原文 · 為此翻譯評分