Anycubic Photon Printer Owners 造訪社團 » 用戶發文

原文網址 Dustin Skye
2019-02-09 08:14:33

Edit: Solved. The "easy leveler" I installed in place of the ball joint didn't allow enough downward reach and the arm on the Z stage was hitting the back edge of the vat. Put the ball joint back on and back to printing. Thanks to everyone that offered advice.

Hey everyone, I've got a problem that's stumping me. I've leveled my bed but when I go to print the build plate is crashing into the FEP in my vat. I've done a dry print with paper in place of the vat and don't get crashing. I'm also having all of my prints stick to the FEP, I'm guessing as a result of the build plate not being the correct distance from the FEP. I've measure the paper I'm using to level and it's .105mm whereas my FEP measures .128 mm. Is that difference enough to cause the crashing and prints sticking to the FEP? There is a .023 mm thickness difference between the paper and FEP, should I get my level with the paper and then raise the build plate .02mm before setting zero?

翻譯年糕

Richard Shapiro
2019-02-09 09:20:21

Dustin Skye
2019-02-09 09:21:02

Richard Shapiro
2019-02-09 09:21:38

Richard Shapiro
2019-02-09 09:21:52

Dustin Skye
2019-02-09 09:22:25

Richard Shapiro
2019-02-09 09:23:43

Dustin Skye
2019-02-09 09:25:41

Richard Shapiro
2019-02-09 09:29:31

Dustin Skye
2019-02-09 10:03:12

Richard Shapiro
2019-02-09 10:05:27

Dustin Skye
2019-02-09 10:10:29

Jannick Langfahl
2019-02-09 10:15:28

Dustin Skye
2019-02-09 10:48:14

Per Bekker-Madsen
2019-02-09 19:12:48

Richard Shapiro
2019-02-09 22:25:58

Dustin Skye
2019-02-09 22:28:35

原文網址 Dustin Skye
2019-02-08 07:56:20

I've designed a heater mount inspired by Robert Silvers' similar heater mount. My version screws into the spot where the factory build chamber fan goes, so the fan has to be removed. I used scissors to cut halfway through the carbonized foam so that the heater wires could pass through and the foam could semi seal the electronics from the build chamber. I had to bend the tabs where the power wires for the heater jut out to get it to fit. During the install I found that routing the power wires between the wall of the build chamber and the heater mount was a real pain in the butt so I altered the design by cutting a slot for the wires to pass through to make that easy. It's version 2 in the Thingiverse page. https://www.thingiverse.com/thing:3412210

I'm hoping to get the wiring finished up tonight so I can try out the Siraya Blu I bought.

翻譯年糕

Martin Da Costa
2019-02-09 05:23:37

Dustin Skye
2019-02-09 22:08:40

Martin Da Costa
2019-02-10 16:05:55

Casey Shiray
2019-02-11 06:14:18

Dustin Skye
2019-02-11 06:18:38

Casey Shiray
2019-02-11 06:23:53

Dustin Skye
2019-02-11 06:37:11

原文網址 Dustin Skye
2019-02-07 04:19:49

Hey everyone. I've got my Photon partially taken apart to install a heater to print Siraya Blu resin. While apart I noticed that the Z rail is tilted forward relative to the LCD screen. I assume I'm going to need to fix that if I want dimensionally accurate prints? Thanks for any input.

翻譯年糕