Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Ксения Ксения
2019-01-14 05:00:56

Success finally :) )) still figuring out how to properly work with supports, but super happy! Do any of you sand your models? And how do you repair them if small piece broke off? Is it possible to use the resin to glue?

翻譯年糕

Ian Adams
2019-01-14 05:09:17

Nick Williams
2019-01-14 05:09:22

Nick Williams
2019-01-14 05:09:32

Ксения Ксения
2019-01-14 06:13:33

Nick Williams
2019-01-14 06:16:17

Ксения Ксения
2019-01-14 06:17:24

Nick Williams
2019-01-14 06:18:05

Ксения Ксения
2019-01-14 06:18:37

Lia Vignando
2019-01-14 08:02:33

Nick Williams
2019-01-14 08:04:55

David McGyver
2019-01-14 09:38:03

Julien Fournier
2019-01-14 09:43:03

Richard Shapiro
2019-01-14 11:29:03

Ксения Ксения
2019-01-14 22:32:08

Ксения Ксения
2019-01-14 22:32:40

Ксения Ксения
2019-01-14 22:33:24

Richard Shapiro
2019-01-14 22:46:10

原文網址 Ксения Ксения
2019-01-10 22:34:44

Hi. Had anyone used this FEP? Is it good?

翻譯年糕

原文網址 Ксения Ксения
2019-01-09 13:17:09

Yay! Finally got something to stick AND print kind of right after a few failed attempts, but there is some delamination between layers. Any thoughts on why this may be happening? I am using # harzlabs cherry red and the settings are as shown on the screenshot. I have re-leveled the printer and changed / tightened the FEP. Thank you for any advice!

翻譯年糕

John Boyington
2019-01-09 13:27:20

Ксения Ксения
2019-01-09 13:30:24

John Boyington
2019-01-09 13:41:36

Ксения Ксения
2019-01-09 13:51:11

Konstantin Churkin
2019-01-09 19:47:04

Alexander Yurasov
2019-01-09 20:03:50

Ксения Ксения
2019-01-09 22:26:06

Alexander Yurasov
2019-01-09 22:36:30

Ксения Ксения
2019-01-10 09:54:24

Alexander Yurasov
2019-01-10 11:43:37

Alexander Yurasov
2019-01-10 11:44:59

Ксения Ксения
2019-01-10 11:46:03

Alexander Yurasov
2019-01-10 11:47:54

Ксения Ксения
2019-01-10 13:36:33

原文網址 Ксения Ксения
2019-01-02 12:21:10

Hello. I have been trying to print the passive filter box and the print failed in two different ways. The first section (on the right) came out just fine, the second one (on the left, same settings) stuck to the bottom of the vat and is distorted. The one in the middle is with adjusted exposure, but also stuck to the film and is similarly shaped, with distorted corners. What can be the cause of this? I am using harzlabs cherry model resin, which is very cool looking! Sorry if this is a basic question, but I would appreciate any clues to what might be going wrong.

翻譯年糕

James Scott Foley
2019-01-03 07:14:34

Ксения Ксения
2019-01-03 08:41:36

原文網址 Ксения Ксения
2018-09-11 07:55:40

Hi. I just got my Photon last week and was wondering what is a good paint to use on the prints. Would a regular acrylic paint work? I am trying to find something low-odor.

翻譯年糕

Dylan Kirby
2018-09-11 07:59:36